(本人简单翻译了一下如有错误还请指出,谢谢各位网友)
----------------------
f Firmware info(显示固件信息)
h halt(暂停CPU)
g go(运行)
Sleep Waits the given time (in milliseconds). Syntax: Sleep <delay>(睡眠多少毫秒)
s Single step the target chip(单步调试目标芯片)
st Show hardware status(显示硬件状态)
hwinfo Show hardware info(显示硬件信息)
mem Read memory. Syntax: mem <Addr>, <NumBytes> (hex)(读内存)
mem8 Read 8-bit items. Syntax: mem8 <Addr>, <NumBytes> (hex)(读内存8字节)
mem16 Read 16-bit items. Syntax: mem16 <Addr>, <NumItems> (hex)mem32 Read 32-bit items. Syntax: mem32 <Addr>, <NumItems> (hex)
w1 Write 8-bit items. Syntax: w1 <Addr>, <Data> (hex)(写内存8字节)
w2 Write 16-bit items. Syntax: w2 <Addr>, <Data> (hex)(读内存16字节)
w4 Write 32-bit items. Syntax: w4 <Addr>, <Data> (hex)(读内存32字节)
wm Write test words. Syntax: wm <NumWords>
is Identify length of scan chain select register
ms Measure length of scan chain. Syntax: ms <Scan chain>
mr Measure RTCK react time. Syntax: mr
q Quit(推出)
qc Close JLink connection and quit(关闭jlink连接,并退出)
r Reset target (RESET)(重启目标)
rx Reset target (RESET). Syntax: rx <DelayAfterReset>(延时重启)
RSetType Set the current reset type. Syntax: RSetType <type>
Regs Display contents of registers(显示寄存器信息)
wreg Write register. Syntax: wreg <RegName>, <Value>(写继承器)
SetBP Set breakpoint. Syntax: SetBP <addr> [A/T] [S/H](设置断点)
SetWP Set Watchpoint. Syntax: <Addr> [R/W] [<Data> [<D-Mask>] [A-Mask]](设置监视点)
ClrBP Clear breakpoint. Syntax: ClrBP <BP_Handle>(清除断点)
ClrWP Clear watchpoint. Syntax: ClrWP <WP_Handle>(清楚监视点)
VCatch Write vector catch. Syntax: VCatch <Value>
loadbin Load binary file into target memory.(下载bin文件到目标内存)
Syntax: loadbin <filename>, <addr>
savebin Saves target memory into binary file.(保存BIN文件)
Syntax: savebin <filename>, <addr>, <NumBytes>
SetPC Set the PC to specified value. Syntax: SetPC <Addr>(设置PC(r15)寄存器)
le Change to little endian mode(设置成小端模式)
be Change to big endian mode(设置成大端模式)
log Enables log to file. Syntax: log <filename>
unlock Unlocks a device. Syntax: unlock <DeviceName>
Type unlock without <DeviceName> to get a list
of supported device names.
nRESET has to be connected
---- CP15 ------------
rce Read CP15. Syntax: rce <Op1>, <CRn>, <CRm>, <Op2>(读CP15)
wce Write CP15. Syntax: wce <Op1>, <CRn>, <CRm>, <Op2>, <Data>(写CP15)
---- ICE -------------
Ice Show state of the embedded ice macrocell (ICE breaker)
ri Read Ice reg. Syntax: ri <RegIndex>(hex)
wi Write Ice reg. Syntax: wi <RegIndex>, <Data>(hex)
---- ETM -------------
etm Show ETM status
re Read ETM reg. Syntax: re <RegIndex>
we Write ETM reg. Syntax: we <RegIndex>, <Data>(hex)
es Start trace
---- ETB -------------
etb Show ETB status
rb Read ETB register. Syntax: rb <RegIndex>
wb Write ETB register. Syntax: wb <RegIndex>, <Data>(hex)
---- TRACE -----------
TAddBranch TRACE - Add branch instruction to trace buffer. Paras:<Addr>,<BAddr>
TAddInst TRACE - Add (non-branch) instruction to trace buffer. Syntax: <Addr>
TClear TRACE - Clear buffer
TSetSize TRACE - Set Size of trace buffer
TSetFormat TRACE - SetFormat
TSR TRACE - Show Regions (and analyze trace buffer)
TStart TRACE - Start
TStop TRACE - Stop
---- SWO -------------
SWOSpeed SWO - Show supported speeds
SWOStart SWO - Start
SWOStop SWO - Stop
SWOStat SWO - Display SWO status
SWORead SWO - Read and display SWO data
SWOShow SWO - Read and analyze SWO data
SWOFlush SWO - Flush data
---- File I/O --------
fwrite Write file to emulator
fread Read file from emulator
fshow Read and display file from emulator
fdelete Delete file on emulator
fsize Display size of file on emulator
---- Test ------------
thg Run go/halt 1000 times
ts Run step 1000 times
testwspeed Test download speed. Syntax: testwspeed [<Addr> [<Size>]]
testrspeed Test upload speed. Syntax: testrspeed [<Addr> [<Size>] [<NumBlock
s>]]
testcspeed Test CPU speed. Syntax: testcspeed [<RAMAddr>]
---- JTAG ------------
Config Set number of IR/DR bits before ARM device.
Syntax: Config <IRpre>, <DRpre>
speed Set JTAG speed. Syntax: speed <freq>|auto|adaptive, e.g. speed 2000,
speed a
i Read JTAG Id (Host CPU)
wjc Write JTAG command (IR). Syntax: wjc <Data>(hex)
wjd Write JTAG data (DR). Syntax: wjd <Data32>(hex), <NumBits>(dec)
RTAP Reset TAP Controller using state machine (111110)
wjraw Write Raw JTAG data. Syntax: wjraw <NumBits(dec)>, <tms>, <tdi>
rt Reset TAP Controller (nTRST)
---- JTAG-Hardware ---
c00 Create clock with TDI = TMS = 0
c Clock
0 Clear TDI
1 Set TDI
t0 Clear TMS
t1 Set TMS
trst0 Clear TRST
trst1 Set TRST
r0 Clear RESET
r1 Set RESET
---- Connection ------
usb Connect to J-Link via USB. Syntax: usb <port>, where port is 0..3
ip Connect to J-Link ARM Pro or J-Link TCP/IP Server via TCP/IP.
Syntax: ip <ip_addr>
---- Configuration ---
si Select target interface. Syntax: si <Interface>,
where 0=JTAG and 1=SWD.
power Switch power supply for target. Syntax: power <State> [perm],
where State is either On or Off. Example: power on perm
wconf Write configuration byte. Syntax: wconf <offset>, <data>
rconf Read configuration bytes. Syntax: rconf
usbaddr Assign usb address to the connected J-Link: Syntax: usbaddr = <addr>
ipaddr Show/Assign IP address and subnetmask of/to the connected J-Link.
gwaddr Show/Assign network gateway address of/to the connected J-Link.
dnsaddr Show/Assign network DNS server address of/to the connected J-Link.
conf Show configuration of the connected J-Link.
ecp Enable the J-Link control panel.
calibrate Calibrate the target current measurement.
selemu Select a emulator to communicate with,
from a list of all emulators which are connected to the host
The interfaces to search on, can be specified
Syntax: selemu [<Interface0> <Interface1> ...]
ShowEmuList Shows a list of all emulators which are connected to the host.
The interfaces to search on, can be specified.
Syntax: ShowEmuList [<Interface0> <Interface1> ...]
----------------------
NOTE: Specifying a filename in command line
will start J-Link Commander in script mode.
几个常用命令:
usb--------连接目标板
r----------重启目标板
halt-------停止cpu运行的程序
loadbin----加载可执行的二进制文件
g----------跳到代码段地址执行
s----------单步执行(调试用)
setpc-----设置pc寄存器的值(调试用)
setbp-----设置断点
Regs-------读寄存器组织
wreg-------写寄存器
mem--------读内存
w4---------写内存
power off mmu---关闭mmu,这个对于裸板调试很重要
w4 cpsr,0x0000001f------切换到系统模式
speed------设置jtag的传输速率
rce 0,c0,c0,0-----设置cp15寄存器的第1个寄存器为0