Jetson TX1使用usb camera采集图像 (1)

最新推荐文章于 2025-02-25 19:36:01 发布

weixin_33766805

最新推荐文章于 2025-02-25 19:36:01 发布

阅读量532

点赞数

CC 4.0 BY-SA版权

文章标签： python

原文链接：http://www.cnblogs.com/haiyang21/p/10704308.html

本文介绍如何使用Python和OpenCV在Jetson TX2上捕获并显示来自IP摄像机、USB网络摄像头及板载摄像头的视频。文章详细说明了安装OpenCV和GStreamer的步骤，并提供了一个示例代码tegra-cam.py，用于调整分辨率和选择不同类型的摄像头。

摘要生成于 C知道，由 DeepSeek-R1 满血版支持，前往体验 >

使用python实现

https://jkjung-avt.github.io/tx2-camera-with-python/

How to Capture and Display Camera Video with Python on Jetson TX2

Oct 19, 2017

Quick link: tegra-cam.py

In this post I share how to use python code (with OpenCV) to capture and display camera video on Jetson TX2, including IP CAM, USB webcam and the Jetson onboard camera. This sample code should work on Jetson TX1 as well.

Prerequisite:

OpenCV with GStreamer and python support needs to be built and installed on the Jetson TX2. I use opencv-3.4.0 and python3. You can refer to my earlier post for how to build and install OpenCV with python support: How to Install OpenCV (3.4.0) on Jetson TX2.
If you’d like to test with an IP CAM, you need to have it set up and know its RTSP URI, e.g. rtsp://admin:XXXXX@192.168.1.64:554.
Hook up a USB webcam (I was using Logitech C920) if you’d like to test with it. The USB webcam would usually be instantiated as /dev/video1, since the Jetson onboard camera has occupied /dev/video0.
Install gstreamer1.0-plugins-bad-xxx which include the h264parseelement. This is required for decoding H.264 RTSP stream from IP CAM.

$ sudo apt-get install gstreamer1.0-plugins-bad-faad \
                       gstreamer1.0-plugins-bad-videoparsers

Reference:

I developed my code based on this canny edge detector sample code.
ACCELERATED GSTREAMER FOR TEGRA X2 USER GUIDE: Descriptions of nvcamerasrc, nvvidconv and omxh264dec could be found in this document.

How to run the Tegra camera sample code:

Download the tegra-cam.py source code from my GitHubGist: https://gist.github.com/jkjung-avt/86b60a7723b97da19f7bfa3cb7d2690e
To capture and display video using the Jetson onboard camera, try the following. By default the camera resolution is set to 1920x1080 @ 30fps.

$ python3 tegra-cam.py

To use a USB webcam and set video resolution to 1280x720, try the following. The ‘–vid 1’ means using /dev/video1.

$ python3 tegra-cam.py --usb --vid 1 --width 1280 --height 720

To use an IP CAM, try the following command, while replacing the last argument with RTSP URI for you own IP CAM.

$ python3 tegra-cam.py --rtsp --uri rtsp://admin:XXXXXX@192.168.1.64:554

Discussions:

The crux of this tegra-cam.py script lies in the GStreamer pipelines I use to call cv.VideoCapture(). In my experience, using nvvidconv to do image scaling and to convert color format to BGRx (note that OpenCV requires BGR as the final output) produces better results in terms of frame rate.

def open_cam_rtsp(uri, width, height, latency):
    gst_str = ("rtspsrc location={} latency={} ! rtph264depay ! h264parse ! omxh264dec ! "
               "nvvidconv ! video/x-raw, width=(int){}, height=(int){}, format=(string)BGRx ! "
               "videoconvert ! appsink").format(uri, latency, width, height)
    return cv2.VideoCapture(gst_str, cv2.CAP_GSTREAMER)

def open_cam_usb(dev, width, height):
    # We want to set width and height here, otherwise we could just do:
    #     return cv2.VideoCapture(dev)
    gst_str = ("v4l2src device=/dev/video{} ! "
               "video/x-raw, width=(int){}, height=(int){}, format=(string)RGB ! "
               "videoconvert ! appsink").format(dev, width, height)
    return cv2.VideoCapture(gst_str, cv2.CAP_GSTREAMER) #该命令在测试时无法启动摄像头,但采用"return cv2.VideoCapture(0)"可以正常显示，I don`t know ???

def open_cam_onboard(width, height): # On versions of L4T previous to L4T 28.1, flip-method=2 # Use Jetson onboard camera gst_str = ("nvcamerasrc ! " "video/x-raw(memory:NVMM), width=(int)2592, height=(int)1458, format=(string)I420, framerate=(fraction)30/1 ! " "nvvidconv ! video/x-raw, width=(int){}, height=(int){}, format=(string)BGRx ! " "videoconvert ! appsink").format(width, height) return cv2.VideoCapture(gst_str, cv2.CAP_GSTREAMER)

Here’s a screenshot of my Jetson TX2 running tegra-cam.py with a live IP CAM video feed. (I also hooked up a Faster R-CNN model to do human head detection and draw bounding boxes on the captured images here, but the main video capture/display code was the same.)

Screenshot of tegra-cam.py on Jetson TX2

If you like this post or have any questions, feel free to leave a comment below. Otherwise be sure to also check out my next post How to Capture Camera Video and Do Caffe Inferencing with Python on Jetson TX2, in which I demonstrate how to feed live camera images into a Caffe pipeline for real-time inferencing.

转载于:https://www.cnblogs.com/haiyang21/p/10704308.html