dell交换机固件

Upgrading the S4048-ON Dell Networking OS Image using the Dell Networking OS CLI
Bare Metal Provisioning 

NOTE: If you are using Bare Metal Provisioning (BMP), see the Bare Metal Provisioning topic in the Dell Networking OS Configuration Guide or the Open Automation Guide. 

Manual Upgrade Procedure 

Follow these steps carefully to upgrade your S4048-ON systems: 

1 Dell Networking recommends that you back up your startup configuration and any important files and directories to an external media prior to upgrading the system. 

2 Upgrade the Dell Networking OS in flash partition A: or B: 

upgrade system [flash: | ftp: stack-unit <1-6> | tftp: | scp: | usbflash:] [A: | B:] EXEC Privilege
Dell#upgrade system ftp: a: 

Address or name of remote host []: 10.16.127.35 Source file name []: FTOS-SK-9.10.0.1.bin 

User name to login remote host: ftpuser Password to login remote host: 

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!... 

........................................................ 

........................................................ 

........................................................ 

........................................................ 

........................................................ 

........................................................ 

........60413463 bytes successfully copied System image upgrade completed successfully. 

Dell#Apr 12 04:42:52: %STKUNIT1-M:CP %DOWNLOAD-6-UPGRADE: Upgrade completed successfully 

Dell# 

3 Verify that the Dell Networking OS has been upgraded correctly in the upgraded flash partition show boot system stack-unit [1-6] | all] 


EXEC Privilege 

Dell#show boot system stack-unit all 

Current system image information in the system: 

=============================================== 

Type Boot Type A B 

--------------------------------------------------------------------------------------------- 

- 

stack-unit 1 FLASH BOOT 9.10(0.1) 9.10(0.0) [boot] 

stack-unit 2 is not present. 

stack-unit 3 is not present. stack-unit 4 is not present. stack-unit 5 is not present. stack-unit 6 is not present. Dell# 

4 Change the Primary Boot Parameter of the S4048-ON to the upgraded partition A: or B: boot system stack-unit 1 primary system: [A: | B: | tftp: | ftp:] 


CONFIGURATION 

5 Save the configuration so that the configuration will be retained after a reload using write memory command. write [memory] 


EXEC PRIVILEGE 

Dell#write memory 

! 

Apr 12 04:44:35: %STKUNIT1-M:CP %FILEMGR-5-FILESAVED: Copied running-config to startup- config in flash by default 

Dell# 

6 Reload the unit reload 


EXEC PRIVILEGE 

Command : reload 

Mode : EXEC PRIVILEGE 

Dell#reload 

Proceed with reload [confirm yes/no]: y 

Apr 12 04:44:42: %STKUNIT1-M:CP %CHMGR-5-RELOAD: User request to reload the chassis syncing disks... 

done 

7 Verify the S4048 ON has been upgraded to the Dell Networking OS version 9.10(0.1) show version 


EXEC PRIVILEGE 

Dell#show version 

Dell Real Time Operating System Software Dell Operating System Version: 2.0 

Dell Application Software Version: 9.10(0.1) 

Copyright (c) 1999-2016 by Dell Inc. All Rights Reserved. Build Time: Sun Apr 10 06:42:55 2016 

Build Path: /sites/eqx/work/swbuild01_1/build16/E9-10-0/SW/SRC Dell Networking OS uptime is 2 hour(s), 24 minute(s) 

System image file is "system://A" System Type: S4048-ON 

Control Processor: Intel Rangeley with 2 Gbytes (2127560704 bytes) of memory, core(s) 2. 

8G bytes of boot flash memory. 

1 54-port TE/FG (SK-ON) 

48 Ten GigabitEthernet/IEEE 802.3 interface(s) 

6 Forty GigabitEthernet/IEEE 802.3 interface(s) Dell#

转载于:https://www.cnblogs.com/ligao/p/6090023.html