飘雪冰峰的博客

ACL 基本配置OSPF 配置这里以 R3 为例，展示 ospf 的配置。在 AR3260 系列路由器中，可以正常配置# R3 IP配置<Huawei>system-view [Huawei]sysname R3[R3]q <R3>undo terminal monitor # 屏蔽 terminal 端的打印信息Info: Current terminal monitor is off.<R3> <R3>system-view En

DHCP 配置实验配置命令在 R1 路由器上完成 DHCP服务的配置# 配置基于全局的 DHCP<Huawei>system-view [Huawei]sysname R1[R1]dhcp enable [R1]ip pool testdhcpInfo:It's successful to create an IP address pool.[R1-ip-pool-testdhcp]network 192.168.1.0[R1-ip-pool-testdhcp]lease

OSPF 基本实验配置命令ospf 基本配置命令# R3 ospf 配置[R3]ospf 1[R3-ospf-1]area 0[R3-ospf-1-area-0.0.0.0]network 192.168.4.0 0.0.0.255[R3-ospf-1-area-0.0.0.0]network 192.168.3.0 0.0.0.255R1# R1 配置<Huawei>system-view Enter system view, return user view wit

交换机telnet配置网络拓扑配置命令查看交换机mac地址表# 查看 交换机mac 地址表[sw1]display mac-address 配置交换机的远程管理IP地址<Huawei>system-view [Huawei]sysname sw1#配置交换机的远程管理IP地址[sw1]interface Vlanif 1[sw1-Vlanif1]ip address 192.168.1.1 255.255.255.0[sw1-Vlanif1]quit[sw1]ip

交换机stp基本配置stp 基本配置<Huawei>system-view Enter system view, return user view with Ctrl+Z.[Huawei]sysname sw2[sw2]stp enable [sw2]stp mode stp [sw2]stp piority 8192stp 信息查看sw1[sw1]display stp brief MSTID Port Role

路由器 telnet配置基于password 的远程登录R1<R1>system-view [R1]interface GigabitEthernet 0/0/0[R1-GigabitEthernet0/0/0]ip address 10.0.12.1 24[R1-GigabitEthernet0/0/0]q[R1]telnet server enable # 开启telnetInfo: The Telnet server has been enabled.[R1]

ipv6 静态路由配置R1 配置<Huawei>system-view Enter system view, return user view with Ctrl+Z.[Huawei]sysname R1[R1]ipv6 # 全局使能 ipv6[R1]interface GigabitEthernet 0/0/0[R1-GigabitEthernet0/0/0]ipv6 enable [R1-GigabitEthernet0/0/0]ipv6 address 2001::

单臂路由网路拓扑配置命令配置子接口[r1-GigabitEthernet0/0/0.2]int g0/0/0.3[r1-GigabitEthernet0/0/0.3]ip address 192.168.3.1 24[r1-GigabitEthernet0/0/0.3]vlan-type dot1q 30关闭串口消息打印关闭串口消息打印[Huawei]undo info-center enable Info: Information center is disabled.# 简