MfgTool (i.MX53)使用

最新推荐文章于 2024-02-22 19:00:00 发布

转载最新推荐文章于 2024-02-22 19:00:00 发布 · 100 阅读

CC 4.0 BY-SA版权

原文链接：http://www.cnblogs.com/LoongEmbedded/p/5298279.html

本文介绍了一种使用Freescale的MfgTool进行i.MX53系列模块固件批量烧录的方法。通过该工具可以方便地将固件更新到多个i.MX53模块上，支持CM-i.MX53 Consumer+Industrial及Qseven-i.MX537等型号。文中详细解释了如何下载安装所需软件、连接设备、选择正确的配置文件以及开始固件更新的过程。

摘要生成于 C知道，由 DeepSeek-R1 满血版支持，前往体验 >

1 Introduction

The MfgTool is a manufacturing tool from Freescale that runs under Windows. It is designed to program firmware to i.MX boards for mass production. Boards are connected via USB and execute the USB/UART (Serial downloader) mode.

Bluetechnix added additional profiles to this tool in order to be usable with our i.MX53 modules.

2 Download

MfgTool release 1.6.2.042 by Freescale
- Support for CM-i.MX53 Consumer + Industrial, Qseven-i.MX537 modules
- Target running Linux BSP with Bluetechnix patchset V1.4
- Download here

(DEPRECATED) MfgTool release 1.6.2.032 by Freescale
- Support for CM-i.MX53 Consumer
- Target running Linux BSP with Bluetechnix patchset V1.2
- Download here

You may download the original ZIP file from the Freescale web site - open the Programmers (Flash, etc.) menu!

3 Instructions

Connect the boards' USB-OTG port to a Windows PC. Select USB/UART (Serial Downloader) boot mode on the boards, and power up the boards. The first time you connect, you have to install a Windows device driver. You can find it in the ZIP file, folder Drivers. If you have successful installed the driver, the boards shows up as Freescale i.MX53 USB BulkIO Device in the device manager.

Start MfgTool.exe. Switch on or reset your boards and click on Scan devices. In the field A to D, your boards will show up as Freescale i.MX53 USB BulkIO Device.
In the Profile: drop-down box, select the correct profile for your module
- cmimx53 consumer
- cmimx53 industrial
- qsevenimx537

Select Options-->Configuration... from the menu. There may be several options for the firmware update, choose the desired one as shown on the image below.
- CM-i.MX53 Consumer/Industrial
  - SPI+NAND: Programs the boot loader and the kernel image to SPI flash, the root file system to NAND flash; for SPI flash boot mode.
  - NAND: Programs everything to NAND flash; for NAND boot mode.
- Qseven-i.MX537
  - SPI+NAND: Programs the boot loader to SPI flash, the kernel image to SPI and NAND flash, and the root file system to NAND flash only; for SPI flash boot mode.

Leave the menu and click the green Start button. Now, the firmware update is in progress.

A green progress bar indicates success.

Note that boards may be disconnected and reconnected individually, the tool will monitor them and start a new firmware update each time a new board is connected.

转载于:https://www.cnblogs.com/LoongEmbedded/p/5298279.html