树莓派4B接电视HDMI分辨率不正确、无声音的处理办法

最新推荐文章于 2025-05-14 11:27:12 发布

Glory1950

最新推荐文章于 2025-05-14 11:27:12 发布

阅读量9.4k

点赞数 2

CC 4.0 BY-SA版权

文章标签：树莓派 HDMI 无声音分辨率

本文链接：https://blog.youkuaiyun.com/Eginx/article/details/104142635

树莓派4B通过HDMI连接电视时遇到分辨率错误和无声音的问题。经排查，问题电视在使用其他设备时正常。通过修改/boot/config.txt配置文件调整显示模式，然后重启，成功解决了分辨率和声音异常的问题。

摘要生成于 C知道，由 DeepSeek-R1 满血版支持，前往体验 >

树莓派4B通过HDMI接口连接电视时，分辨率不正确、没有声音，使用同品牌不同电视测试正常。

接回有问题的电视

pi@raspberrypi:~ $ tvservice -m DMT
Group DMT has 4 modes:
           mode 4: 640x480 @ 60Hz 4:3, clock:25MHz progressive 
           mode 9: 800x600 @ 60Hz 4:3, clock:40MHz progressive 
           mode 16: 1024x768 @ 60Hz 4:3, clock:65MHz progressive 
           mode 39: 1360x768 @ 60Hz 16:9, clock:85MHz progressive 
pi@raspberrypi:~ $ tvservice -m CEA
Group CEA has 16 modes:
           mode 1: 640x480 @ 60Hz 4:3, clock:25MHz progressive 
           mode 2: 720x480 @ 60Hz 4:3, clock:27MHz progressive 
           mode 3: 720x480 @ 60Hz 16:9, clock:27MHz progressive 
  (prefer) mode 4: 1280x720 @ 60Hz 16:9, clock:74MHz progressive 
           mode 5: 1920x1080 @ 60Hz 16:9, clock:74MHz interlaced 
           mode 6: 720x480 @ 60Hz 4:3, clock:27MHz x2 interlaced 
           mode 7: 720x480 @ 60Hz 16:9, clock:27MHz x2 interlaced 
           mode 16: 1920x1080 @ 60Hz 16:9, clock:148MHz progressive 
           mode 17: 720x576 @ 50Hz 4:3, clock:27MHz progressive 
           mode 18: 720x576 @ 50Hz 16:9, clock:27MHz progressive 
           mode 19: 1280x720 @ 50Hz 16:9, clock:74MHz progressive 
           mode 20: 1920x1080 @ 50Hz 16:9, clock:74MHz interlaced 
           mode 22: 720x576 @ 50Hz 16:9, clock:27MHz x2 interlaced 
           mode 31: 1920x1080 @ 50Hz 16:9, clock:148MHz progressive 
           mode 32: 1920x1080 @ 24Hz 16:9, clock:74MHz progressive 
           mode 34: 1920x1080 @ 30Hz 16:9, clock:74MHz progressive

修改/boot/config.txt调整显示模式：

pi@raspberrypi:~ $ sudo vi /boot/config.txt
# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2 //取消注释

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
hdmi_drive=2 //取消注释

重启后分辨率及声音恢复正常。