[Review]Static PE-CE Routing

本文展示了在ATM链路上配置OSPF的具体步骤及注意事项,包括在PVC上设置广播模式,并提供了R1至R6路由器的详细配置脚本。

摘要生成于 C知道 ,由 DeepSeek-R1 满血版支持, 前往体验 >

今天好多ISO的配置还是有些生疏 尤其是OSPF在ATM这些链路上的配置

OSPF over ATM 链路的情景

一定要考虑到 PVC 上配置broadcast

在接口下使能 ip ospf network broadcast

 

 

在此贴上配置:

#####R1##########

Router#show running-config
Building configuration...
Current configuration : 864 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!no ip dhcp use vrf connected
!
!
no ip ips deny-action ips-interface
!!
interface Loopback0
 ip address 1.1.1.1 255.255.255.255
!

interface FastEthernet0/0
 no ip address
 shutdown
 duplex half
!
interface FastEthernet1/0
 ip address 172.16.10.2 255.255.255.252
 duplex auto
 speed auto

!
interface FastEthernet1/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.10.1
no ip http server
no ip http secure-server
!!
control-plane
!

!
gatekeeper
 shutdown
!
!
line con 0
 stopbits 1
line aux 0
line vty 0 4
!
!
end

#######R2###########

Building configuration...

Current configuration : 1710 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip vrf vpn1
 rd 1:100
 route-target export 1:100
 route-target import 1:100
!

no ip ips deny-action ips-interface
!
mpls label protocol ldp
mpls ldp router-id Loopback0
!
!
interface Loopback0
 ip address 10.10.10.101 255.255.255.255

!

interface FastEthernet0/0
 no ip address
 shutdown
 duplex half
!
interface FastEthernet1/0
 ip vrf forwarding vpn1
 ip address 172.16.10.1 255.255.255.252
 duplex auto
 speed auto
!
interface FastEthernet1/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface ATM2/0
 ip address 10.10.10.1 255.255.255.252
 ip ospf network broadcast
 no atm ilmi-keepalive
 mpls ip
 pvc 2/200
  broadcast
  encapsulation aal5snap

 !
!
router ospf 1
 log-adjacency-changes
 network 0.0.0.0 255.255.255.255 area 0
!
router bgp 1
 no synchronization
 bgp log-neighbor-changes
 neighbor 10.10.10.102 remote-as 1
 neighbor 10.10.10.102 update-source Loopback0
 no auto-summary
 !
 address-family vpnv4
 neighbor 10.10.10.102 activate
 neighbor 10.10.10.102 send-community extended
 exit-address-family
 !
 address-family ipv4 vrf vpn1
 redistribute connected
 redistribute static
 no auto-summary
 no synchronization
 exit-address-family

!
ip classless
ip route vrf vpn1 1.1.1.1 255.255.255.255 172.16.10.2
no ip http server
no ip http secure-server
!
control-plane
!
gatekeeper
 shutdown
!
line con 0
 stopbits 1
line aux 0
line vty 0 4
!
!
end

 

#####R3###################

Router#show running-config
Building configuration...

Current configuration : 1131 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
no ip ips deny-action ips-interface
!
mpls label protocol ldp
mpls ldp router-id Loopback0
!

interface Loopback0
 ip address 10.10.10.200 255.255.255.255

!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex half
!
interface ATM1/0
 ip address 10.10.10.2 255.255.255.252
 ip ospf network broadcast
 no atm ilmi-keepalive
 mpls ip
 pvc 2/200
  broadcast
  encapsulation aal5snap

 !
!
interface ATM2/0
 ip address 10.10.10.5 255.255.255.252
 ip ospf network broadcast
 no atm ilmi-keepalive
 mpls ip
 pvc 2/300
  broadcast
  encapsulation aal5snap

 !
!
router ospf 1
 log-adjacency-changes
 network 0.0.0.0 255.255.255.255 area 0

!
ip classless
no ip http server
no ip http secure-server!
!
control-plane!
!
gatekeeper
 shutdown!
!
line con 0
 stopbits 1
line aux 0
line vty 0 4!
!
end

#####R4#####

Router#show running-config
Building configuration...

Current configuration : 1106 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
no ip dhcp use vrf connected
!
no ip ips deny-action ips-interface
!
mpls label protocol ldp
mpls ldp router-id Loopback0
!
interface Loopback0
 ip address 10.10.10.201 255.255.255.255

!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex half
!
interface ATM1/0
 ip address 10.10.10.6 255.255.255.252
 ip ospf network broadcast
 no atm ilmi-keepalive
 mpls ip
 pvc 2/300
  broadcast

 !
!
interface ATM2/0
 ip address 10.10.10.9 255.255.255.252
 ip ospf network broadcast
 no atm ilmi-keepalive
 mpls ip
 pvc 2/400
  broadcast
  encapsulation aal5snap

 !
!
router ospf 1
 log-adjacency-changes
 network 0.0.0.0 255.255.255.255 area 0

!
ip classless
no ip http server
no ip http secure-server
!
control-plane
!
!
gatekeeper
 shutdown
!
!
line con 0
 stopbits 1
line aux 0
line vty 0 4
!
!
end

Router#

 

 

#####R5######

Router#show run
Building configuration...

Current configuration : 1711 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
ip vrf vpn1
 rd 1:100
 route-target export 1:100
 route-target import 1:100

!
no ip ips deny-action ips-interface
!
mpls label protocol ldp
mpls ldp router-id Loopback0
!
interface Loopback0
 ip address 10.10.10.102 255.255.255.255

!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex half
!
interface FastEthernet1/0
 ip vrf forwarding vpn1
 ip address 172.16.20.1 255.255.255.252
 duplex auto
 speed auto

!
interface FastEthernet1/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
interface ATM2/0
 ip address 10.10.10.10 255.255.255.252
 ip ospf network broadcast
 no atm ilmi-keepalive
 mpls ip
 pvc 2/400
  broadcast
  encapsulation aal5snap

 !
!
router ospf 1
 log-adjacency-changes
 network 0.0.0.0 255.255.255.255 area 0

!
router bgp 1
 no synchronization
 bgp log-neighbor-changes
 neighbor 10.10.10.101 remote-as 1
 neighbor 10.10.10.101 update-source Loopback0
 no auto-summary
 !
 address-family vpnv4
 neighbor 10.10.10.101 activate
 neighbor 10.10.10.101 send-community extended
 exit-address-family
 !
 address-family ipv4 vrf vpn1
 redistribute connected
 redistribute static
 no auto-summary
 no synchronization
 exit-address-family
!

ip classless
ip route vrf vpn1 6.6.6.6 255.255.255.255 172.16.20.2
no ip http server
no ip http secure-server
!
control-plane
!
gatekeeper
 shutdown
!
!
line con 0
 stopbits 1
line aux 0
line vty 0 4
!
!
end

Router#

 

 

 

##########R6#########

Router#show run
Router#show running-config
Building configuration...

Current configuration : 864 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
no ip ips deny-action ips-interface

!
interface Loopback0
 ip address 6.6.6.6 255.255.255.255

!
interface FastEthernet0/0
 no ip address
 shutdown
 duplex half
!
interface FastEthernet1/0
 ip address 172.16.20.2 255.255.255.252
 duplex auto
 speed auto

!
interface FastEthernet1/1
 no ip address
 shutdown
 duplex auto
 speed auto
!
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.20.1
no ip http server
no ip http secure-server
!
control-plane
!
gatekeeper
 shutdown
!
!
line con 0
 stopbits 1
line aux 0
line vty 0 4
!
!
end

 

 

<think>好的,我需要解释Cilium中的Native-Routing和Host-Routing的区别。首先,我应该回忆一下Cilium的基本网络机制,它通常基于eBPF来实现网络策略和负载均衡。用户可能是在部署或优化Kubernetes网络时遇到选择路由模式的问题,所以需要了解这两种模式的适用场景和工作原理。 首先,Native-Routing,这个词听起来像是直接利用宿主机的现有路由设施,比如Linux内核的路由表,而不是通过覆盖网络(如VXLAN)。这可能意味着数据包在节点之间直接路由,不需要封装,适合在底层网络支持Pod IP直接可达的环境中,比如云提供商的VPC或本地数据中心的BGP网络。这种情况下,Cilium可能不创建额外的隧道,而是依赖底层网络的路由能力。 然后是Host-Routing,这可能指的是每个节点上的路由表处理Pod之间的流量。在传统的Kubernetes网络模型中,每个节点上的CNI插件负责设置路由规则,将Pod的流量导向正确的节点。Host-Routing可能指的是这种基于主机路由表的方式,可能使用主机的网络命名空间来处理流量转发,比如通过veth pair连接Pod和主机网络,然后依靠主机的路由规则进行转发。这种情况下,流量可能经过主机的网络栈,可能涉及iptables或eBPF的处理。 需要确认这两种模式的具体定义。查阅Cilium文档,Native-Routing通常指不使用覆盖网络,直接利用底层网络的路由能力,而Host-Routing可能更侧重于节点内部的路由处理,比如Pod到Pod在同一节点或跨节点的通信通过主机的路由表进行,可能结合eBPF优化。 可能存在的混淆点在于,Native-Routing可能属于Host-Routing的一种情况,或者两者是不同的层面。比如,Native-Routing涉及跨节点的路由方式,而Host-Routing涉及节点内部的路由机制。或者Host-Routing是Cilium在特定配置下的路由模式,比如当隧道模式关闭时,使用主机路由表进行跨节点通信。 另外,Cilium的隧道模式(如VXLAN)和路由模式(如Native-Routing)是两种不同的跨节点通信方式。当启用Native-Routing时,Cilium假设网络层能够正确处理Pod IP的路由,因此无需封装,直接发送原始IP包。而Host-Routing可能更强调使用主机的路由表,而不是覆盖网络,这可能包括Native-Routing的情况,但Host-Routing也可能指节点内部的路由处理,比如通过主机的网络接口转发Pod流量。 需要进一步区分两者的具体应用场景。例如,Native-Routing适合网络基础设施支持Pod IP路由的环境,而Host-Routing可能更通用,可以结合不同的底层路由机制,包括Native-Routing或其他方式。 可能还需要考虑性能差异。Native-Routing由于无需封装和解封装,可能具有更低的延迟和更高的吞吐量,但要求底层网络支持。而Host-Routing如果指的是基于主机路由表的处理,可能在某些场景下效率稍低,但兼容性更好。 总结来说,用户需要明确Native-Routing和Host-Routing在Cilium中的具体定义、工作机制、适用场景以及配置方式。需要确保回答中准确区分两者,避免混淆,并提供实际用例或配置示例帮助理解。</think>### Cilium 的 Native-Routing 与 Host-Routing 模式详解 Cilium 的 **Native-Routing** 和 **Host-Routing** 是两种不同的网络流量转发机制,均用于优化 Kubernetes 集群内外的通信效率。以下是两者的核心区别与应用场景分析: --- ### 一、**Native-Routing(原生路由)** #### 1. **核心原理** - **直接利用底层网络路由**: Native-Routing 模式下,Cilium **不依赖覆盖网络(如 VXLAN、IPIP)**,而是直接使用底层网络(如云厂商 VPC、物理机 BGP 路由)的现有路由能力转发数据包。 - **无封装开销**: Pod 发出的数据包以**原始 IP 格式**传输,无需添加隧道头部,减少带宽消耗和延迟。 #### 2. **适用条件** - **底层网络需支持 Pod IP 路由**: 集群所有节点的底层网络(如 AWS VPC、GCP VPC)必须能识别并正确转发 Pod IP 的流量。 - **Pod IP 可达性**: Pod IP 必须在集群外部网络中可路由(例如通过 BGP 宣告或静态路由配置)。 #### 3. **典型场景** - **云环境 VPC 网络**: 云厂商的 VPC 支持直接路由 Pod IP,无需额外隧道。 - **混合云/本地数据中心**: 通过 BGP 协议将 Pod IP 路由通告到物理网络。 #### 4. **配置示例** ```yaml # 启用 Native-Routing(禁用隧道) tunnel: disabled ipam: mode: kubernetes enableIPv4Masquerade: false # 假设底层网络已支持 Pod IP 路由 ``` --- ### 二、**Host-Routing(主机路由)** #### 1. **核心原理** - **依赖节点路由表**: Host-Routing 模式下,Cilium 通过配置**节点的 Linux 内核路由表**,实现跨节点 Pod 流量的转发。 - **可能结合隧道或直接路由**: Host-Routing 既可以与 Native-Routing 配合使用(无隧道),也可与覆盖网络(如 VXLAN)结合。 #### 2. **工作模式** - **同节点 Pod 通信**: 通过 `veth pair` 直接连接 Pod 与主机网络命名空间,流量经主机网络栈转发。 - **跨节点 Pod 通信**: - **无隧道(Native-Routing)**:依赖底层网络路由 Pod IP。 - **有隧道(如 VXLAN)**:封装流量后通过隧道传输。 #### 3. **典型场景** - **通用 Kubernetes 网络**: 作为 Cilium 的默认路由基础,兼容各类网络拓扑。 - **边缘计算/资源受限环境**: 通过优化主机路由表减少性能开销。 #### 4. **配置示例** ```yaml # 启用 Host-Routing(默认行为,通常无需显式配置) enableHostReachableServices: true # 优化主机服务可达性 ``` --- ### 三、**Native-Routing 与 Host-Routing 的对比** | **特性** | **Native-Routing** | **Host-Routing** | |------------------------|----------------------------------------|---------------------------------------| | **依赖隧道** | 否 | 可选(可结合 VXLAN 或直接路由) | | **封装开销** | 无 | 若有隧道则存在封装开销 | | **底层网络要求** | 必须支持 Pod IP 路由 | 无特殊要求(依赖主机路由表配置) | | **性能** | 更高(无封装、路径更短) | 取决于是否启用隧道 | | **适用场景** | 云 VPC、BGP 网络 | 通用场景,兼容复杂网络拓扑 | | **配置复杂度** | 高(需确保路由可达性) | 低(Cilium 自动管理路由表) | --- ### 四、**组合使用场景** #### 1. **Native-Routing + Host-Routing** - **原理**: 利用底层网络路由跨节点流量(Native-Routing),同时依赖节点路由表处理本地转发(Host-Routing)。 - **优势**: 兼具高性能和灵活性,适合云环境与混合云部署。 - **配置**: ```yaml tunnel: disabled enableHostReachableServices: true ``` #### 2. **Host-Routing + VXLAN 隧道** - **原理**: 通过 Host-Routing 管理节点内流量,跨节点流量使用 VXLAN 封装。 - **适用场景**: 底层网络不支持 Pod IP 路由(如传统 IDC 网络)。 - **配置**: ```yaml tunnel: vxlan ``` --- ### 五、**验证与调试** #### 1. **检查 Native-Routing 状态** ```bash # 查看路由表是否包含 Pod CIDR 路由 $ ip route show | grep <pod-cidr> # 确认隧道接口不存在(如 cilium_vxlan) $ ip link show | grep cilium_ ``` #### 2. **分析 Host-Routing 路径** ```bash # 跟踪跨节点 Pod 流量路径 $ kubectl exec -it <pod-name> -- traceroute <target-pod-ip> # 检查主机路由表 $ ip route list table all ``` --- ### 六、**性能优化建议** 1. **Native-Routing 场景**: - 启用 **eBPF Host-Routing(Kernel ≥ 5.10)** 绕过 iptables: ```yaml enableBPFHostRouting: true ``` - 使用 **XDP 加速**(需网卡支持): ```yaml bpf: lbBypassFIBLookup: true ``` 2. **Host-Routing 场景**: - 禁用 `kube-proxy`,使用 **Cilium eBPF 替代**: ```yaml kubeProxyReplacement: strict ``` - 优化主机路由缓存: ```bash sysctl -w net.ipv4.route.gc_timeout=300 ``` --- ### 总结 - **Native-Routing**: 适用于底层网络支持 Pod IP 路由的高性能场景,**避免隧道开销**,但对网络基础设施要求较高。 - **Host-Routing**: Cilium 的默认路由基础机制,**灵活兼容各类网络**,可结合隧道或直接路由,适合通用 Kubernetes 集群。 实际部署时,若云环境或数据中心支持 Pod IP 直接路由(如 AWS VPC 路由表自动同步 Pod CIDR),优先选择 **Native-Routing + Host-Routing** 组合以最大化性能;若网络条件受限,则通过 **Host-Routing + 隧道** 实现跨节点通信。
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值