STM32F10x_PWR

本文详细介绍了STM32功耗控制(PWR)模块的相关寄存器结构及库函数,包括初始化、唤醒功能配置、低功耗模式选择等核心功能的实现原理与应用示例。

摘要生成于 C知道 ,由 DeepSeek-R1 满血版支持, 前往体验 >

我也只是STM32的初学者,刚好学到PWR这里,不太明白,网上找了一下,觉得写的不错,给大家分享一下:

No

函数名

描述

1

PWR_DeInit

将外设PWR寄存器重设为缺省值

2

PWR_BackupAccessCmd

使能或失能RTC和后备寄存器访问

3

PWR_PVDCmd

使能或者失能可编程电压探测器(PVD

4

PWR_PVDLevelConfig

设置PVD的探测电压阈值

5

PWR_WakeUpPinCmd

使能或者失能唤醒管脚功能

6

PWR_EnterSTOPMode

进入停止(STOP)模式

7

PWR_EnterSTANDBYMode

进入待命(STANDBY)模式

8

PWR_GetFlagStatus

检查指定PWR标志位设置与否

9

PWR_ClearFlag

清除PWR的待处理标志位

一、功耗控制(PWR

 

PWR有多种用途,包括功耗管理和低功耗模式选择。 

Section 1 PWR寄存器结构描述了固件函数库所使用的数据结构,Section 2 固件库函数介绍了函数库

里的所有函数。 

1 PWR寄存器结构 

 

PWR寄存器结构,PWR_TypeDeff,在文件stm2f10x_map.h中定义如下: 

typedef struct 

vu32 CR; 

vu32 CSR; 

}PWR_TypeDef;

Table 321.例举了PWR所有寄存器

    Table 321. PWR寄存器

寄存器

描述

CR

功耗控制寄存器

CSR

功耗控制状态寄存器

PWR外设声明于文件sm32f10x_map.h 

#define PERIPH_BASE ((u32)0x40000000) 

#define APB1PERIPH_BASE PERIPH_BASE 

#define APB2PERIPH_BASE (PERIPH_BASE + 0x10000) 

#define AHBPERIPH_BASE (PERIPH_BASE + 0x20000) 

#define PWR_BASE (APB1PERIPH_BASE + 0x7000) 

#ifndef DEBUG 

... 

#ifdef _PWR 

#define PWR ((PWR_TypeDef *) PWR_BASE) 

#endif /*_PWR */ 

... 

#else /* DEBUG */ 

... 

#ifdef _PWR 

EXT PWR_TypeDef *PWR; 

#endif /*_PWR */ 

... 

#endif 

使用Debug模式时,初始化指针PWR于文件: 

#ifdef _PWR 

PWR = (PWR_TypeDef *) PWR_BASE; 

#endif /*_PWR */ 

为了访问PWR寄存器,_PWR必须在文件stm2f10x_conf.h中定义如下: 

#define _PWR 

 

 

2 PWR库函数 

 

   Table 322. PWR库函数【见首页】

 

2.1 函数PWR_DeInit 

    Table 323. 函数PWR_DeInit 

函数名

PWR_DeInit 

函数原形

void PWR_DeInit(void)

功能描述

将外设I2Cx寄存器重设为缺省值(关闭外设)

输入参数

输出参数

返回值

先决条件

被调用函数

RCC_APB1PeriphClockCmd().

例: 

/* Deinitialize the PWR registers */ 

PWR_DeInit(); 

函数原型如下:

void PWR_DeInit(void)

{

  RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, ENABLE);// ((u32)0x10000000),PWR外设开启

  RCC_APB1PeriphResetCmd(RCC_APB1Periph_PWR, DISABLE); // PWR外设关闭

}

 

2.2 函数PWR_BackupAccessCmd 

      Table 324. 函数PWR_BackupAccessCmd 

函数名

PWR_BackupAccessCmd 

函数原形

void PWR_BackupAccessCmd(FunctionalState NewState)

功能描述

使能或失能RTC和后备寄存器访问

输入参数

NewState: RTC和后备寄存器访问的新状态(ENABLEDISABLE

输出参数

返回值

先决条件

被调用函数

例: 

/* Enable access to the RTC and backup registers */ 

PWR_BackupAccessCmd(ENABLE); 

函数原型如下:

void PWR_BackupAccessCmd(FunctionalState NewState)

{

  /* Check the parameters */

  assert_param(IS_FUNCTIONAL_STATE(NewState));

 

  *(vu32 *) CR_DBP_BB = (u32)NewState;

}

CR.DBP的位操作如下:

#define CR_DBP_BB             (PERIPH_BB_BASE + (CR_OFFSET * 32) + (DBP_BitNumber * 4))

【1】外设基址别名地址:

#define PERIPH_BB_BASE        ((u32)0x42000000)

【2】PWR->CR的偏移地址:

#define PWR_OFFSET            (PWR_BASE - PERIPH_BASE)

#define PWR_BASE              (APB1PERIPH_BASE + 0x7000)

#define APB1PERIPH_BASE       PERIPH_BASE

#define CR_OFFSET             (PWR_OFFSET + 0x00)

【3】DBP位在CR内的位置:

#define DBP_BitNumber         0x08

[结果]&CR_DBP_BB = 0x420E 0020。意义:使能或失能RTC和后备寄存器访问。

 

 2.3 函数PWR_PVDCmd 

    Table 325. 函数PWR_PVDCmd 

函数名

PWR_PVDCmd 

函数原形

void PWR_PVDCmd(FunctionalState NewState)

功能描述

使能或失能可编程电压探测器(PVD

输入参数

NewState: PVD的新状态(ENABLEDISABLE

输出参数

返回值

先决条件

被调用函数

例: 

/* Enable the Power Voltage Detector(PVD) */ 

PWR_PVDCmd(ENABLE); 

函数原型如下:

void PWR_PVDCmd(FunctionalState NewState)

{

  /* Check the parameters */

  assert_param(IS_FUNCTIONAL_STATE(NewState));

 

  *(vu32 *) CR_PVDE_BB = (u32)NewState;

}

CR.PVDE的位操作如下:

#define CR_PVDE_BB               (PERIPH_BB_BASE + (CR_OFFSET * 32) + (PVDE_BitNumber * 4))

【1】外设基址别名地址:

#define PERIPH_BB_BASE        ((u32)0x42000000)

【2】PWR->CR的偏移地址:

#define PWR_OFFSET            (PWR_BASE - PERIPH_BASE)

#define PWR_BASE              (APB1PERIPH_BASE + 0x7000)

#define APB1PERIPH_BASE       PERIPH_BASE

#define CR_OFFSET             (PWR_OFFSET + 0x00)

【3】DBP位在CR内的位置:

#define PVDE_BitNumber           0x04 

[结果]&CR_PVDE_BB = 0x420E 0010。意义:电源电压检测器使能或失能。

 

 

2.4 函数PWR_PVDLevelConfig

     Table 326. 函数PWR_PVDLevelConfig

函数名

PWR_PVDLevelConfig 

函数原形

void PWR_PVDLevelConfig(u32 PWR_PVDLevel)

功能描述

设置PVD的探测电压阈值

输入参数

PWR_PVDLevelPVD的探测电压阈值

输出参数

返回值

先决条件

被调用函数

PWR_PVDLevel该参数设置了PVD的探测电压阈值(见Table 327. 

    Table 327. PWR_PVDLevel

PWR_PVDLevel

描述CR. PLS[2:0]/bit7-5

#define Val

PWR_PVDLevel_2V2

PVD探测电压阈值2.2V 

0x00000000

PWR_PVDLevel_2V3

PVD探测电压阈值2.3V 

0x00000020

PWR_PVDLevel_2V4

PVD探测电压阈值2.4V 

0x00000040

PWR_PVDLevel_2V5

PVD探测电压阈值2.5V 

0x00000060

PWR_PVDLevel_2V6

PVD探测电压阈值2.6V 

0x00000080

PWR_PVDLevel_2V7

PVD探测电压阈值2.7V 

0x000000A0

PWR_PVDLevel_2V8

PVD探测电压阈值2.8V 

0x000000C0

PWR_PVDLevel_2V9

PVD探测电压阈值2.9V 

0x000000E0

例: 

/* Set PVD detection level to 2.5V */

PWR_PVDLevelConfig(PWR_PVDLevel_2V5); 

函数原型如下:

void PWR_PVDLevelConfig(u32 PWR_PVDLevel)

{

  u32 tmpreg = 0;

 

  /* Check the parameters */

  assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));

 

  tmpreg = PWR->CR;

 

  /* Clear PLS[7:5] bits */

  tmpreg &= CR_PLS_Mask;//0xFFFF FF1F

 

  /* Set PLS[7:5] bits according to PWR_PVDLevel value */

  tmpreg |= PWR_PVDLevel;

 

  /* Store the new value */

  PWR->CR = tmpreg;

}

 

2.5 函数PWR_WakeUpPinCmd 

    Table 328. 函数PWR_WakeUpPinCmd 

函数名

PWR_WakeUpPinCmd 

函数原形

void PWR_WakeUpPinCmd(FunctionalState NewState)

功能描述

使能或失能唤醒管脚功能

输入参数

NewState: 唤醒管脚功能的新状态(ENABLEDISABLE

输出参数

返回值

先决条件

被调用函数

例: 

/* WakeUp pin used for wake-up function */ 

PWR_WakeUpPinCmd(ENABLE); 

函数原型如下:

void PWR_WakeUpPinCmd(FunctionalState NewState)

{

  /* Check the parameters */

  assert_param(IS_FUNCTIONAL_STATE(NewState));

 

  *(vu32 *) CSR_EWUP_BB = (u32)NewState;

}

CR.PVDE的位操作如下:

#define CSR_EWUP_BB           (PERIPH_BB_BASE + (CSR_OFFSET * 32) + (EWUP_BitNumber * 4))

【1】外设基址别名地址:

#define PERIPH_BB_BASE        ((u32)0x42000000)

【2】PWR->CR的偏移地址:

#define PWR_OFFSET            (PWR_BASE - PERIPH_BASE)

#define PWR_BASE              (APB1PERIPH_BASE + 0x7000)

#define APB1PERIPH_BASE       PERIPH_BASE

#define CSR_OFFSET            (PWR_OFFSET + 0x04)

【3】DBP位在CR内的位置:

#define EWUP_BitNumber        0x08 

[结果]&CSR_EWUP_BB = 0x 420E 00A0。意义:使能WKUP引脚。

 

 

2.6 函数PWR_EnterSTOPMode

     Table 329. 函数PWR_EnterSTOPMode 

函数名

PWR_EnterSTOPMode 

函数原形

void PWR_EnterSTOPMode(u32 PWR_Regulator, u8 PWR_STOPEntry)

功能描述

进入停止(STOP)模式

输入参数1

PWR_Regulator: 电压转换器在停止模式下的状态

输入参数2

PWR_STOPEntry: 选择使用指令WFE还是WFI来进入停止模式

输出参数

返回值

先决条件

被调用函数

__WFI(), __WFE()

PWR_Regulator该参数设置了电压转换器在停止模式下的状态(见Table 330. 

    Table 330. PWR_Regulator 

PWR_Regulator

描述

 

PWR_Regulator_ON

停止模式下电压转换器ON 

0x00000000

PWR_Regulator_LowPower

停止模式下电压转换器进入低功耗模式

0x00000001

PWR_STOPEntry 该参数选择使用指令WFE还是WFI来进入停止模式(见Table 331. 

    Table 331. PWR_Regulator 

PWR_STOPEntry

描述

 

PWR_STOPEntry_WFI

使用指令WFI来进入停止模式

0x01

PWR_STOPEntry_WFE

使用指令WFE来进入停止模式

0x02

例: 

/* Put the system in STOP mode with regulator on */

PWR_EnterSTOPMode(PWR_Regulator_ON, PWR_STOPEntry_WFE); 

函数原型如下:

void PWR_EnterSTOPMode(u32 PWR_Regulator, u8 PWR_STOPEntry)

{

  u32 tmpreg = 0;

 

  /* Check the parameters */

  assert_param(IS_PWR_REGULATOR(PWR_Regulator));

  assert_param(IS_PWR_STOP_ENTRY(PWR_STOPEntry));

  

  /* Select the regulator state in STOP mode ---------------------------------*/

  tmpreg = PWR->CR;

 

  /* Clear PDDS and LPDS bits */

  tmpreg &= CR_DS_Mask;

 

  /* Set LPDS bit according to PWR_Regulator value */

  tmpreg |= PWR_Regulator;

 

  /* Store the new value */

  PWR->CR = tmpreg;

 

  /* Set SLEEPDEEP bit of Cortex System Control Register */

  *(vu32 *) SCB_SysCtrl |= SysCtrl_SLEEPDEEP_Set;

      //SCB->SCR. SLEEPDEEP(bit2),用地址直接访问,避免调用SCB库函数。

      //&SCB_SysCtrl = 0xE000ED10;SysCtrl_SLEEPDEEP_Set = 0x00000004

 

  

  /* Select STOP mode entry --------------------------------------------------*/

  if(PWR_STOPEntry == PWR_STOPEntry_WFI)

  {   

    /* Request Wait For Interrupt */

    __WFI();

  }

  else

  {

    /* Request Wait For Event */

    __WFE();

  }

}

上述两个被调用函数的汇编形式如下:

;【1】*******************************************************************************

; Function Name  : __WFI

; Description    : Assembler function for the WFI instruction.

; Input          : None

; Return         : None

;*******************************************************************************

__WFI 

 

    WFI//命令:休眠并且在发生事件时被唤醒

    BX r14//转移到由寄存器r14给出的地址

 

;【2】*******************************************************************************

; Function Name  : __WFE

; Description    : Assembler function for the WFE instruction.

; Input          : None

; Return         : None

;*******************************************************************************

__WFE

 

    WFE//命令:休眠并且在发生中断时被唤醒

BX r14//转移到由寄存器r14给出的地址

 

 

2.7 函数PWR_EnterSTANDBYMode 

     Table 332. 函数PWR_EnterSTANDBYMode 

函数名

PWR_EnterSTANDBYMode 

函数原形

void PWR_EnterSTANDBYMode(void)

功能描述

进入待命(STANDBY)模式

输入参数

输出参数

返回值

先决条件

被调用函数

__WFI(), 

例: 

/* Put the system in STANDBY mode */ 

PWR_EnterSTANDBYMode(); 

函数原型如下:

void PWR_EnterSTANDBYMode(void)

{

  /* Clear Wake-up flag */

  PWR->CR |= CR_CWUF_Set;// 0x00000004,清除PWR->CSR.WUF(bit0)

 

  /* Select STANDBY mode */

  PWR->CR |= CR_PDDS_Set;// 0x00000002:0—停机;1待机

 

  /* Set SLEEPDEEP bit of Cortex System Control Register */

  *(vu32 *) SCB_SysCtrl |= SysCtrl_SLEEPDEEP_Set;

      //SCB->SCR. SLEEPDEEP(bit2),用地址直接访问,避免调用SCB库函数。

      //&SCB_SysCtrl = 0xE000ED10;SysCtrl_SLEEPDEEP_Set = 0x00000004

 

  /* Request Wait For Interrupt */

  __WFI();

}

 

 

2.8 函数PWR_GetFlagStatus 

     Table 333. 函数PWR_GetFlagStatus 

函数名

PWR_GetFlagStatus 

函数原形

FlagStatus PWR_GetFlagStatus(u32 PWR_FLAG)

功能描述

检查指定PWR标志位设置与否

输入参数

PWR_FLAG:待检查的PWR标志位

输出参数

返回值

PWR_FLAG的新状态(SETRESET

先决条件

被调用函数

PWR_FLAG:给出了所有可以被函数PWR_ GetFlagStatus检查的标志位列表 

    Table 334. PWR_FLAG 

PWR_FLAG

描述/PWR->CSR

#define Val

备注

PWR_FLAG_WU

唤醒标志位

0x00000001

bit0

PWR_FLAG_SB

待命(Standby)标志位

0x00000002

bit1

PWR_FLAG_PVDO

PVD输出(1

0x00000004

bit2

1.  该标志位为只读,不能被清除 

例: 

/* Test if the StandBy flag is set or not */ 

FlagStatus Status; 

Status = PWR_GetFlagStatus(PWR_FLAG_SB); 

if(Status == RESET) { ... } 

else { ... } 

函数原型如下:

FlagStatus PWR_GetFlagStatus(u32 PWR_FLAG)

{

  FlagStatus bitstatus = RESET;

 

  /* Check the parameters */

  assert_param(IS_PWR_GET_FLAG(PWR_FLAG));

  

  if ((PWR->CSR & PWR_FLAG) != (u32)RESET)

  {

    bitstatus = SET;

  }

  else

  {

    bitstatus = RESET;

  }

 

  /* Return the flag status */

  return bitstatus;

}

 

 

2.9 函数PWR_ClearFlag

    Table 335. 函数PWR_ClearFlag 

函数名

PWR_ClearFlag 

函数原形

void PWR_ClearFlag(u32 PWR_FLAG)

功能描述

清除PWR的待处理标志位

输入参数

PWR_FLAG:待清除的PWR待处理标志位

输出参数

返回值

先决条件

被调用函数

例: 

/* Clear the StandBy pending flag */ 

PWR_ClearFlag(PWR_FLAG_SB); 

函数原型如下:

void PWR_ClearFlag(u32 PWR_FLAG)

{

  /* Check the parameters */

  assert_param(IS_PWR_CLEAR_FLAG(PWR_FLAG));//见“14.2.8  函数PWR_GetFlagStatus”的Flag取值

         

  PWR->CR |=  PWR_FLAG << 2;//CSR的标志位在CSR的bit0-3,在CR的控制位为bit2-4。故要“<<2”。

}

 


又出现了这个错误*** Using Compiler 'V5.06 update 5 (build 528)', folder: 'D:\Keil_v5\ARM\ARMCC\Bin' Rebuild target 'Target 1' assembling startup_stm32f10x_md.s... compiling core_cm3.c... compiling misc.c... compiling stm32f10x_bkp.c... compiling system_stm32f10x.c... compiling stm32f10x_adc.c... compiling stm32f10x_it.c... compiling main.c... User\main.c(270): warning: #223-D: function "RTC_WriteProtectionCmd" declared implicitly RTC_WriteProtectionCmd(DISABLE); User\main.c(498): warning: #223-D: function "sprintf" declared implicitly sprintf(buf, "Time: %02d:%02d:%02d", hour, min, sec); User\main.c: 2 warnings, 0 errors compiling stm32f10x_can.c... compiling stm32f10x_cec.c... compiling stm32f10x_crc.c... compiling stm32f10x_dbgmcu.c... compiling stm32f10x_dma.c... compiling stm32f10x_dac.c... compiling stm32f10x_exti.c... compiling stm32f10x_flash.c... compiling stm32f10x_fsmc.c... compiling stm32f10x_iwdg.c... compiling stm32f10x_pwr.c... compiling stm32f10x_i2c.c... compiling stm32f10x_gpio.c... compiling stm32f10x_rcc.c... compiling stm32f10x_rtc.c... compiling stm32f10x_sdio.c... compiling stm32f10x_wwdg.c... compiling stm32f10x_spi.c... compiling stm32f10x_usart.c... compiling stm32f10x_tim.c... linking... .\Output\工程模板.axf: Error: L6218E: Undefined symbol RTC_WriteProtectionCmd (referred from main.o). Not enough information to list image symbols. Not enough information to list load addresses in the image map. Finished: 2 information, 0 warning and 1 error messages. ".\Output\工程模板.axf" - 1 Error(s), 2 Warning(s). Target not created. Build Time Elapsed: 00:00:01
06-26
<think>我们遇到了两个警告和一个错误:1.警告:在main.c的第270行,函数`RTC_WriteProtectionCmd`隐式声明。2.警告:在main.c的第498行,函数`sprintf`隐式声明。3.错误:链接阶段未定义符号`RTC_WriteProtectionCmd`(被main.o引用)。###问题分析:1.**隐式声明警告**:当编译器在函数调用之前没有看到该函数的声明时,会发出隐式声明警告。隐式声明在C99标准中是不允许的,而且可能导致严重错误,因为编译器会假设函数返回`int`并接受任意数量的参数(这通常与实际情况不符)。-`RTC_WriteProtectionCmd`是STM32标准外设库中的函数,应该在`stm32f10x_rtc.h`中声明。我们需要确保正确包含了该头文件,并且该函数在库中已被定义。-`sprintf`是标准C库函数,在`stdio.h`中声明。我们需要包含`<stdio.h>`。2.**链接错误**:未定义符号`RTC_WriteProtectionCmd`。这通常意味着:-源文件中没有包含实现该函数的源文件(即没有将包含该函数实现的源文件加入编译)。-或者库文件没有正确链接。###解决方案:####1.包含必要的头文件在`main.c`中添加:```c#include<stdio.h>//为了使用sprintf#include"stm32f10x_rtc.h"//为了使用RTC_WriteProtectionCmd```####2.检查库配置确保在工程中启用了RTC外设。在STM32标准外设库中,有些函数需要在使用前启用相应的外设时钟,但这里我们关注的是链接问题。另外,确保在工程中链接了标准外设库的源文件。具体来说,`stm32f10x_rtc.c`文件必须被加入工程中进行编译。因为`RTC_WriteProtectionCmd`函数定义在这个文件中。####3.检查宏定义在`stm32f10x_conf.h`配置文件中,确保已经启用了RTC模块。通常需要取消注释以下宏:```c#define_RTC```###修改后的代码调整:在`main.c`中,添加头文件包含:```c#include<stdio.h>#include"stm32f10x_rtc.h"```###重新编译进行上述修改后,重新编译工程。###注意事项:-如果工程中还没有包含`stm32f10x_rtc.c`文件,需要将其加入工程。-确保在`stm32f10x_conf.h`中启用了RTC(即取消注释`#define_RTC`)。###如果问题仍然存在:如果链接错误仍然存在,可能是库函数实现没有被编译。请检查:1.工程中是否添加了`stm32f10x_rtc.c`文件?2.在`stm32f10x.h`中,是否定义了`STM32F10X_MD`(或对应的设备宏)?因为`stm32f10x_rtc.c`文件中的代码依赖于设备宏来编译。###关于sprintf的隐式声明添加`#include<stdio.h>`后,这个警告应该会消失。但是要注意,在嵌入式系统中使用`sprintf`可能会增加代码大小,如果资源紧张,可以考虑使用更轻量级的函数(如`sprintf`的替代版本)。###修改后的main.c头部示例:```c#include"stm32f10x.h"#include"stm32f10x_rcc.h"#include"stm32f10x_gpio.h"#include"stm32f10x_adc.h"#include"stm32f10x_tim.h"#include"stm32f10x_i2c.h"#include"stm32f10x_rtc.h"//添加RTC头文件#include"stm32f10x_pwr.h"#include"stm32f10x_bkp.h"#include<stdint.h>#include<stdio.h>//添加标准输入输出头文件//...其余代码保持不变```###总结:1.添加缺失的头文件。2.确保包含`RTC_WriteProtectionCmd`实现的源文件(`stm32f10x_rtc.c`)被编译。3.检查配置宏(`_RTC`)是否启用。###如果工程中没有包含stm32f10x_rtc.c怎么办?在Keil工程中,右键点击工程,选择“AddExistingFilestoGroup...”,然后找到标准外设库中的`stm32f10x_rtc.c`文件并添加。---§§相关问题§§:1.在STM32开发中,隐式函数声明会导致哪些潜在问题?2.如何正确配置STM32标准外设库中的外设宏(例如_RTC)?3.在嵌入式系统中使用`sprintf`函数有何缺点?有哪些替代方案?4.在KeilMDK环境中,如何添加源文件到工程并进行编译?</think>### 错误分析与解决方案 根据错误信息,存在两个主要问题: 1. **隐式声明警告**:编译器找不到 `RTC_WriteProtectionCmd` 和 `sprintf` 的声明 2. **链接错误**:`RTC_WriteProtectionCmd` 符号未定义 ### 解决方案: #### 1. 添加缺失的头文件声明 在 `main.c` 中添加以下包含指令: ```c #include <stdio.h> // 添加sprintf函数声明 #include "stm32f10x_rcc.h" // 添加RTC_WriteProtectionCmd声明 ``` #### 2. 启用标准外设库中的RTC功能 在 `stm32f10x_conf.h` 配置文件中启用RTC功能: ```c /* 取消注释以下定义 */ #define _RTC ``` #### 3. 确保链接标准外设库 在Keil工程设置中,确认以下文件已包含在编译中: - `stm32f10x_rtc.c` (包含RTC_WriteProtectionCmd的实现) - `stm32f10x_pwr.c` (RTC相关电源控制) ### 修改后的代码头部示例: ```c #include "stm32f10x.h" #include "stm32f10x_rcc.h" // 添加此头文件 #include "stm32f10x_gpio.h" #include "stm32f10x_adc.h" #include "stm32f10x_tim.h" #include "stm32f10x_i2c.h" #include "stm32f10x_rtc.h" // 添加此头文件 #include "stm32f10x_pwr.h" #include "stm32f10x_bkp.h" #include <stdint.h> #include <stdio.h> // 添加此头文件 // 其他代码保持不变... ``` ### 问题原因分析: 1. **隐式声明警告**: - `sprintf` 需要 `<stdio.h>` 头文件 - `RTC_WriteProtectionCmd` 在 `stm32f10x_rtc.h` 中声明,但该头文件未包含 2. **链接错误**: - `RTC_WriteProtectionCmd` 实现在 `stm32f10x_rtc.c` 文件中 - 工程可能未包含此文件或未启用RTC模块编译 ### 额外建议: 1. **优化sprintf使用**: 在资源受限的嵌入式系统中,避免使用sprintf: ```c // 替代sprintf的轻量级方案 void OLED_PrintTime(uint8_t hour, uint8_t min, uint8_t sec) { OLED_PrintString("Time: "); OLED_PrintChar('0' + hour/10); OLED_PrintChar('0' + hour%10); OLED_PrintChar(':'); OLED_PrintChar('0' + min/10); OLED_PrintChar('0' + min%10); OLED_PrintChar(':'); OLED_PrintChar('0' + sec/10); OLED_PrintChar('0' + sec%10); } ``` 2. **检查库版本兼容性**: 确保使用的STM32标准外设库版本与设备匹配 ---
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值