static void SetSysClockTo72(void)的一些理解

static void SetSysClockTo72(void)

{

  __IO uint32_t StartUpCounter = 0, HSEStatus = 0;

  

  /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/    

  /* Enable HSE */    

  RCC->CR |= ((uint32_t)RCC_CR_HSEON);//打开HSE

 

  /* Wait till HSE is ready and if Time out is reached exit */

  do

  {

    HSEStatus = RCC->CR & RCC_CR_HSERDY;

    StartUpCounter++;  

  } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT));//等待HSE就绪

 

  if ((RCC->CR & RCC_CR_HSERDY) != RESET)

  {

    HSEStatus = (uint32_t)0x01;

  }

  else

  {

    HSEStatus = (uint32_t)0x00;

  }  

 

  if (HSEStatus == (uint32_t)0x01)

  {

    /* Enable Prefetch Buffer */

    FLASH->ACR |= FLASH_ACR_PRFTBE;

 

    /* Flash 2 wait state */

    FLASH->ACR &= (uint32_t)((uint32_t)~FLASH_ACR_LATENCY);

    FLASH->ACR |= (uint32_t)FLASH_ACR_LATENCY_2;    //先不管

 

 

    /* HCLK = SYSCLK */

    RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1;

      

    /* PCLK2 = HCLK */

    RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1;

    

    /* PCLK1 = HCLK /2*/

    RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV2;//设置三个时钟的分频系数,确定其和系统时钟的关系

 

#ifdef STM32F10X_CL

    /* Configure PLLs ------------------------------------------------------*/

    /* PLL2 configuration: PLL2CLK = (HSE / 5) * 8 = 40 MHz */

    /* PREDIV1 configuration: PREDIV1CLK = PLL2 / 5 = 8 MHz */

        

    RCC->CFGR2 &= (uint32_t)~(RCC_CFGR2_PREDIV2 | RCC_CFGR2_PLL2MUL |

                              RCC_CFGR2_PREDIV1 | RCC_CFGR2_PREDIV1SRC);

    RCC->CFGR2 |= (uint32_t)(RCC_CFGR2_PREDIV2_DIV5 | RCC_CFGR2_PLL2MUL8 |

                             RCC_CFGR2_PREDIV1SRC_PLL2 | RCC_CFGR2_PREDIV1_DIV5);

  

    /* Enable PLL2 */

    RCC->CR |= RCC_CR_PLL2ON;

    /* Wait till PLL2 is ready */

    while((RCC->CR & RCC_CR_PLL2RDY) == 0)

    {

    }

    

   

    /* PLL configuration: PLLCLK = PREDIV1 * 9 = 72 MHz */

    RCC->CFGR &= (uint32_t)~(RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLSRC | RCC_CFGR_PLLMULL);

    RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLSRC_PREDIV1 |

                            RCC_CFGR_PLLMULL9); //确定PLL的倍频系数和时钟来源

#else    

    /*  PLL configuration: PLLCLK = HSE * 9 = 72 MHz */

    RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE |

                                        RCC_CFGR_PLLMULL));//将PLLSRC，PLLXTPRE，PLLMULL对应的位置零

    RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMULL9);// 或符号”|”是前后两种状态同时取的意思

#endif /* STM32F10X_CL */

 

    /* Enable PLL */

    RCC->CR |= RCC_CR_PLLON;//PLL时钟打开

 

    /* Wait till PLL is ready */

    while((RCC->CR & RCC_CR_PLLRDY) == 0)

    {

    }

    

    /* Select PLL as system clock source */

    RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW));

    RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL;//将PLL作为系统时钟来源    

 

    /* Wait till PLL is used as system clock source */

    while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)0x08)

    {

    }

  }

  else

  { /* If HSE fails to start-up, the application will have wrong clock

         configuration. User can add here some code to deal with this error */

  }

}

#endif