Design Space Exploration
Solutions to project assignments are to be developed within your group, without col laboration with other groups. However, as the projects in this class require the use of
software tools and frameworks that students may have uneven prior familiarity with, dis cussion and assistance among students in gaining expertise with these software tools con stitutes acceptable behavior. Note that this assistance and discussion cannot include
the sharing of access to any code produced in solution to the project assignments. In
order to avoid potential ambiguity in what constitutes ”code produced in solution to the
project assignment,” students wishing to aid their peers with auxiliary supporting scripts,
mechanisms, or examples are directed to pass any such artifacts to the course staff for vet ting and possible inclusion on project-specific FAQs rather than share it with their peers
directly.
In this project, you are going to use SimpleScalar as the evaluation engine to perform
a design space exploration, using the provided framework code, over a 18-dimensional
processor pipeline and memory hierarchy design space (some of these dimensions are not
independent). You will use a 5-benchmark suite as the workload.
1. Project Goal
Your assignment is to, with an evaluation count limit of 1000 design points, explore the
design space in order to select the best performing design under a set of two different
optimization functions. These include:
1. The “best” performing overall design (in term of the geometric mean of normal ized execution time normalized across all benchmarks)
2. The most energy-efficient design (as measured by the lowest geometric mean of
normalized energy-delay product [units of energy delay product are joule-seconds]
across all benchmarks)
2. Background
2.1. SimpleScalar
SimpleScalar is an architectural simulator which enables a study of how different pro cessor and memory system parameters affect performance and energy efficiency. The
simulator accepts a set of system design parameters and an executable (workload) to run
on the described system. A wide range of system statistics are recorded by the simulator
as the executable runs on the simulated system. Once the framework in this project is
setup, interested readers can have a look at one of the log files in rawProjectOutputData
folder to view SimpleScalar output.
This project heavily uses SimpleScalar but most of the interface is abstracted out by a
simpler framework interface. Nevertheless, you can refer to this SimpleScalar guide for
details about parameters passed to SimpleScalar.
2.2. Design Space Exploration
Given a set of design parameters, Design Space Exploration (DSE) involves probing var ious design points to find the most suitable design to meet required goals. Follow this
quick reading about DSE before moving ahead.
DSE can be performed for different design goals. For example, one DSE may want to
find the best performing design whereas another DSE may be aimed at finding the most
energy efficient design. A more complex DSE may look for the best performing design
given a fixed energy budget.
An exhaustive DSE simply tries out all possible combinations of parameter values to
find the absolute best design. However, as the size of design space increases this approach
quickly becomes infeasible. Consider a 10-dimensional design space with 5 possible
values for each parameter and 2 minutes simulation time to evaluate a given design point;
an exhaustive search will take 5
10 ∗ 2min ≈ 37years.
A more intelligent DSE employs heuristics to intelligently prune down the design space
and to prioritize evaluation of more reasonable design points first. If the assumptions
employed by the heuristics are correct, the DSE will still result in the best design. On the
other hand. with a set of reasonably justified assumptions a heuristic can result in a “good
enough” design point.
2.3. Energy-Delay Product
Energy-Delay Product (EDP) is a metric which consolidates both performance and energy
efficiency.
EDP = total execution energy * execution time
Design A takes 100pJ to process an image in 100ms, EDP = 10000 units. Design B
takes 80pJ to process an image in 2000ms, EDP = 160000. Design A is clearly more
energy efficient, but it performs poorly as it incurs more execution time. EDP enables a
more holistic design comparison.
3. Our Heuristic
We define OurHeuristic as follows:
1. Design space dimensions can be labelled as either explored and unexplored.
2. Initially all dimensions are unexplored
3. Choose an unexplored dimension, exit if all dimensions are explored
3.1. Evaluate all possible design points by changing the value of this dimension
only
2
3.2. Fix value of this dimension by selecting the best design so far (consider
DSE goal)
3.3. Mark this dimension as explored
4. Go to step 3.
You should choose an unexplored dimension in step 3 based on your PSU ID Numbers
of students in the group, as follows.
DSE dimensions can be categorized in four major classes as follows:
1. Branch predictor (BP) configurations (i.e. branchsettings, ras, btb)
2. Cache configurations (i.e. {l1, ul2}block, {dl1, il1, ul2}sets, {dl1, il1, ul2}assoc)
3. Core configurations (i.e. width, scheduling)
4. Floating Point Unit (FPU) configuration (i.e. fpwidth)
Based on your ID numbers, you should calculate
( ID Number 1 + ID Number 2) mod 24
and then you should look at the Table 1 and start from the first category in the correspond ing row, and then second category, and so on.
For example, if your ID numbers are 9123456789 and 9111111111, the remainder
of its sum’s division by 24 is 12 and you should explore Core configs first, then BP
configs, then Cache configs, and then FPU configs at last.
Please note that the current implemented heuristic in generateNextConfigurationPro posal function is a simple heuristic as follows and you should extend it as explained
above. Current implementation starts from the leftmost dimension and explores all pos sible options for this dimension, and then goes to the next dimension until the rightmost
dimension.
4. Logistics
The set of possible points within the design space to be considered are constrained by the
provided shell script wrapper runprojectsuite.sh. All allowed configuration parameters
for each dimension of the design space are briefly described in the provided shell script.
runprojectsuite.sh shell script takes 18 integer arguments, one for each configuration
dimension, which expresses the index of the selected parameter for each dimension. All
reported results should be normalized against a baseline design with configuration param eters which already hard-coded in the framework.
Note that not all possible parameter settings represent a valid combination. One
of your tasks will be to write a configuration validation function based upon restrictions
described later in this document. Further, note that this design space is too large to effi-
ciently search in an exhaustive manner. Hence, a heuristic will be developed to specify an
order in which the design space will be explored.
The framework code will evaluate a fixed number of design points per run. This pa rameter cannot be changed. The key part of your task in this project is to implement
a heuristic search function that selects the next design point to consider, given either a
3
Table 1. Exploration Orders based on PSU ID.
( ID Number Sum) mod 24 1
st 2
nd 3
rd 4
th
0 BP Cache Core FPU
1 BP Cache FPU Core
2 BP Core Cache FPU
3 BP Core FPU Cache
4 BP FPU Cache Core
5 BP FPU Core Cache
6 Cache BP Core FPU
7 Cache BP FPU Core
8 Cache Core BP FPU
9 Cache Core FPU BP
10 Cache FPU BP Core
11 Cache FPU Core BP
12 Core BP Cache FPU
13 Core BP FPU Cache
14 Core Cache BP FPU
15 Core Cache FPU BP
16 Core FPU BP Cache
17 Core FPU Cache BP
18 FPU BP Cache Core
19 FPU BP Core Cache
20 FPU Cache BP Core
21 FPU Cache Core BP
22 FPU Core BP Cache
23 FPU Core Cache BP
performance, or an energy efficiency goal. Note that the framework code must be run
once for each of the optimization function options.
The framework, as given, provides functionality to enforce several, but by no means all,
of the validation constraints. It is your job to implement validation functions to enforce
constraints described throughout this document.
5. Framework
A sample run to use the provided framework can look something like this:
Extract project files archive and navigate to
project directory.
make clean
make
./DSE performance
Different components of the framework are invoked in the following order:
DSE (project binary) → runprojectsuite.sh (shell script) → SimpleScalar
4
DSE binary invokes runprojectsuite.sh script which in turn invokes SimpleScalar
simulator with appropriate arguments. Several log files are generated in project directory
on every invocation.
6. Anticipated Steps
These steps can serve as a high-level guideline to aid you during the project:
1. Enter ID in YOURCODEHERE.c.
2. Setup provided framework to get a set of results using the provided “unintelligent”
heuristic.
3. Implement validateConfiguration and generateCacheLatencyParams functions.
4. Implement OurHeuristic in generateNextConfigurationProposal for both opti mization goals (a well performing design and an energy efficient design)
5. Complete Report
7. Submission Requirements
1. Project report
2. Code implementations of missing or stub functions within the provided framework
7.1. Project Report
Your report must at conform to requirements listed in Appendix A. This report, data
contained within and their analysis will be the primary means of assessing this project.
7.2. Code Implementations
You will submit the source files (Makefile, runprojectsuite.sh, *.cpp and *.h) of your
implementation as a single tar archive for an audit of your implementation efforts. Ensure
that your code compiles on CSE machines without errors. You can make changes to
framework if you conclude that they are required. The following commands will be used
to compile and execute your code (followed by analysis of generated log files):
# Extract project files archive and navigate to
project directory.
make
./DSE performance
./DSE energy
Please note that running each of exploration modes could take more than one hour, so
please start as soon as possible so you could finish by the deadline.
8. Modeling Considerations
The Instruction Count (IC) for each benchmark is a constant. Thus, for performance, you
will be trying to optimize Instructions Per Cycle (IPC) and the Clock Cycle (CC) time.
Unless specified otherwise, the following modeling consideration have already been
implemented in the framework to calculate EDP. However, the provided information
may be used for explaining design space exploration results.
5
8.1. Clock Cycle Time
We will use the following very simplistic model for clock cycle time: The clock cycle
time is determined by the fetch width, number of floating-point units, and whether the
machine is in-order, or dynamic as follows:
• Dynamic, fetch width = 1: 115 ps + FPU delay
• In-order, fetch width = 1:100 ps + FPU delay
• Dynamic, fetch width = 2: 125 ps + FPU delay
• In-order, fetch width = 2: 120 ps + FPU delay
• Dynamic, fetch width = 4: 150 ps + FPU delay
• In-order, fetch width = 4: 140 ps + FPU delay
• Dynamic, fetch width = 8: 175 ps + FPU delay
• In-order, fetch width = 8: 165 ps + FPU delay
FPU delay is determined by the number of floating-point units as follows:
• count = 1: 5ps
• count = 2: 10ps
• count = 4: 20ps
• count = 8: 40ps
8.2. Power & Energy
8.2.1. Core Leakage Power
• Dynamic, fetch width = 1: 1.5 mW
• In-order, fetch width = 1: 1 mW
• Dynamic, fetch width = 2: 2 mW
• In-order, fetch width = 2: 1.5 mW
• Dynamic, fetch width = 4: 8 mW
• In-order, fetch width = 4: 7 mW
• Dynamic, fetch width = 8: 32 mW
• In-order, fetch width = 8: 30 mW
8.2.2. Floating Point Unit Power
• count = 1: 0.25 mW
• count = 2: 0.50 mW
• count = 4: 1 mW
• count = 8: 2 mW
8.2.3. Cache and Memory
Following list comprises tuples of format: [cache size or memory, access energy(pJ),
leakage/refresh power(mW)]
• 8KB: 20pJ, 0.125mW
• 16KB: 28pJ, 0.25mW
6
• 32KB: 40pJ, 0.5mW
• 64KB: 56pJ, 1mW
• 128KB: 80pJ, 2mW
• 256KB: 112pJ, 4mW
• 512KB: 160pJ, 8mW
• 1024KB: 224pJ, 16mW
• 2048KB: 360pJ, 32mW
• Main Memory: 2nJ, 512mW
8.2.4. Energy per Committed Instruction
• Dynamic, fetch width = 1: 10pJ
• In-order, fetch width = 1: 8pJ
• Dynamic, fetch width = 2: 12pJ
• In-order, fetch width = 2: 10pJ
• Dynamic, fetch width = 4: 18pJ
• In-order, fetch width = 4: 14pJ
• Dynamic, fetch width = 8: 27pJ
• In-order, fetch width = 8: 20pJ
8.3. Validation Constraints
You must implement these validation constraints in your code. Specifically, validate Configuration and generateCacheLatencyParams must be implemented properly.
1. The il1 (L1 instruction cache) block size must be at least the ifq (instruction fetch
queue) size (e.g., for the baseline machine the ifqsize is set to 1 word (8B) then
the il1 block size should be at least 8B). The dl1 (L1 data cache) should have the
same block size as your il1.
2. The ul2 (unified L2 cache) block size must be at least twice your il1 (and dl1)
block size with a maximum block size of 128B. Your ul2 must be at least twice as
large as il1+dl1 in order to be inclusive.
3. il1 size and dl1 size: Minimum = 2 KB; Maximum = 64 KB
4. ul2 size: Minimum = 32 KB; Maximum = 1 MB
5. The il1 sizes and il1 latencies are linked as follows (the same linkages hold for the
dl1 size and dl1 latency):
(a) il1 = 2 KB means il1lat = 1
(b) il1 = 4 KB means il1lat = 2
(c) il1 = 8 KB means il1lat = 3
(d) il1 = 16 KB means il1lat = 4
(e) il1 = 32 KB means il1lat = 5
(f) il1 = 64 KB means il1lat = 6
(g) The above are for direct mapped caches. For 2-way set associative add 1
additional cycle of latency to each of the above; for 4-way add 2 additional
cycles; for 8-way add 3 additional cycles.
6. The ul2 sizes and ul2 latencies are linked as follows:
(a) ul2 = 32 KB means ul2lat = 5
(b) ul2 = 64 KB means ul2lat = 6
7
(c) ul2 = 128 KB means ul2lat = 7
(d) ul2 = 256 KB means ul2lat = 8
(e) ul2 = 512 KB means ul2 lat = 9
(f) ul2 = 1024 KB (1 MB) means ul2lat = 10
(g) The above are for direct mapped caches. For 2-way set associative add 1
additional cycle of latency to each of the above; for 4-way add 2 additional
cycles; for 8-way add 3 additional cycles; for 16-way add 4 additional
cycles.
8.4. Miscellaneous Constraints
These constraints have already been specified in the framework. Have a look at Sim pleScalar invocation command in runprojectsuite.sh for an exhaustive list of specified
parameters. Moreover, any parameter not specified in runprojectsuite.sh will default to
SimpleScalar default settings.
• mplat is fixed at 3
• fetch:speed is fixed at 1
• ifqsize can be set to a maximum of 8 words (64B)
• decode:width and issue:width equal to your fetch:ifqsize
• mem:width is fixed at 8B (memory bus width)
• memport if fixed at 1
• mem:lat is fixed at 51 + 7 cycles for 8 word
8
Appendices
A. Project Report Minimum Requirements
Your report must at least answer the following prompts in the exact same order.
1. Describe in 100 words or less how the provided framework and its components
enable a design space exploration.
2. List the design point chosen by your DSE.
3. Fill out the following table as detailed below.
4. Plots as detailed below
5. Describe a more sophisticated heuristic which you expect will perform design
space exploration (limited by 1000 design points) more effectively to find a better
performing design (with respect to execution time).
6. Elaborate on any 2 new insights you gained while working on this project.
7. List of additional resources used (optional)
8. Additional information or comments (optional)
A.1. Table
In each cell specify the parameter value followed by why this value guided the DSE
closer to your optimization goal (for example: more ALUs allow extraction of more ILP
and increase performance). Make sure the parameters are in the exact order as they appear
in runprojectsuite.sh
Parameter Performance EDP
Param1 (i.e. width) Value = Value =
Why = Why =
Param2 (i.e. scheduling) Value = Value =
Why = Why =
... ...
ParamN Value = Value =
Why = Why =
A.2. Plots
The report should include the following four plots:
A. Line plot of normalized geomean execution time (y axis) for each considered de sign point vs. number of designs considered (x axis)
B. Line plot of normalized geomean of energy-delay product (y axis) vs number of
designs considered
C. Bar chart showing normalized per-benchmark execution time and geomean nor malized execution time for the best performing design
D. Bar chart showing per-benchmark normalized energy-delay product and geomean
normalized energy delay product for the most energy-efficient design found
These four plots must be labelled in your report corresponding exactly to num bering in the list above. Furthermore, axis in the plots should be properly labelled.
9
A.3. Other Guidelines
For clarity in the written report, when listing the best design points, please do not represent
them in terms of their index representations (e.g. 1 0 0 5 2 ...) and instead describe the
actual value used for each dimension in a table or similar presentation.
Points will also be assigned for following the guidelines and adhering to appropriate
levels of clarity, and style (and spelling, grammar, etc.) for a technical document.
10
B. Project FAQs
Q: What are the column headers for the .log file?
A: normalized EDP, normalized Execution time, absolute EDP, absolute Execution
time. The writes to both the .best and .log files are generated near the end of main.
Q: What are the column headers for the .best file?
A: Headers differ by line:
Line 1 headers: bestEDPconfig, normalized EDP of bestEDPconfig, normalized Exe cution time of bestEDPconfig, absolute EDP of bestEDPconfig, absolute Execution time
of bestEDPconfig, absolute EDP of Bench 0 on bestEDPconfig, normalized EDP of Bench
0 on bestEDPconfig, absolute EDP of Bench 1 on bestEDPconfig, normalized EDP of
Bench 1 on bestEDPconfig, absolute EDP of Bench 2 on bestEDPconfig, normalized
EDP of Bench 2 on bestEDPconfig, absolute EDP of Bench 3 on bestEDPconfig, nor malized EDP of Bench 3 on bestEDPconfig, absolute EDP of Bench 4 on bestEDPconfig,
normalized EDP of Bench 4 on bestEDPconfig
Line 2 headers: bestTimeconfig, normalized EDP of bestTimeconfig, normalized Ex ecution time of bestTimeconfig, absolute EDP of bestTimeconfig, absolute Execution
time of bestTimeconfig, absolute Time of Bench 0 on bestTimeconfig, normalized Time
of Bench 0 on bestTimeconfig, absolute Time of Bench 1 on bestTimeconfig, normal ized Time of Bench 1 on bestTimeconfig, absolute Time of Bench 2 on bestTimeconfig,
normalized Time of Bench 2 on bestTimeconfig, absolute Time of Bench 3 on bestTime config, normalized Time of Bench 3 on bestTimeconfig, absolute Time of Bench 4 on
bestTimeconfig, normalized Time of Bench 4 on bestTimeconfig
Q: Why are there only 18 configuration parameters when SimpleScalar (and the
project specification) list so many more?
A: There are 18 configuration variables, and more derived settings from those 18 con-
figuration variables, and still more settings that are fixed as constant (e.g. MPLAT). Given
the block size (set independently), associativity (set independently), and number of sets
(set independently), you can determine total cache size for the L1D and I caches and then
validate if the latency for that cache (set independently) is set correctly.
Q: What’s a quota error, why are half my output files empty, and why can’t I
make new files anymore?
A: It means you are out of disk space. Each run of this program produces a large num ber of intermediate output files for the evaluated design points. These are kept to speed
up subsequent evaluations of the same design point in future runs as a means of reducing
debugging/heuristic development time. Consider cleaning out your browser caches if you
are low on disk quota before performing a project run.
相关推荐
数字芯片设计中的逻辑综合:从RTL到门级网表的优化引擎
逻辑综合是数字芯片前端设计流程中的核心技术,负责将高层次硬件描述语言(如Verilog)转化为特定工艺下的门级网表。其核心原理是在满足时序、面积、功耗等约束条件下,通过算法对电路结构进行优化与重组。这一过程的技术价值在于,它直接决定了芯片的物理实现质量与性能,是连接设计与制造的桥梁。在应用场景上,逻辑综合广泛应用于ASIC和FPGA设计流程中,是确保芯片功能正确且满足性能指标的关键步骤。本文聚焦于Synopsys Design Compiler这一行业标准工具,深入解析其库文件管理、约束设置、时序分析等核心
Design Space Exploration (DSE)
Design Space Exploration (DSE) refers to systematic analysis and pruning of unwanted design points based on parameters of interest. While the term DSE can apply to any kind of system, we refer to elec...
Mythos:首个具备自主攻防闭环能力的AI安全模型
AI安全正从‘用AI辅助安全’迈向‘AI即攻击面’的新阶段。自主攻防闭环能力指模型无需人工提示或预设工具,即可完成目标分析、漏洞识别、利用链构造与执行验证的全周期推理。其技术基础在于状态空间探索与推理时计算扩展,突破传统模式匹配局限,实现对软件运行时行为的深度建模。该能力已实测应用于内核级零日挖掘、微服务RCE自动化生成等高阶场景,推动DevSecOps流程重构与防御体系升维。本文聚焦Claude Mythos所代表的这一代通用安全智能体的核心原理与工程落地逻辑。
SynTunSys-Design Space Exploration论文阅读
现代的VLSI设计,论文提出一个新的系统在工业VLSI设计流程中的逻辑和物理综合步骤中,自动进行DSE过程。 Pareto frontier帕累托边境,ABC三点的 A关闭时序(close timing)以9%的功率减少。C点在功率减少29%的情况下提高55%的时间 这是一个简单的two metrics的设计空间 SynTunSys SynTunSys天生可以容忍单个综合工作的失败,几乎没有降低结果整体质量的风险。 DevOps部署模型 新的实验方案可以是由EDA团队提供给设计者,..
gem5-gpu教程 DSENT (Design Space Exploration of Networks Tool) 配合gem5
DSENT是一种建模工具,旨在快速探索电子和新兴的片上光电网络(NoC)的设计空间。它为各种网络组件提供分析和参数化模型,并可在一系列技术假设下移植。给定架构级参数,DSENT从电气和光学构建块分层构建指定的模型,并输出详细的功率和面积估计。
LEGO-GraphRAG框架-图谱检索增强生成框架介绍
GraphRAG 通过利用具有嵌入式知识的图来增强大型语言模型的推理能力 (LLMs),解决了检索增强生成 (RAG) 中的重大挑战。尽管潜力巨大,但 GraphRAG 社区目前缺乏一个统一的框架来对基于图的知识检索过程进行细粒度分解。此外,检索过程中没有对现有解决方案进行系统分类或评估。在论文中,团队提出了 LEGO-GraphRAG,这是一个模块化框架,它将 GraphRAG 的检索过程分解为三个互连的模块:子图提取、路径过滤和路径细化。
【论文笔记】Deep Learning for Entity Matching: A Design Space Exploration
本文是介绍基于深度学习的实体对齐的一篇综述实体对齐(entity alignment)也被称为实体匹配(entity matching)特定属性的值(例如,品牌)在该属性的单元格中缺失,但出现在另一个属性的单元格中(例如,名称)这通常是由于不准确的属性提取(例如,提取“leather red”作为属性颜色的值,即使“leather”是属性材料的值)传统的实体对齐解决方案在这种情况下效果不佳。
FPGA—ZYNQ_BD Block Design学习(一)
1.第一步:打开Vivado软件,创建或打开一个工程。2.第二步:在Block Design中添加arm核心,并将其配置为IP核。3.第三步:配置arm核心的外设信息,如DDR接口、时钟频率、UART接口等。4.第四步:完成Block Design中的模块互联,生成PL端的比特流。 5.第五步:导出PS端的硬件信息,包括arm IP核的外设、速度、引脚和地址等信息。1创建bd 需要有ddr以及uart和时钟配置外设io口,这里就是zynq的管脚规定好的,根据原理图用哪个个勾选哪一个。 对外设uart的配
20160820:第二周论文学习+DSE:Design Space Exploration
20160820:第二周论文学习 黄鑫今天讲的最好,比较贴近论文内容,介绍的也比较详实。 老孟的准备比较差,对论文内容的理解都比较粗浅。
【项目管理】第8章 项目整合管理 --知识点整理
制定项目章程: 第一步,旨在明确项目的目标、范围、关键里程碑等关键信息,为项目的后续工作奠定基础。制订项目管理计划: 在项目章程的基础上,进一步详细规划项目的执行过程,包括时间、成本、质量、风险等方面的管理计划。指导与管理项目执行: 按照项目管理计划执行项目,同时监控项目的进展,确保项目按照计划进行。监控项目工作: 对项目的执行情况进行持续监控,及时发现并解决问题,确保项目目标的实现。
Type-C转DP1.4转C双向互传转接线方案
Type-C转DP双向互转方案的核心在于利用Type-C接口中的Alt Mode(交替模式)功能。通过利用Type-C接口的Alt Mode功能,该方案实现了Type-C接口与DP接口之间的双向互传,极大地丰富了用户的视觉体验。在选择Type-C转DP双向互转方案时,用户需要关注兼容性、性能需求、线缆长度和品牌等因素,以确保获得最佳的传输质量和使用体验。因此,Type-C转DP双向互转方案应运而生,旨在实现Type-C接口与DP接口之间的无缝连接,满足用户对高效能和高清晰度视频传输的需求。
【读论笔记】Toward Efficient Design Space Exploration for Fault-Tolerant Multiprocessor Systems_first part
随着晶体管尺寸的缩小、操作频率的增加和低电压应用,电路的瞬间故障率急剧上升。同时,为了满足日益增长的计算需求,越来越多的处理器被集成到单个芯片中。所以,对瞬间故障的容错率成为了设计纳米级多处理器系统的主要需求之一。
Voicebox本地部署:模型下载与离线模式实战指南
在本地语音处理场景中,模型下载失败和离线运行需求是开发者最常遇到的两大难题。理解语音工具的本地推理原理,关键在于掌握模型文件与程序逻辑的分离管理:模型独立下载,程序负责推理,输出留在本机。这种架构带来显著的技术价值——数据不出本地、不依赖公网、批量任务不中断。无论是语音识别转写、语音合成,还是集成到自动化脚本中,本地离线模式都能在隐私敏感或网络不稳定环境下稳定运行。对开发者而言,先解决模型文件的完整获取,再验证离线启动流程,就能绕过“无法下载模型”的常见坑。本文从环境准备、模型放置、服务启动到接口调用,提供
DeSpErate: Speeding-up Design Space Exploration by using Predictive Simulation Scheduling 论文笔记
abstract 设计空间探索(DSE)阶段是用来调整配置系统的参数。通常是一个多目标优化(MOO)问题。 It is usually done at pre-design phase and consists of the evaluation of large design spaces where each configuration requires long simulation.
【脚本篇】---spyglass lint脚本
【代码】【脚本篇】---spyglass lint脚本。
升级conda时出现Malformed version string invalid chars错误解决方案
但有时,当你使用“conda upgrade”的命令时,你可能会遇到一个错误,提示你的环境解析失败,出现“Malformed version string invalid chars”错误消息。如果以上两个步骤都没有解决你的问题,那么你可以考虑更新conda的依赖项。如果你的conda版本已经是最新的,那么你需要清理conda的缓存。最后,如果以上方法都无法解决问题,你可以尝试使用pip进行更新。如果你的conda版本过旧,你需要先更新conda。首先,你需要确认你当前使用的conda版本。
HLS DSE 综述笔记 | High-Level Synthesis Design Space Exploration: Past, Present, and Future
传送门 >>>>>>>>>>中文笔记。
Android16 rk3576添加触摸点数上限到40个点
本文介绍了在Android 16系统上实现40点触摸支持的修改方案。相比Android 15,Android 16对API添加有更严格的要求,需要在MotionEvent.java中添加@FlaggedApi批注。主要修改包括:1)在input_framework.aconfig中定义flag;2)在MotionEvent.java中添加40个AXIS_GENERIC轴常量并添加批注;3)将32位指针ID处理改为64位适配;4)更新相关API文档。修改涉及多个核心文件,包括PointerController
AI4EDA / AI4Design 完整研究报告:全球论文、项目、机构与产业路线
AI4EDA 与 AI4Design 的核心变化,不是“让大模型写 Verilog”这么简单,而是把芯片工程中的规格、代码、脚本、日志、波形、STA report、formal collateral、layout image、PPA 指标、制造计算等对象统一纳入可学习、可检索、可验证、可迭代的闭环。NVIDIA 的论文谱系清晰呈现了这条路径:先建立可执行评测,再做领域模型和数据工程,然后进入工具反馈、多智能体、长上下文、verifier-guided skill evolution。
基于深度学习的工业零件缺陷检测系统
工业零件缺陷检测系统摘要 本文介绍了一个基于深度学习的工业零件缺陷检测系统解决方案。该系统采用Faster R-CNN目标检测算法,结合PyTorch框架和OpenCV图像处理库,实现了对工业零件表面缺陷(如裂纹、划痕、凹坑等)的自动检测与定位。系统包含完整的开发流程:从数据采集与标注、数据增强预处理、模型构建与训练,到最终的评估与部署。相比传统机器视觉方法,该深度学习方案具有更强的特征表示能力和环境适应性,能够有效提升工业质检的准确率和效率。文章详细阐述了系统架构设计、实现细节和优化策略,并提供了完整的代
锂电池充电器电路设计 里面有电路
锂电池充电器电路设计 里面有电路 3.7V升压到5V电路设计。
Factorio与戴森球计划通用!FactorioLab支持多游戏的秘密解析
你是否曾经在玩Factorio(异星工厂)或戴森球计划(Dyson Sphere Program)时,为复杂的生产线规划而头疼?🤔 想要计算资源需求、优化工厂布局,却不知从何下手?今天,我要为你揭秘一个终极工厂游戏计算工具——FactorioLab!这个强大的计算器不仅支持Factorio,还兼容戴森球计划、Satisfactory、Captain of Industry等十多款工厂建造游戏!?
VB摄像头监控
该VB模块可对摄像头捕获的画面进行录像等,可在创建的窗口进行控制
SqueezeNet模型解读
SqueezeNet: AlexNet-Level accuracy with 50X fewer parameters And <0.5M Model Size 论文链接:http://arxiv.org/abs/1602.07360 代码链接:https://github.com/DeepScale/SqueezeNet Abstract 目前深度卷积神经网络主要聚焦于提升准确率,我们将...
数学建模模型总结
这是本人在两年内准备参加数学建模竞赛搜集到的模型资料,已经经过了本人的筛选和整理,希望能够对准备参加数学建模竞赛的学弟学妹们提供一些帮助!
jdk-8u144-linux-x64.tar.gz.
该资源为搭建Linux系统Java环境用,资源的后缀为tar.gz格式的压缩包
SqueezeNet详细解读
提出了新的网络架构Fire Module,通过减少参数来进行模型压缩 使用其他方法对提出的SqeezeNet模型进行进一步压缩 对参数空间进行了探索,主要研究了压缩比和3∗33∗3卷积比例的影响 这篇文章是 SQUEEZENET: ALEXNET-LEVEL ACCURACY WITH 50X FEWER PARAMETERS AND <0.5MB MODEL SIZE 的解读,在精简部...
设计空间探索DSE
设计空间探索(DSE)是一种系统化的方法,
组合microkernel进行卷积算子优化
背景介绍在广泛的科学和机器学习应用中,如何实现不同的优化张量计算的方法,在利用特定处理器结构的整体性能上是十分有必要的。同时,在接近处理器的最高性能时,微架构的复杂性使其变得非常困难。因此...
370



被折叠的 条评论
为什么被折叠?



