#! /bin/bash
# This script is created by DQE Ghosty Liu 2020/08/10 #
### RW
TEST PARAMETER ###
PARTITION="sdb1"
declare -i RW_count=1
declare -i RW_cycle=1 #(1 cycle = 128 MB)
Check_Flag=1 #(1 = check disk scan result; 0 = not check disk scan result)
Remove_Flag=1 #(1 = remove
test file; 0 = not remove
test file)
### PKTGEN
TEST PARAMETER ###
PAIRS="ens8f0-ens8f1-8 enp2s0f0-enp2s0f1-9 enp130s0f0-enp130s0f1-10 ens5f0-ens5f1-11 ens5f2-ens5f3-12" #(port-port-core)
JUMBO=y
declare -i TIME=30
### STRESS
TEST PARAMETER ###
COMMAND="stress -c 4 -m 4 --vm-bytes 1024M -t 60"
declare -i CYCLE=20 #(1 cycle = 3 seconds)
### PING
TEST PARAMETER ###
declare -i PING_COUNT=10
### RTC WAKE PARAMETER ###
declare -i delay=30 # <Decide the RTC wake up delay time here.>
### SPECIAL SCAN PARAMETER ###
check_item="error" # <Add other check item for SPECIAL_SCAN here.>
##########################################################################################################
function DD() {
for k in $(seq $RW_count `
expr $RW_cycle - 1`)
do
if [ ! -z "$k" ]
then
dd if=/dev/zero of=/$partition/$count.$k.tmp bs=32M count=4 conv=fsync &> /dev/null &
fi
done
dd if=/dev/zero of=/$partition/$count.$RW_cycle.tmp bs=32M count=4 conv=fsync &> /dev/null
}
function RW_
TEST() {
if [ "$count" -gt "1" ] && [ "$Check_Flag" -eq "1" ]
then
echo -e "Check DISK SCAN reeult ..."
if [ -z "`diff -q /
Test/CYCLE_LOG/DISK_SCAN/1.log /
Test/CYCLE_LOG/DISK_SCAN/$count.log`" ]
then
echo -e "Check Pass."
else
echo -e "Check failed. RW
Test will be terminated."
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/rw_
test_fail.log
echo -e "Check failed. RW
Test had been skipped." >> /
Test/CYCLE_LOG/rw_
test_fail.log
return 1
fi
fi
echo -e "Start Storage R/W
Test ..."
if [ ! -d "/
Test/CYCLE_LOG/RW_
TEST" ]
then
mkdir -p /
Test/CYCLE_LOG/RW_
TEST
fi
for partition in $PARTITION
do
if [ ! -d "/
Test/CYCLE_LOG/RW_
TEST/$partition" ]
then
mkdir -p /
Test/CYCLE_LOG/RW_
TEST/$partition
fi
if [ ! -z "`ls /dev/
| grep $partition`" ]
|| [ ! -d "/$partition" ]
then
mkdir -p /$partition
if [ -z "`mount
| grep $partition`" ]
then
mount /dev/$partition /$partition
else
if [ ! -z "`mount
| grep $partition
| grep /mnt/hdd`" ]
then
echo "Please make sure that Partition: $partition is not used by
Testbed!"
rm -rf /$partition
rm -rf /
Test/CYCLE_LOG/RW_
TEST/$partition
continue
fi
fi
echo "COUNT : $count" >> /
Test/CYCLE_LOG/RW_
TEST/$partition/result.log
(time -p DD) 2>> /
Test/CYCLE_LOG/RW_
TEST/$partition/result.log &
sleep 1
fi
done
while [ 1 ]
do
buf=`ps -aux
| grep -i "/dev/zero"
| wc -l`
if [ "$buf" -eq "1" ]
then
break
fi
sleep 1
done
sync
sleep 5
for partition in $PARTITION
do
if [ -d "/$partition" ]
then
if [ "$Remove_Flag" -eq "1" ]
then
rm -rf /$partition/*
sync
fi
umount /$partition
fi
done
if [ ! -z "`dmesg
| grep -i ata
| grep -i error`" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/rw_
test_fail.log
dmesg
| grep -i ata
| grep -i error >> /
Test/CYCLE_LOG/rw_
test_fail.log
fi
}
function PKTGEN_
TEST() {
echo -e "Start PKTGEN
Test ..."
if [ ! -d "/
Test/CYCLE_LOG/PKTGEN_
TEST" ]
then
mkdir -p /
Test/CYCLE_LOG/PKTGEN_
TEST
fi
if [ -z "`lsmod
| grep pkt`" ]
then
echo "Please install pktgen driver first!!"
exit 1
fi
for pair in $PAIRS
do
PORT_A=`echo $pair
| cut -d "-" -f 1`
PORT_B=`echo $pair
| cut -d "-" -f 2`
CPU_NUM=`echo $pair
| cut -d "-" -f 3`
ifconfig $PORT_A up
ifconfig $PORT_B up
if [ "$count" -le "1" ]
then
echo $PORT_A >> /
Test/CYCLE_LOG/ethernet_port.list
echo $PORT_B >> /
Test/CYCLE_LOG/ethernet_port.list
fi
echo "rem_device_all" > /proc/net/pktgen/kpktgend_$CPU_NUM
echo "add_device $PORT_A" > /proc/net/pktgen/kpktgend_$CPU_NUM
echo "add_device $PORT_B" > /proc/net/pktgen/kpktgend_$CPU_NUM
echo "max_before_softirq 10000" > /proc/net/pktgen/kpktgend_$CPU_NUM
if [ ! -f "/proc/net/pktgen/$PORT_A" ]
|| [ ! -f "/proc/net/pktgen/$PORT_B" ]
then
echo "Fail to add $pair to pktgen"
exit 1
fi
echo "count 0" > /proc/net/pktgen/$PORT_A
echo "count 0" > /proc/net/pktgen/$PORT_B
if [ "$JUMBO" == "y" ]
then
ifconfig $PORT_A mtu 9000 up
ifconfig $PORT_B mtu 9000 up
echo "pkt_size 9014" > /proc/net/pktgen/$PORT_A
echo "pkt_size 9014" > /proc/net/pktgen/$PORT_B
else
echo "pkt_size 1514" > /proc/net/pktgen/$PORT_A
echo "pkt_size 1514" > /proc/net/pktgen/$PORT_B
fi
echo "delay 100" > /proc/net/pktgen/$PORT_A
echo "delay 100" > /proc/net/pktgen/$PORT_B
echo "dst_mac `ifconfig $PORT_B
| grep ether
| tr -s " "
| cut -d " " -f 3`" > /proc/net/pktgen/$PORT_A
echo "dst_mac `ifconfig $PORT_A
| grep ether
| tr -s " "
| cut -d " " -f 3`" > /proc/net/pktgen/$PORT_B
done
sleep 10
echo start > /proc/net/pktgen/pgctrl &
declare -i buf=`cat /sys/class/rtc/rtc0/since_epoch`
buf=$buf
+$TIME
while [ 1 ]
do
if [ "`cat /sys/class/rtc/rtc0/since_epoch`" -le "$buf" ]
then
sleep 1
else
break
fi
done
kill -9 $!
sleep 1
for i in `cat /
Test/CYCLE_LOG/ethernet_port.list`
do
if [ ! -f "/
Test/CYCLE_LOG/PKTGEN_
TEST/$i" ]
then
mkdir -p /
Test/CYCLE_LOG/PKTGEN_
TEST/$i
fi
ethtool -S $i
| grep -i crc > /
Test/CYCLE_LOG/PKTGEN_
TEST/$i/CRC_$count.log
cat /proc/net/pktgen/$i > /
Test/CYCLE_LOG/PKTGEN_
TEST/$i/PKTGEN_$count.log
for j in `cat /
Test/CYCLE_LOG/PKTGEN_
TEST/$i/CRC_$count.log`
do
declare -i buf=`echo $j
| cut -d ":" -f 2
| cut -d " " -f 2`
if [ "$buf" -gt "0" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/pktgen_
test_fail.log
echo "$i pktgen
test result has CRC errors." >> /
Test/CYCLE_LOG/pktgen_
test_fail.log
fi
done
sync
done
}
function TIME_STAMP() {
if [ "$count" -eq "1" ]
then
cat /sys/class/rtc/rtc0/since_epoch > /
Test/CYCLE_LOG/time_stamp_tmp.log
echo "$count: 0" > /
Test/CYCLE_LOG/time_stamp.log
else
declare -i Ntime=`cat /sys/class/rtc/rtc0/since_epoch`
declare -i Otime=`cat /
Test/CYCLE_LOG/time_stamp_tmp.log`
echo "$count: `
expr $Ntime - $Otime`" >> /
Test/CYCLE_LOG/time_stamp.log
echo $Ntime > /
Test/CYCLE_LOG/time_stamp_tmp.log
fi
}
function STRESS() {
echo -e "Start Stress
Test ..."
sleep 3
$COMMAND &
top -d 3 -n $CYCLE
clear
}
function DMESG() {
if [ ! -d "/
Test/CYCLE_LOG/DMESG" ]
then
mkdir -p /
Test/CYCLE_LOG/DMESG
fi
dmesg > /
Test/CYCLE_LOG/DMESG/$count.log
sync
}
function PING_
TEST() {
echo -e "Start PING
Test ..."
if [ ! -d "/
Test/CYCLE_LOG/PING_
TEST" ]
then
mkdir -p /
Test/CYCLE_LOG/PING_
TEST
fi
if [ ! -f "/
Test/ping.config" ]
then
echo "Couldn't find ping.config on path /
Test! Stop PING_
TEST..."
sleep 3
break
else
Ping_item=`cat /
Test/ping.config` # <The ping.config shall be "name1_source-address1_destination-address1 name2_source-address2_destination-address2 ...".>
for i in $Ping_item
do
ETH_NAME=`echo $i
| cut -d "_" -f 1`
S_ADDRESS=`echo $i
| cut -d "_" -f 2`
D_ADDRESS=`echo $i
| cut -d "_" -f 3`
ifconfig $ETH_NAME $S_ADDRESS up
sleep 3
echo -e "\n$ETH_NAME ping $D_ADDRESS
test..."
ping -I $ETH_NAME $D_ADDRESS -c $PING_COUNT >> /
Test/ping.$ETH_NAME.[$D_ADDRESS].tmp &
done
fi
while [ 1 ]
do
Buf=`ps
| grep -i eth
| wc -l`
if [ "$Buf" = "1" ]
then
sleep 3
break
fi
done
Buf_stress=`ps
| grep -i stress
| wc -l`
if [ "$Buf_stress" -ne "1" ]
then
pkill stress
fi
Ping_tmp=`ls /
Test | grep -i .tmp`
for i in $Ping_tmp
do
if [ ! -f "/
Test/CYCLE_LOG/PING_
TEST/$i" ]
then
mkdir -p /
Test/CYCLE_LOG/PING_
TEST/$i
fi
j=`echo $i
| cut -d "." -f 2`
cat /
Test/$i >> /
Test/CYCLE_LOG/PING_
TEST/$i/$count.log
if [ -z "`cat /
Test/$i
| grep -i ttl=`" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/ping_
test_fail.log
echo "$i ping
test failed." >> /
Test/CYCLE_LOG/ping_
test_fail.log
cat /
Test/$i >> /
Test/CYCLE_LOG/ping_
test_fail.log
echo " " >> /
Test/CYCLE_LOG/ping_
test_fail.log
ifconfig $j >> /
Test/CYCLE_LOG/ping_
test_fail.log
echo " " >> /
Test/CYCLE_LOG/ping_
test_fail.log
ethtool $j >> /
Test/CYCLE_LOG/ping_
test_fail.log
echo "=====================================================" >> /
Test/CYCLE_LOG/ping_
test_fail.log
fi
rm -rf /
Test/$i
done
sync
sleep 1
}
function SPECIAL_SCAN() {
if [ ! -d "/
Test/CYCLE_LOG/SPECIAL_SCAN" ]
then
mkdir -p /
Test/CYCLE_LOG/SPECIAL_SCAN
fi
for i in `echo $check_item`
do
dmesg
| grep -i $i
| cut -d "]" -f 2 >> /
Test/CYCLE_LOG/SPECIAL_SCAN/$count.log
dmesg
| grep -i $i >> /
Test/CYCLE_LOG/special_scan.log
done
echo "=====================================================" >> /
Test/CYCLE_LOG/special_scan.log
if [ -f "/
Test/CYCLE_LOG/SPECIAL_SCAN/1.log" ]
then
BUFFER=`diff -q /
Test/CYCLE_LOG/SPECIAL_SCAN/1.log /
Test/CYCLE_LOG/SPECIAL_SCAN/$count.log`
if [ ! -z "$BUFFER" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/SPECIAL_SCAN_fail.log
diff /
Test/CYCLE_LOG/SPECIAL_SCAN/1.log /
Test/CYCLE_LOG/SPECIAL_SCAN/$count.log >> /
Test/CYCLE_LOG/SPECIAL_SCAN_fail.log
echo " " >> /
Test/CYCLE_LOG/SPECIAL_SCAN_fail.log
fi
fi
sync
sleep 1
}
function USB_SCAN() {
echo -e "Scanning USB devices ..."
if [ ! -d "/
Test/CYCLE_LOG/USB_SCAN" ]
then
mkdir -p /
Test/CYCLE_LOG/USB_SCAN
fi
lsusb -tvv >> /
Test/CYCLE_LOG/USB_SCAN/$count.log
lsusb -tvv >> /
Test/CYCLE_LOG/usb_scan.log
echo "=====================================================" >> /
Test/CYCLE_LOG/usb_scan.log
if [ -f "/
Test/CYCLE_LOG/USB_SCAN/1.log" ]
then
BUFFER=`diff -q /
Test/CYCLE_LOG/USB_SCAN/1.log /
Test/CYCLE_LOG/USB_SCAN/$count.log`
if [ ! -z "$BUFFER" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/USB_SCAN_fail.log
diff /
Test/CYCLE_LOG/USB_SCAN/1.log /
Test/CYCLE_LOG/USB_SCAN/$count.log >> /
Test/CYCLE_LOG/USB_SCAN_fail.log
echo " " >> /
Test/CYCLE_LOG/USB_SCAN_fail.log
fi
fi
#/
Test/67b-usblist.sh >> /
Test/CYCLE_LOG/tb_usblist.log
sync
sleep 1
}
function DRIVER_INSTALL() {
for i in /
Test/*.ko
do
insmod $i
done
sleep 1
}
function PCIE_SCAN() {
echo -e "\nScanning PCIe devices ..."
if [ ! -d "/
Test/CYCLE_LOG/PCIE_SCAN" ]
then
mkdir -p /
Test/CYCLE_LOG/PCIE_SCAN
fi
for i in `lspci
| sed 's/ /_/g'`
do
DEVICE=`echo $i
| cut -d "_" -f 1`
LNK_CAP_SPEED=`lspci -s $DEVICE -vv
| grep LnkCap:
| cut -d ":" -f 2
| cut -d "," -f 2`
LNK_CAP_WIDTH=`lspci -s $DEVICE -vv
| grep LnkCap:
| cut -d ":" -f 2
| cut -d "," -f 3`
LNK_STA_SPEED=`lspci -s $DEVICE -vv
| grep LnkSta:
| cut -d ":" -f 2
| cut -d "," -f 1`
LNK_STA_WIDTH=`lspci -s $DEVICE -vv
| grep LnkSta:
| cut -d ":" -f 2
| cut -d "," -f 2`
if [ ! -z "$LNK_CAP_SPEED" ] && [ ! -z "$LNK_STA_SPEED" ]
then
echo "$i : CAPABILITY=$LNK_CAP_SPEED, $LNK_CAP_WIDTH & STATUS=$LNK_STA_SPEED, $LNK_STA_WIDTH" >> /
Test/CYCLE_LOG/PCIE_SCAN/$count.log
echo "$i : CAPABILITY=$LNK_CAP_SPEED, $LNK_CAP_WIDTH & STATUS=$LNK_STA_SPEED, $LNK_STA_WIDTH" >> /
Test/CYCLE_LOG/pcie_scan.log
else
echo "$i :" >> /
Test/CYCLE_LOG/PCIE_SCAN/$count.log
echo "$i :" >> /
Test/CYCLE_LOG/pcie_scan.log
fi
done
echo "Total count = `lspci
| wc -l`" >> /
Test/CYCLE_LOG/PCIE_SCAN/$count.log
echo "Total count = `lspci
| wc -l`" >> /
Test/CYCLE_LOG/pcie_scan.log
echo "=====================================================" >> /
Test/CYCLE_LOG/pcie_scan.log
if [ -f "/
Test/CYCLE_LOG/PCIE_SCAN/1.log" ]
then
BUFFER=`diff -q /
Test/CYCLE_LOG/PCIE_SCAN/1.log /
Test/CYCLE_LOG/PCIE_SCAN/$count.log`
if [ ! -z "$BUFFER" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/PCIE_SCAN_fail.log
diff /
Test/CYCLE_LOG/PCIE_SCAN/1.log /
Test/CYCLE_LOG/PCIE_SCAN/$count.log >> /
Test/CYCLE_LOG/PCIE_SCAN_fail.log
echo " " >> /
Test/CYCLE_LOG/PCIE_SCAN_fail.log
fi
fi
#/
Test/64a-get_pcilist.sh >> /
Test/CYCLE_LOG/tb_pcilist.log
sync
sleep 1
}
function DISK_SCAN() {
echo -e "Scanning Storage devices ..."
if [ ! -d "/
Test/CYCLE_LOG/DISK_SCAN" ]
then
mkdir -p /
Test/CYCLE_LOG/DISK_SCAN
fi
for i in `ls /sys/block/`
do
if [ -f "/sys/block/$i/device/model" ]
then
if [ ! -z "$(cat /sys/block/$i/device/model
| grep -v Virtual)" ]
then
SIZE=$(
expr `cat /sys/block/$i/size` \* 512)
echo -e "$i : `cat /sys/block/$i/device/model`\t Size = $SIZE Byte" >> /
Test/CYCLE_LOG/DISK_SCAN/$count.log
echo -e "$i : `cat /sys/block/$i/device/model`\t Size = $SIZE Byte" >> /
Test/CYCLE_LOG/disk_scan.log
fi
elif [ -f "/sys/block/$i/device/name" ]
then
SIZE=$(
expr `cat /sys/block/$i/size` \* 512)
echo -e "$i : `cat /sys/block/$i/device/name`\t Size = $SIZE Byte" >> /
Test/CYCLE_LOG/DISK_SCAN/$count.log
echo -e "$i : `cat /sys/block/$i/device/name`\t Size = $SIZE Byte" >> /
Test/CYCLE_LOG/disk_scan.log
fi
done
echo "=====================================================" >> /
Test/CYCLE_LOG/disk_scan.log
if [ -f "/
Test/CYCLE_LOG/DISK_SCAN/1.log" ]
then
BUFFER=`diff -q /
Test/CYCLE_LOG/DISK_SCAN/1.log /
Test/CYCLE_LOG/DISK_SCAN/$count.log`
if [ ! -z "$BUFFER" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/DISK_SCAN_fail.log
diff /
Test/CYCLE_LOG/DISK_SCAN/1.log /
Test/CYCLE_LOG/DISK_SCAN/$count.log >> /
Test/CYCLE_LOG/DISK_SCAN_fail.log
echo " " >> /
Test/CYCLE_LOG/DISK_SCAN_fail.log
fi
fi
#/
Test/66a-get_hddlist.sh >> /
Test/CYCLE_LOG/tb_hddlist.log
sync
sleep 1
}
function MAC_SCAN() {
echo -e "Scanning Ethernet port MAC address ..."
if [ ! -d "/
Test/CYCLE_LOG/MAC_SCAN" ]
then
mkdir -p /
Test/CYCLE_LOG/MAC_SCAN
fi
for i in `ls /sys/class/net/`
do
if [ -d "/sys/class/net/$i/device" ]
then
echo -e "$i\t : `cat /sys/class/net/$i/address`" >> /
Test/CYCLE_LOG/MAC_SCAN/$count.log
echo -e "$i\t : `cat /sys/class/net/$i/address`" >> /
Test/CYCLE_LOG/mac_scan.log
fi
done
echo "=====================================================" >> /
Test/CYCLE_LOG/mac_scan.log
if [ -f "/
Test/CYCLE_LOG/MAC_SCAN/1.log" ]
then
BUFFER=`diff -q /
Test/CYCLE_LOG/MAC_SCAN/1.log /
Test/CYCLE_LOG/MAC_SCAN/$count.log`
if [ ! -z "$BUFFER" ]
then
echo "COUNT=$count :" >> /
Test/CYCLE_LOG/MAC_SCAN_fail.log
diff /
Test/CYCLE_LOG/MAC_SCAN/1.log /
Test/CYCLE_LOG/MAC_SCAN/$count.log >> /
Test/CYCLE_LOG/MAC_SCAN_fail.log
echo " " >> /
Test/CYCLE_LOG/MAC_SCAN_fail.log
fi
fi
sync
sleep 1
}
function CLEAR_LOG() {
if [ -d "/
Test/CYCLE_LOG" ]
then
DATE=`date
| sed 's/ /_/g'
| sed 's/:/_/g'
| sed 's/__/_/g'`
mkdir -p /
Test/$DATE
mv /
Test/CYCLE_LOG/* /
Test/$DATE
sync
rm -rf /
Test/CYCLE_LOG
fi
}
function DEBUG() {
if [ "$1" = "disk" ]
|| [ "$1" = "DISK" ]
then
DISK_SCAN
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/DISK_SCAN/1.log
echo "-------------------------------------------"
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "pcie" ]
|| [ "$1" = "PCIE" ]
then
PCIE_SCAN
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/PCIE_SCAN/1.log
echo "-------------------------------------------"
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "usb" ]
|| [ "$1" = "USB" ]
then
USB_SCAN
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/USB_SCAN/1.log
echo "-------------------------------------------"
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "special" ]
|| [ "$1" = "SPECIAL" ]
then
SPECIAL_SCAN
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/SPECIAL_SCAN/1.log
echo "-------------------------------------------"
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "mac" ]
|| [ "$1" = "MAC" ]
then
MAC_SCAN
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/MAC_SCAN/1.log
echo "-------------------------------------------"
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "rw" ]
|| [ "$1" = "RW" ]
then
RW_
TEST
echo "-------------------------------------------"
for i in $PARTITION
do
if [ -d "/$i" ]
then
cat /
Test/CYCLE_LOG/RW_
TEST/$i/result.log
else
echo "Partition: $i could not be
tested!"
fi
done
echo "-------------------------------------------"
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "ping" ]
|| [ "$1" = "PING" ]
then
Ping_item=`cat /
Test/ping.config`
PING_
TEST
Log_list=`ls /
Test/CYCLE_LOG/PING_
TEST`
for i in $Log_list
do
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/PING_
TEST/$i/1.log
echo "-------------------------------------------"
done
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "stress" ]
|| [ "$1" = "STRESS" ]
then
STRESS
elif [ "$1" = "pktgen" ]
|| [ "$1" = "PKTGEN" ]
then
PKTGEN_
TEST
for i in `cat /
Test/CYCLE_LOG/ethernet_port.list`
do
echo "-------------------------------------------"
cat /
Test/CYCLE_LOG/PKTGEN_
TEST/$i/CRC_1.log
cat /
Test/CYCLE_LOG/PKTGEN_
TEST/$i/PKTGEN_1.log
echo "-------------------------------------------"
done
rm -rf /
Test/CYCLE_LOG/*
elif [ "$1" = "clean" ]
|| [ "$1" = "CLEAN" ]
then
CLEAR_LOG
else
mkdir -p /
Test/CYCLE_LOG
echo $1 > /
Test/CYCLE_LOG/goal.tmp
echo $2 > /
Test/CYCLE_LOG/power_cycle.tmp
fi
}
function POWER_CYCLE() {
COMMAND=`cat /
Test/CYCLE_LOG/power_cycle.tmp`
if [ $COMMAND == poweroff ]
then
echo 0 > /sys/class/rtc/rtc0/wakealarm
echo `
expr $(date
+%s)
+ $delay` > /sys/class/rtc/rtc0/wakealarm
$COMMAND
else
$COMMAND
fi
}
if [ -z "$1" ]
then
if [ -f "/
Test/CYCLE_LOG/goal.tmp" ] && [ -f "/
Test/CYCLE_LOG/power_cycle.tmp" ]
then
#DRIVER_INSTALL
declare -i goal=`cat /
Test/CYCLE_LOG/goal.tmp`
declare -i count
if [ ! -d "/
Test/CYCLE_LOG" ]
then
mkdir -p /
Test/CYCLE_LOG
fi
if [ ! -f "/
Test/CYCLE_LOG/count.log" ]
then
echo 1 > /
Test/CYCLE_LOG/count.log
echo 1 > /
Test/CYCLE_LOG/first.tmp
fi
count=`cat /
Test/CYCLE_LOG/count.log`
if [ ! -f "/
Test/CYCLE_LOG/FLAG01" ] && [ ! -f "/
Test/CYCLE_LOG/first.tmp" ]
then
echo "The $count times
test is not finished correctly!" >> /
Test/CYCLE_LOG/Warnning.log
count
+=1
echo $count > /
Test/CYCLE_LOG/count.log
else
if [ -f "/
Test/CYCLE_LOG/FLAG01" ]
then
rm -rf /
Test/CYCLE_LOG/FLAG01
fi
fi
if [ ! -f "/
Test/CYCLE_LOG/FLAG02" ] && [ ! -f "/
Test/CYCLE_LOG/first.tmp" ]
then
if [ ! -z "`ls /
Test/CYCLE_LOG/PCIE_SCAN/
| grep $count.log`" ]
then
count
+=1
echo $count > /
Test/CYCLE_LOG/count.log
fi
else
if [ -f "/
Test/CYCLE_LOG/FLAG02" ]
then
rm -rf /
Test/CYCLE_LOG/FLAG02
fi
fi
sync
if [ -f "/
Test/CYCLE_LOG/first.tmp" ]
then
rm -rf /
Test/CYCLE_LOG/first.tmp
fi
clear
echo "******************************************************"
echo "* *"
echo "* System is starting the $count times cycle
test ... "
echo "* *"
echo "******************************************************"
read -p "Press [c] to stop
testing! " -t 5 -n 1 stop
if [ "$stop" = "c" ]
then
echo 0 > /sys/class/rtc/rtc0/wakealarm
CLEAR_LOG
exit 0
fi
PCIE_SCAN
DISK_SCAN
#RW_
TEST
USB_SCAN
MAC_SCAN
SPECIAL_SCAN
#PKTGEN_
TEST
#STRESS
#PING_
TEST
DMESG
TIME_STAMP
if [ "$count" -ge "$goal" ]
then
CLEAR_LOG
clear
echo "******************************************************"
echo "* *"
echo "* The power cycle
test has been finished! *"
echo "* *"
echo "******************************************************"
read -p "Press any key to continue! " -n 1 continue
else
echo 1 > /
Test/CYCLE_LOG/FLAG01
count
+=1
echo $count > /
Test/CYCLE_LOG/count.log
echo 1 > /
Test/CYCLE_LOG/FLAG02
sync
clear
echo "******************************************************"
echo "* *"
echo "* The `
expr $count - 1` times cycle
test is completed ... "
echo "* *"
echo "******************************************************"
sleep 1
POWER_CYCLE
fi
fi
else
declare -i count=1
if [ -z "$2" ]
then
DEBUG $1
else
DEBUG $1 $2
fi
fi
帮忙将这个脚本优化一下，我只是用来计数开关机的次数，只要开机能显示执行了多少次的效果，其他多余的部分请帮忙删除
扫一扫
511
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
