FPGA综合后警告问题说明

最新推荐文章于 2024-11-28 19:23:15 发布

不够努力的人

最新推荐文章于 2024-11-28 19:23:15 发布

阅读量3.2k

点赞数

CC 4.0 BY-SA版权

文章标签：报告中的警告说明需要修改的警告

本文链接：https://blog.youkuaiyun.com/weixin_44270744/article/details/88410126

本文解析了VHDL设计与仿真过程中常见的警告信息，包括信号未放入process、时钟约束缺失、门控时钟问题、组合逻辑闭环等，提供了详细的解决建议。

摘要生成于 C知道，由 DeepSeek-R1 满血版支持，前往体验 >

Warning: VHDL Process Statement warning at random.vhd(18): signal reset is in statement, but is not in sensitivity list

【提示】没把singal放到process（）中。

2.Warning: Found pins ing as undefined clocks and/or memory enables
Info: Assuming node CLK is an undefined clock
【提示】是说设计中没有对时钟进行约束。【解决】在assignment/timing anlaysis setting/inidividual clock中设置

Warning: Found 2 node(s) in clock paths which may be acting as ripple and/or gated clocks – node(s) analyzed as buffer(s) resulting in clock skew
Info: Detected ripple clock "clk_gen:clk_gen1|clk_incr" as buffer
Info: Detected ripple clock "clk_gen:clk_gen1|clk_scan" as buffer
【提示】设计中出现门控时钟问题，最好修掉，时钟分析会更容易通过，系统更稳。如果是必须的，可以忽略此提示。
Warning: VHDL Process Statement warning at ledmux.vhd(15): signal or variable "dataout" may not be assigned a new in every possible path through the Process Statement. Signal or variable "dataout" holds its previous in every path with no new assignment, which may create a combinational loop in the current design.
【提示】电路设计里面出现了组合逻辑信号反馈的一个闭环。这样没有经过寄存器的反馈会造成电路很不稳定，很容易出现毛刺。建议修改。
Warning: No clock transition on "counter_bcd7:counter_counter_clk|q_sig[3]" register
【提示】寄存器没有接时钟。
Warning: Reduced register "counter_bcd7:counter_counter_clk|q_sig[3]" with stuck clock port to stuck GND
【提示】寄存器没有赋值，软件自动将输入接GND。
Warning: Circuit may not operate. Detected 1 non-operational path(s) clocked by clock "class[1]" with clock skew larger than data delay. See Compilation Report for details.
【提示】时序分析中出现的warning，提示clock skew太大，严重影响到时序，建议查出原因坚决修掉。具体原因要参考report。
Warning: Ignored node in vector source file. Can’t find corresponding node name “class_sig[2]” in design.
【提示】所提示的信号没有连接或定义到高层。
Warning: Found clock high time violation at 1000.0 ns on register "|fcounter|lpm_counter:temp_rtl_0|dffs[4]"
【提示】仿真中出现的，提示时序很紧，适当降低主时钟频率再仿真。
Warning: Compiler packed, optimized or synthesized away node "temp[19]". Ignored vector source file node.
【提示】信号没有最终使用，被软件自动优化去掉了。
Warning: Design contains 2 input pin(s) that do not drive logic
Warning: No output dependent on input pin "clk"
Warning: No output dependent on input pin "sign"
【提示】两个信号在电路中未被使用，没有驱动任何电路，最终也会被优化掉。
Warning: Ignored node in vector source file. Can’t find corresponding node name “over” in design.
【提示】在源文件中找不到对应的节点“over”。