Redirection

Typically, the syntax of these characters is as follows, using < to redirect input, and > to redirect output.

command1 > file1

executes command1, placing the output in file1, as opposed to displaying it at the terminal, which is the usual destination for standard output. This will clobber any existing data in file1.

Using

command1 < file1

executes command1, with file1 as the source of input, as opposed to thekeyboard, which is the usual source for standard input.

command1 < infile > outfile

combines the two capabilities: command1 reads from infile and writes tooutfile

Variants[edit]

To append output to the end of the file, rather than clobbering it, use the>> operator:

command1 >> file1

To read from a stream literal (an inline file, passed to the standard input), one can use a here document, using the << operator:

tr a-z A-Z << END_TEXT
one two three
uno dos tres
END_TEXT

To read from a string, one can use a here string, using the <<< operator:

tr a-z A-Z <<< "one two three"

or:

NUMBERS="one two three"
tr a-z A-Z <<< "$NUMBERS"

转载于:https://www.cnblogs.com/vigorz/p/10499099.html

<think>好的,用户想了解如何在BIOS中配置Console Redirection功能。我需要结合之前的引用内容来整理步骤。首先,引用1提到Console Redirection通常只在POST和BIOS环境下有效,而要在OS层面使用需要修改启动参数。引用3详细列出了进入BIOS设置、修改GRUB配置、调整inittab和securetty文件等步骤。引用2和4也提到了BIOS中的具体选项位置,比如Server Management下的Console Redirection设置。 用户可能是在管理服务器,需要远程访问BIOS和操作系统信息。他们可能已经尝试过部分设置,但可能遇到无法在OS中看到输出的问题,如引用3提到的仅有步骤1和5只能看到BIOS信息,需要其他配置。因此,我需要将步骤分清楚,确保用户完成所有必要的配置,包括BIOS、GRUB、inittab、securetty以及BMC设置,以便在操作系统启动后仍能通过串口重定向访问。 同时,用户可能需要知道如何验证配置是否成功,比如使用ipmitool命令。还要注意不同服务器品牌的BIOS界面可能不同,需要提醒用户参考具体文档。另外,安全方面,修改securetty文件允许串口登录,这也是关键步骤之一,不能遗漏。 总结回答的结构应该是分步骤,从BIOS设置到系统配置,最后验证方法。同时生成的相关问题要覆盖常见后续疑问,比如无法看到启动后信息、串口参数设置、不同品牌的差异等。</think>### 如何在BIOS中配置Console Redirection功能 #### 一、进入BIOS设置 1. **启动服务器时进入BIOS** 开机时按$F2$键(不同品牌可能使用$DEL$、$F10$等键)进入BIOS界面[^3][^4]。 2. **定位Console Redirection选项** - 导航至路径:$Server Management \rightarrow Console Redirection$ - 将选项设置为$Serial Port A$或指定COM端口(如COM2)[^2][^4]。 3. **配置串口参数** - 在$Serial Communication$中启用$On\ with\ Console\ Redirection\ via\ COM2$ - 确保波特率与后续系统配置一致(例如57600)[^4]。 --- #### 二、操作系统层配置 1. **修改GRUB引导参数** - 编辑文件`/boot/grub/grub.conf`或`/boot/grub/menu.lst` - 在$kernel$行末尾添加参数: $$console=ttyS1,57600$$ 示例: ```bash kernel /boot/vmlinuz ro root=/dev/sda1 console=tty0 console=ttyS1,57600 ``` 2. **配置终端登录** - 编辑`/etc/inittab`,添加串口终端: ```bash s0:2345:respawn:/sbin/agetty -h -L 57600 ttyS0 vt100 s1:2345:respawn:/sbin/agetty -h -L 57600 ttyS1 vt100 ``` - 修改`/etc/securetty`,允许串口登录: ```bash ttyS0 ttyS1 ``` [^3] --- #### 三、BMC/IPMI配置(可选) 1. **启用IPMI over LAN** - 在BIOS中找到$Remote\ Access\ Configuration$ - 设置$IPMI\ over\ Lan$为$On$,并配置IP地址和用户权限。 2. **验证远程访问** ```bash ipmitool -U username -I lanplus -H hostip -P "password" sol activate ``` 此命令可激活串口重定向的远程会话[^3]。 --- #### 注意事项 1. **端口一致性** BIOS、GRUB、系统终端的串口号(如COM2对应$ttyS1$)需一致[^3][^4]。 2. **波特率匹配** 确保BIOS、GRUB、终端配置的波特率(如57600)完全相同[^3]。 3. **安全风险** 开放串口登录可能降低系统安全性,建议配合防火墙规则限制访问源[^3]。 ---
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值