ELEC ENG 3110 Electric Power Systems

SpringBoot+Vue+MySQL 高校学科竞赛平台 完整可运行版(源码+文档) 本项目基于SpringBoot+Vue+MySQL构建高校学科竞赛管理平台,覆盖学生、教师、领队教师、管理员四大角色,实现竞赛发布、报名、刷题、评分、公示等全流程闭环管理。系统架构清晰,技术主流,配套完整源码、数据库脚本、万字论文、开题报告、答辩PPT及部署文档,支持一键运行,适用于毕业设计、课程设计及院系二次开发,真正实现“开箱即用”。 阅读详情

ELEC ENG 3110 Electric Power Systems

ELEC ENG 7074 Power Systems PG

(Semester 2, 2024)

Assignment 1:

Power System Frequency Control

(Due 23:00 Fri. 20September 2024 myUni Submission)

Investigation of power system frequency control using simplified models.

The objective of this assignment is to investigate some aspects of power system frequency con- trol using simplified models. The investigation is intended to provide conceptual insights only. The models are not necessarily optimized to yield the best frequency control performance. The Mathworks Simulink program, which is a companion of Matlab, will be employed to build and simulate dynamic models of the systems. Thus, the assignment will also provide an opportunity for you to become familiar with a very widely used tool for simulating dynamic systems.

The deliverable outcome is to be an engineering technical report that clearly and concisely de- tails the conduct and findings of your investigation and clear and pointed discussion of the tech- nical and engineering significance of your findings. The report  should address each of the matters and questions listed in the scope of work in Section 3. Credit will be given for innova- tive studies and analysis that either reveal other aspects of system performance or which im- prove the performance of the system.

It is recommended that you follow the guidelines for writing technical engineering reports pro- duced by The Institute of Engineering Technology and which are available at the following web-site: https://www.theiet.org/media/5182/technical-report-writing.pdf

With reference to the above guidelines your report is expected to convey information to other engineers about key aspects of the performance of the system and it is intended for selective reading. The latter point means that you should organize your report into numbered sections with informative headings.

It is strongly recommend that you approach this assignment in the same way as you would as a professional engineer conducting the project for an employer or client.

Introductory analysis is presented in Section 1 to assist in the systematic formulation of the fre- quency control model.

1      Introductory Analysis

The objective is to explore the performance of the system frequency control system as the mix of generation sources is varied. We are interested in assessing performance for different propor- tions of synchronous and asynchronous generation and how the performance of the overall fre- quency control system performs as different proportions of generation capacity are equipped with primary frequency control. The overall structure of the system model is shown in Figure 1. In this model the equivalent generator model represents the effective inertial response of the system taking into consideration that a proportion of the generation is asynchronous. A propor- tion of both the synchronous and asynchronous generation sources are not equipped with fre- quency controls and therefore do not contribute to the control of system frequency. A proportion of synchronous sources are equipped with governors which control the speed of their generators and a proportion of asynchronous sources are also equipped with frequency controllers that are used to regulate their power output so as to control system frequency.

Figure 1: Simplified model of system frequency control containing synchronous and

asynchronous sources. (Note that blocks with no input signal represent a fixed or constant

input to the model with the value shown in the block.)

1.1         Per-unit scaling and specification of generation capacities

We will use the total online generation capacity (Sb  in MW) as the base value of power. Thus, a power system load, Pl , of 0.8 per-unit means that the system is consuming 80% of the rated on-line generation capacity. (Note: We will see below that it is not necessary to specify the ac- tual value of Sb ).

To facilitate this exploration the total online generation capacity is divided into a number of components.

Sb  =  Ssb + Sab                                                                                (1)

where Ssb  and Sab  are respectively the online synchronous and online non-synchronous (or asynchronous) generation capacity.

Ssb  =  αsbSb  and Sab   =  ( 1 – αsb )Sb                                                         (2)

where αsb  is the specified proportion of the total online generation capacity which is synchro- nous.

The online synchronous generation capacity is then partitioned into the following components:

Ssb  =  Sspb + Ssub  where                                                     (3)

Sspb  =  αspbSsb  =  αspb αsbSb  and Ssub   =  ( 1 – αspb )Ssb  =  ( 1 – αspb )αsbSb               (4)

are respectively the proportion of online synchronous generation capacity with primary govern- ing control and the balance of online synchronous generation capacity is ungoverned.

The online asynchronous generation capacity is similarly partitioned into a fraction with prima- ry governing control, Sapb, and the balance of asynchronous generation which is ungoverned, Saub , where:

Sab  =  Sapb + Saub  and                                                           (5)

Sapb  =  αapbSab  =  αapb ( 1 – αsb )Sb  

Saub  =  ( 1 – αapb )Sab  =  ( 1 – αapb )( 1 – αsb )Sb                   (6)

Thus, to define the online capacities of the different types of generation represented in our mod- el the parameters αsb , αspb  and αapb  must be specified.

For example, if αsb   =  0.8  then 80% of all online generation capacity is synchronous and the balance 1 – αsb  =  0.2  (i.e. 20%) is asynchronous. If αspb   =  0.4  then 40% of the online syn- chronous generation capacity is under primary frequency control and the balance of such gen- eration   (i.e.   60%)   is   not   under   frequency   control.   In   this   example   it   means   that αsb × αspb  =  0.8 × 0.4  =  0.32  or just 32% of all online capacity is under primary frequency control.

1.2         Specification of the initial generation output

In this model we specify the initial power output from each of the generation sources. On the basis of this specification the initial system load is determined, on the assumption that the sys- tem is lossless.

The initial power output from the online synchronous generation with primary speed control is specified as a fraction βsp  of the specified online capacity Sspb  of this type of generation. The initial power output is expressed in per-unit of Sb . 

The initial output from the other types of generation are similarly specified as follows:

Pmsu0    =  βsu ( 1 – αspb )αsb

Pmap0    =  βap αapb ( 1 – αsb )         pu on Sb .

Pmau0    =  βau ( 1 – αapb )( 1 – αsb )

The initial power output from the synchronous generation sources is:

P      = P       + P

ms0                 msp0             msu0

and the initial power output from the asynchronous generation sources is:

P       = P       + P

ma0                 map0             mau0

and finally, the initial output from all generation sources is,

P     = P     + P      .                                                        (11)

Thus, to define the initial steady-state operating point of the system it is necessary to specify

βsp, βsu, βap  and βau .

It is important to distinguish between online capacity of the various generation categories and the actual (initial) power output from each of these generation categories. Thus, if, for example,

βsp  =  0.5  then it means that initially the power output of the online synchronous generation capacity  that  is  under primary  frequency  control  is  50%.  If,  furthermore,  αb   =  0.8   and αspb  =  0.4 it follows that the initial power output from all online synchronous generation ca- pacity that is under primary frequency control is:

Pmsp0    =  βsp ( αspb αb )  =  0.5 × (0.8 × 0.4)  =  0.16  pu of Sb .

1.3         Equivalent generator rotor dynamics

The transfer-function block diagram of the equivalent generator of the system is shown in Fig- ure 2.

Figure 2: Equivalent generator rotor dynamics for system

load / frequency analysis.

1.3.1       Specification of the inertia constant

The inertia constant of online synchronous generation limits the rate of change of frequency. In the model we specify the inertia constant, Hs, in per-unit of the on-line synchronous generation capacity. Typically, Hs   =  3.5 pu on Ssb .

For use in the model this inertia constant must be converted to per-unit on Sb . Thus,

1.3.2       Frequency dependent load

The system load is linearly dependent on the system-frequency perturbation as follows

Pl (f) =  (Pl0 + ΔPl0)( 1 + DΔf)                                      (13)

where f  =  ( 1 + Δf) pu is the system frequency in per-unit of the system nominal synchronous frequency, f0  =  50 Hz, Δf  is the per-unit perturbation of the system frequency and Pl0    is the initial steady-state value of the load. Note that under initial steady-state conditions the system is operating at synchronous frequency, i.e. Δf0  =  0 pu. Pl0  is the initial steady-state load on the system assuming that the system is initially operating at 50 Hz; and ΔPl0  is the applied change in system load at the nominal system frequency of 50 Hz

1.3.3       Composite rotor equation of motion for the analysis of system-frequency controls The acceleration equation of the system is, as detailed in the lectures,

  = Pm – Pl  in pu of Sb                                                               (14)

where Pm  and Pl  are respectively the generation and load, Δf  is the per-unit system-frequency perturbation and H is as defined in (12). The block diagram of this equation, including the fre- quency dependence of the load, is shown in Figure 2.

电路板功能测试系统-FCT for PCBA 电路板功能测试系统用于电路板组件(PCBA)的功能测试(FCT),满足自动化大批量生产的要求。  ● 用户根据自己需要定义测试步骤,灵活方便  ● 适合工业自动化大批量生产应用  ● 系统测试精度高,稳定可靠   一、电路板功能测试系统概述 电路板测试过程通常由多个步骤组成,每单个步骤中需要对多个物理量(电压、电流、电阻、频率、波形等)进行测试。在每个步骤测试时 阅读详情

相关推荐

9 海康视觉平台VisionMaster 上手系列:典型案例之螺丝机案例

海康视觉平台VisionMaster 上手系列:典型案例之螺丝机案例 快速入门 工业机器视觉 机器视觉

HuangGong2022的博客 7182

ELEC ENG 3110 Electric Power Systems ELEC ENG 7074 Power Systems PG Semester 2 2024 1Matlab

3110SystemsELEC ENG7074PowerSystemsPG(Semester2,2024)Assignment1:Poweranemployerorclient.SbPlSb).SbSsbSab(1)whereSsbandSabSsbαsbSbandSab= ( 1 –αsbSb(2)where αsbSsbSspb。

biliminy的博客 1953

SAP PO开发-端到端配置

1.登录PO系统,选择system landscape,将外围系统的系统信息(Software Component以下简称SC)注册到PO系统中。2.点击products注册外围系统信息。3.选择New 新建 按钮:创建一个新的系统和版本。4.输入产品名称、供应商、版本号等信息。然后点击:Next。5.设置instance 名称,然后点击Next。6.最后设置软件组件的名称,然后点击Finish。

P9QCer的博客 1583

InnoDB 内存结构总览:Change Buffer、AHI 与 Log Buffer

本文系统梳理InnoDB内存结构中的ChangeBuffer、Adaptive Hash Index(AHI)与LogBuffer。ChangeBuffer缓存二级索引页不在内存时的变更,减少随机IO,仅在页加载时合并;聚簇索引修改立即执行,因数据本身不可延后。AHI基于高频等值查询自动构建哈希索引,加速定位,仅支持等值操作。LogBuffer为redo log内存缓冲,配合磁盘日志实现崩溃恢复。三者均服务于性能优化,其中ChangeBuffer与AHI共享BufferPool空间,而LogBuffer独立

bksczm的博客 307

Research Proposal:自动驾驶 行人运动预测

Research Proposal about Pedestrian/Cyclist Motion Prediction for Self-Driving Vehicles   If I can be provided with the opportunity to conduct PhD research in pedestrian/cyclist motion prediction for...

Poetry Wanderer的博客 3088

服务器安全配置:二、本地安全策略设置

密码最长使⽤期限”设置为“90天”;“⽤可以还原的加密来存储密码”设置为“禁⽤”“复位账户锁定计数器”设置为15分钟,贴图这里是我自己设置的时间,15分钟也够用,具体看自己需要。”网络访问: 不允许 SAM 帐户和共享的匿名枚举“设置为“已启用””网络访问: 限制对命名管道和共享的匿名访问“设置为“已启用””网络访问: 不允许匿名枚举 SAM 帐户“设置为“已启用”“关机: 允许系统在未登录的情况下关闭”设置为“已禁用”(1)交互式登录:不显示最后的⽤户名”设置为“已启⽤”

weixin_48825672的博客 3137

第三篇 第 6 课

前置:第三篇第 1 课(stdx 引入),第二篇第 1 课(std.regex)。环境:仓颉 SDK 1.2.0。本文所有代码与输出均逐行实测。

weixin_41618057的博客 557

Mac上Ollama服务IP访问失败的3种修复方法(含永久生效配置)

本文详细介绍了Mac上Ollama服务IP访问失败的3种修复方法,包括临时环境变量覆盖、永久Shell配置修改及进阶排查技巧。重点解析了OLLAMA_HOST环境变量的配置原理,帮助开发者解决Connection refused问题,实现局域网IP访问Ollama服务的需求。

weixin_29209805的博客 210

信创环境下PageOffice文档控件适配与实践

信创适配做到文档控件这一层,拼的已经不是"有没有国产版本",而是同一个功能在两类终端上是否真的等价。等价的标准很具体:同一次点击能得到同样的结果,同一份公文能得到同样的版式,同一个项目不需要维护两套代码。这背后是三件并不轻松的工作:服务端用一套接口同时支撑两类终端,客户端把两种系统与四种芯片的安装包分发清楚,文档内核层由产品侧跟着 WPS 的版本走。浏览器这一层的压力,则被收进了产品自己的窗口里——升级节奏由产品掌握,不再交给运气。

zi_wu_xian的专栏 336

华为OD机试双机位C卷-开心消消乐(Py/Java/C/C++/Js/Go)

华为OD机试(机考)双机位C卷 【开心消消乐】,提供Java、C++、Python、Go、JavaScript源码实现,并提供完整思路讲解,以及在线OJ模拟做题。华为od机试 - 开心消消乐。

qq_45776114的博客 1514

详解RT-DETR网络结构/数据集获取/环境搭建/训练/推理/验证/导出/部署

本文给大家带来是利用RT-DETR模训练自己的数据集,RT-DETR是一种新提出的目标检测模型,它利用的自注意力机制来处理图像数据。不同于YOLO通过连续的卷积层直接对图像区域进行分析,RT-DETR采用Transformer架构中的自注意力机制,这允许模型更有效地理解图像中不同部分之间的关系。这种方法使得RT-DETR在处理图像中的复杂场景和多对象环境时,能够展现出更高的准确性和效率。此外,RT-DETR在保持高精度的同时,也针对实时处理进行了优化,使其适合需要快速响应的应用场景。

Snu77的博客 6万+

【从零理解 Spring AI · 12】MCP 的两种角色:做客户端还是做服务端

上一篇讲了 MCP 的概念:标准协议、三大角色、M+N 替代 M×N。

nice_lcj520的博客 614

Rerender A Video 技术浅析(四):跨帧约束

时间一致性是指在视频处理过程中,保持相邻帧之间内容、风格和运动的平滑过渡,避免出现视觉上的不连续性或伪影。时间一致性跨帧约束模块的主要目标是在视频增强、风格迁移等任务中,确保处理后的视频在时间维度上保持一致性和稳定性。该模块主要通过以下几种方式实现时间一致性:1.时序损失(Temporal Loss):最小化相邻帧之间的差异,确保帧间内容的平滑过渡。2.循环一致性损失(Cycle Consistency Loss):确保帧间转换的一致性,避免出现风格漂移。3.

m0_75253143的博客 1481

spring boot 4集成SQLLite,及其SQLLite的建库

spring boot 4集成SQLLite,及其SQLLite的建库

weixin_41463944的博客 230

jre9下载 jdk9

(Java SE Runtime Environment 9.0) 9.0u175 官方最新版 【x86|x64】

pscad IEEE标准系统搭建说明

pscad IEEE标准系统搭建说明,包含典型的IEEE 9节点、14节点、30节点、39节点和118节点系统。内含标准测试系统的原始数据和潮流结果。

pcl2启动器下载(Minecraft PCL2 启动器 最新版 安装与使用说明)

摘要:PCL2(Plain Craft Launcher 2)是一款面向 Minecraft 的第三方启动器,支持正式版与快照版本管理、模组与整合包安装、Java 运行时自动匹配,绿色免安装、双击即可运行。适合在 Windows 上玩单机整合包、需要多版本共存或离线启动的用户使用

2611_96675819的博客 225

jdk-8u144-linux-x64.tar.gz.

该资源为搭建Linux系统Java环境用,资源的后缀为tar.gz格式的压缩包

Java 集合容器高频面试题全解:HashMap 树化阈值、1.7 死循环与 ConcurrentHashMap 演进(2026 招聘 JD 真题复盘)

HashMap 树化阈值 8 的泊松分布依据、退化阈值 6 的防抖设计、JDK 1.7 头插成环死循环的排查与修复、1.8 尾插后为何仍线程不安全、ConcurrentHashMap 放弃分段锁的原因与 ForwardingNode 协作扩容、computeIfAbsent 死锁陷阱、大集合找重复的场景题选型,附三层追问链自测。题目来源为 38 期公开招聘 JD 样本与字节、拼多多、建行、美团、快手公开面经。

蒙眼过河 426

Outlook Express 6 (OE6) for Win7/Win8/Win10

英文版 Outlook Express6.0, 兼容Win7/Win10/WinXP,解压就可用。

spdlog 同步日志库使用详解

spdlog是一个轻量级 C++ 日志库,支持同步日志、异步日志、多线程日志、日志文件轮转和自定义日志格式。对于嵌入式 Linux 应用开发,我建议先使用。它可以帮我们完成:日志级别过滤。时间戳和线程 ID 输出。日志格式化。终端和文件输出。多线程安全写入。日志文件按大小或时间轮转。我们不需要自己实现互斥锁、文件写入、日志格式化和轮转等底层功能。

zengjiajun2006的博客 1124

JavaSE通关手册:数据类型与变量

代码无需额外处理,编译时编译器自动完成转换。

xys_678的博客 235

IDEA 简介:从零认识 IntelliJ IDEA

IDEA 全称,是由 JetBrains 公司开发的一款主流 Java 集成开发环境(IDE)。它集代码编辑、编译、调试、测试、版本控制、构建管理等功能于一体,被大量 Java 开发者视为日常开发的首选工具。所谓 IDE(Integrated Development Environment,集成开发环境),就是把写代码所需的各类工具整合到同一个界面中。相比只用文本编辑器加命令行编译,IDE 能显著减少重复操作,让开发者把精力集中在业务逻辑上。

ztI10的博客 184

Docker部署linkding:HTTPS与数据备份

部署私人书签库,除了让页面能够打开,还需要考虑几个实际问题:重建容器后数据是否保留、登录和保存是否正常、升级前怎样备份,以及出现 502 或 CSRF 错误时从哪里检查。本文使用 Docker Compose 部署 linkding,采用默认 SQLite 数据库,通过 Caddy 提供 HTTPS,并完成账户创建、数据持久化验证和备份。如果重建后账户或书签消失,应先检查是否换了项目目录、改了挂载路径,或者启动了另一套实例,不要急着重新初始化。遇到权限问题,应根据日志确认具体目录和运行用户,再调整权限。

tedcloud123的博客 193

动态代理两大流派:JDK 代理与子类代理

业务类想加日志,最直白的写法是侵入式修改: 问题很明显:每个方法都要改一遍,改一个业务要动十处。代理模式的解法是:调用方不直接依赖 ,而是依赖一个代理对象。代理对象长得跟目标一模一样,调用它 → 代理先执行增强逻辑 → 再转调真实对象。 关键在于:代理对象的类型是哪来的?这就是"动态"二字的含义:代理类在运行时才诞生。两个角色: 承载增强逻辑, 负责生成代理类。 组装代理并调用: 输出: 业务代码 一行没动,增强逻辑全在 里。这就是 AOP 的味道。 内部四步: 第 2 步 内部:先查 (同一个接口

Android的专栏 661

C++20协程怎么运行?原理与三大核心组件深度剖析

C++20协程是轻量级的无栈状态机,通过co_await、co_yield、co_return实现挂起与恢复,由Promise、协程句柄和Awaitable三大组件协同工作。协程与线程互补,适用于高效管理大量并发I/O任务,显著降低上下文切换开销。其核心在于编译器生成的状态机机制,需配合库(如cppcoro)使用。掌握Promise控制逻辑、句柄生命周期管理及Awaitable语义,是构建高性能异步程序的基础。

Lucis__的博客 335

c++ explicit关键字详解

explicit。

拒绝AI文,努力在AI时代写出感动人心的好文章 169

Teamcenter Java SOA 开发:连接、查询与保存

本文介绍如何通过 Java 调用 Teamcenter SOA 接口实现外部系统对接,涵盖连接登录、查询保存等核心操作。以最小闭环示例展示 Connection、Service、ModelObject 等关键组件的使用,强调错误处理与事务管理要点。梳理了 DataManagement、Query、File Management 等 API 模块分工,并结合“工作移交WebService”案例,说明幂等性设计与流程状态返回的重要性。适用于 Web 门户、ERP 集成等场景,建议批量操作用 bulk 接口优化性

软件工程师文艺 277

Java 项目实战:交友项目后台系统——网关统一鉴权与 B 端管理后台

本次改造通过引入SpringCloud Gateway实现网关统一鉴权与路由,新建mf-admin管理端复用C端域服务(Dubbo调用),实现管理员登录与用户管理四件查询。核心套路:网关白名单+双体系JWT(同工具不同payload)、管理端零直连业务库、分页形态区分(MySQL自动count/Mongo手动count)、浏览器端独立聚合。踩坑12条,附自检清单与后续改造方向,可复用于多角色后台系统。

Wang的专栏 60

TRingBuffer两端都能增删(快递站版)

TRingBuffer 是一个支持两端增删、下标访问且容量动态增长的环形双端队列。它通过无符号索引的永不归零设计,利用减法自动模运算实现空满判断与元素计数,避免了传统环形缓冲浪费格子的问题。内部以票号(索引)标记首尾,扩容时重排元素为连续存储,保证 O(1) 操作与高缓存效率。虽不线程安全,但其高效性使其成为游戏开发中事件队列、命令缓冲等场景的理想选择。

u013768914的博客 315
上一篇: CEG 2136 Arithmetic Logic Unit
下一篇: 【无标题】
vx___codinghelp
博客等级 码龄2年 778粉丝 101原创
评论
成就一亿技术人!
拼手气红包6.0元
还能输入1000个字符
 
 条评论被折叠 查看
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付:10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值