HCL配置工作

Smart-link 准备工作

SW1:

Vlan 10

Vlan 20

Vlan 30

Vlan 40

Vlan 100

Vlan 200

Int ran g1/0/1to g1/0/2

port link-type trunk

Port trunk per vlan 10 20 30 40 100 200

Dis cu  复制 #vlan 10到g1/0/2的结尾包括# 粘贴到SW2、SW3、SW4

回到SW1

undo stp enable

qu

stp re

Ins 1 vlan 10 20

Ins 2 vlan 30 40

act re

qu

[SW1]smart-link group 1

[SW1-smlk-group1]protected-vlan reference-instance 1

[SW1-smlk-group1]flush enable control-vlan 100

[SW1-smlk-group1]port g1/0/1 primary

[SW1-smlk-group1]port g1/0/2 secondary

[SW1]smart-link group 2

[SW1-smlk-group2]protected-vlan reference-instance 2

[SW1-smlk-group2]flush enable control-vlan 200

[SW1-smlk-group2]port g1/0/2 primary

[SW1-smlk-group2]port g1/0/1 secondary

[SW2-GigabitEthernet1/0/1]smart-link flush enable control-vlan 100 200

[SW2-GigabitEthernet1/0/2]smart-link flush enable control-vlan 100 200

在SW2，SW3,SW4分别配置

[SW1-smlk-group1]protected-vlan reference-instance 0

[SW1-smlk-group1]preemption mode role

[SW1-smlk-group2]preemption mode role

[SW2]monitor-link group 1

[SW2-mtlk-group1]port g1/0/2 uplink

[SW2-mtlk-group1]port g1/0/1 downlink

在SW3上写相同命令

Pppoe实验

PC配置：192.168.1.1

                255.255.255.0

                192.168.1.254

R1

Int g0/0

Ip add 192.168.1.254 24

[R2]local-user wangdaye class network

New local user added.

[R2-luser-network-wangdaye]password simple 123456

[R2-luser-network-wangdaye]service-type ppp

[R2]ip pool 1 200.1.1.1 200.1.1.10

[R2]domain h3c

[R2-isp-h3c]authentication ppp local

[R2]interface Virtual-Template 1

[R2-Virtual-Template1]ppp authentication-mode chap domain h3c

[R2-Virtual-Template1]remote address pool 1

[R2-Virtual-Template1]ip address 200.1.1.254 24

[R2-GigabitEthernet0/0]pppoe-server bind virtual-template 1

[R1]dialer-group 1 rule ip permit 

[R1]interface Dialer 1

[R1-Dialer1]ip address ppp-negotiate 

[R1-Dialer1]dialer bundle enable 

[R1-Dialer1]dialer-group 1

[R1-Dialer1]ppp chap user wangdaye

[R1-Dialer1]ppp chap password simple 123456

[R1-GigabitEthernet0/1]pppoe-client dial-bundle-number 1

[R1-Dialer1]dialer timer idle 0

[R1]ip route-static 0.0.0.0 0 dialer 1

R1

acl ad name easyIP

rule per ip so 192.168.1.0 0.0.0.255

qu

Int dia 1

Nat outbound name easyIP

最后R2

Int lo 0

Ip add 202.1.1.1 32

BGP实验

R1

Int l0

Ip add 192.168.1.1 24

Int g0/0

Ip add 100.1.1.1 24

R2

Int g0/0

Ip add 100.1.1.2 24

Int g0/1

Ip add 100.2.2.2 24

Int l0

Ip add 2.2.2.2 32

R3

Int l0

Ip add 3.3.3.3 32

Int g0/0

Ip add 100.2.2.3 24

Int g0/1

Ip add 100.3.3.3 24

R4

Int l0

Ip add 4.4.4.4 32

Int g0/0

Ip add 100.3.3.4 24

Int g0/1

Ip add 100.4.4.4 24

R5

Int l0

Ip add 192.168.2.1 24

Int g0/0

Ip add 100.4.4.5 24

R2

ospf 0

area 0

net 100.2.2.0 0.0.0.255

Net 2.2.2.2 0.0.0.0

R3

Ospf

Area 0

Net 100.2.2.0 0.0.0.255

Net 100.3.3.0 0.0.0.255

Net 3.3.3.3 0.0.0.0

R4

Ospf

Area 0

Net 100.3.3.3.0 0.0.0.255

Net 4.4.4.4 0.0.0.0

[R1]bgp 100

[R1-bgp-default]peer 100.1.1.2 as-number 200

[R1-bgp-default]address-family ipv4 unicast

[R1-bgp-default-ipv4]peer 100.1.1.2 enable

[R2]bgp 200

[R2-bgp-default]peer 100.1.1.1 as-number 100

[R2-bgp-default]peer 4.4.4.4 as-number 200

[R2-bgp-default]peer 4.4.4.4 connect-interface LoopBack 0

[R2-bgp-default]address-family ipv4 unicast

[R2-bgp-default-ipv4]peer 100.1.1.1 enable

[R2-bgp-default-ipv4]peer 4.4.4.4 enable

[R2-bgp-default-ipv4]peer 4.4.4.4 next-hop-local

[R4]bgp 200

[R4-bgp-default]peer 100.4.4.5 as-number 300

[R4-bgp-default]peer 2.2.2.2 as-number 200

[R4-bgp-default]peer 2.2.2.2 connect-interface LoopBack 0

[R4-bgp-default]address-family ipv4 unicast

[R4-bgp-default-ipv4]peer 100.4.4.5 enable

[R4-bgp-default-ipv4]peer 2.2.2.2 enable

[R4-bgp-default-ipv4]peer 2.2.2.2 next-hop-local

[R5]bgp 300

[R5-bgp-default]peer 100.4.4.4 as-number 200

[R5-bgp-default]address-family ipv4 unicast

[R5-bgp-default-ipv4]peer 100.4.4.4 enable

[R1-bgp-default-ipv4]network 192.168.1.0 24

[R5-bgp-default-ipv4]network 192.168.2.0 24

[R2-ospf-1]import-route bgp

[R4-ospf-1]import-route bgp