cat /sys/kernel/debug/pinctrl/pinctrl-rockchip-pinctrl/pinmux-pins
cat /sys/kernel/debug/gpio
20251215给飞凌OK3588-C开发板适配Rockchip原厂的Buildroot【linux-5.10】后调通typeC1接口
2025/12/15 20:46
缘起：给飞凌OK3588-C开发板适配Rockchip原厂的Buildroot【linux-6.1】后，调通了type C0。
【通过USB-A母头转TYPE-C公头转接USB3.0接口的U盘来测试！】
调试type C1有点问题。
老是识别不了：不是LCD+HDMI没有显示了！
就是关闭DP之后，结果TYPE C1也彻底不认识了！【插U盘】
公司使用荣品RPO-RK3566+RTL8211F-CG的机器经常出现断联【linux/Buildroot】，需要统计RK3566断联了多少次/是否断联过！
直接现在飞凌OK3588-C开发板上测试了。
飞凌丝印ETH1的地方，在Rockchip原厂的Buildroot【linux-6.1】系统下被识别为eth0了。
飞凌OK3588-C开发板跑Rockchip原厂的Buildroot【linux-6.1】系统时，适配ETH1接口的网卡。
当你把荣品RD-RK3588开发板重新适配一把，就相当于从头做了一个项目：【荣品RD-RK3588开发板】。
当然，开发板的功能都是好的，你免除了调试的过程，也就没有解决相关硬件出错的经验/机会了！
由于飞凌提供了Linux5.10.209内核的buildroot系统。想办法找到linux-5.10内核的buildroot，那就先直接使用Rockchip原厂的Buildroot【linux-5.10】来适配飞凌OK3588-C开发板。
【也许会快点-适配完成/搞定】
E:\OK3588-C_Linux5.10.209+Qt5.15.10_用户资料_R1
首先确认飞凌的OK3588-C_Linux5.10.209+Qt5.15.10，LCD0+HDMI0都可以显示，同时type C0和type C1接USB3.0的U盘也是可以用的！【正常识别USB3.0接口】
直接使用飞凌的DTS，出现了老毛病：LCDO+HDMI0又不显示了，但是type C0和type C1接USB3.0的U盘也是可以用的！【正常识别USB3.0接口】
有信心了！
既然这样，那就搬运飞凌的DTS代码块了！
Y:\new_disk_4t\wyb\RD-RK3588\RK3588_Linux5.10_V1.2.0_20230620\kernel\arch\arm64\boot\dts\rockchip21飞凌R1备份\OK3588-C-common.dtsi
Y:\new_disk_4t\wyb\RD-RK3588\RK3588_Linux5.10_V1.2.0_20230620\kernel\arch\arm64\boot\dts\rockchip\rk3588-evb7-v11.dtsi
1、EVB7V11默认只有一个TYPE C0，我们需要把type C1也适配好！
vbus5v0_typec: vbus5v0-typec {
compatible = "regulator-fixed";
regulator-name = "vbus5v0_typec";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio3 RK_PA6 GPIO_ACTIVE_HIGH>;
vin-supply = <&vcc5v0_usb>;
pinctrl-names = "default";
pinctrl-0 = <&typec5v_pwren>;
};
修改为：
vbus5v0_typec0: vbus5v0-typec0 {
compatible = "regulator-fixed";
regulator-name = "vbus5v0_typec0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio0 RK_PD0 GPIO_ACTIVE_HIGH>;
vin-supply = <&vcc5v0_sys>;
pinctrl-names = "default";
pinctrl-0 = <&typec5v_pwren0>;
};
vbus5v0_typec1: vbus5v0-typec1 {
compatible = "regulator-fixed";
regulator-name = "vbus5v0_typec1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
vin-supply = <&vcc5v0_sys>;
pinctrl-names = "default";
pinctrl-0 = <&typec5v_pwren1>;
};
2、【必须拿掉，和vbus5v0_typec1冲突了，不然启动的时候不能进buildroot的界面！】
//&dsi0_panel {
// power-supply = <&vcc3v3_lcd_n>;
// reset-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
// pinctrl-names = "default";
// pinctrl-0 = <&lcd_rst_gpio>;
//};
3、拿掉CC芯片fusb311，使用fusb302
&i2c5 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c5m2_xfer>;
// ft5x06_dsi1: ft5x06@38 {
// compatible = "edt,edt-ft5406", "edt,edt-ft5x06";
// reg = <0x38>;
// pinctrl-names = "ft5x06_defaults";
// pinctrl-0 = <&ft5x06_dsi2_gpio>;
//// interrupt-parent = <&gpio3>;
//// interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
// irq-gpio = <&gpio3 RK_PD3 GPIO_ACTIVE_HIGH>;
// touchscreen-size-x = <1024>;
// touchscreen-size-y = <600>;
// status = "okay";
// };
//
// gt9xx_dsi1: gt9xx@14 {
// compatible = "goodix,gt911";
// reg = <0x14>;
// pinctrl-names = "gt9xx_default";
// pinctrl-0 = <>911_dsi2_gpio>;
//// interrupt-parent = <&gpio3>;
//// interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
// irq-gpio = <&gpio3 RK_PD3 GPIO_ACTIVE_HIGH>;
// reset-gpio = <&gpio3 RK_PD2 GPIO_ACTIVE_HIGH>;
// touchscreen-size-x = <1024>;
// touchscreen-size-y = <600>;
// is-mutex;
// filter-reg = <0x38>;
// bus-reg = <0x05>;
// status = "okay";
// };
rtc: pcf8563@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
status = "okay";
};
rx8010:rx8010@32 {
compatible = "epson,rx8010";
reg = <0x32>;
status = "okay";
};
usbc1: fusb302@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
interrupt-parent = <&gpio1>;
interrupts = <RK_PB3 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&usbc1_int>;
vbus-supply = <&vbus5v0_typec1>;
status = "okay";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
usbc1_role_sw: endpoint@0 {
remote-endpoint = <&dwc3_1_role_switch>;
};
};
};
usb_con1: connector {
compatible = "usb-c-connector";
label = "USB-C";
data-role = "dual";
power-role = "dual";
try-power-role = "sink";
op-sink-microwatt = <1000000>;
sink-pdos =
<PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
source-pdos =
<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
altmodes {
#address-cells = <1>;
#size-cells = <0>;
altmode@0 {
reg = <0>;
svid = <0xff01>;
vdo = <0xffffffff>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
usbc1_orien_sw: endpoint {
remote-endpoint = <&usbdp_phy1_orientation_switch>;
};
};
port@1 {
reg = <1>;
dp1_altmode_mux: endpoint {
remote-endpoint = <&usbdp_phy1_dp_altmode_mux>;
};
};
};
};
};
};
&i2c6 {
status = "okay";
//usbc0: husb311@4e {
// compatible = "hynetek,husb311";
// reg = <0x4e>;
// interrupt-parent = <&gpio3>;
// interrupts = <RK_PB6 IRQ_TYPE_LEVEL_LOW>;
// pinctrl-names = "default";
// pinctrl-0 = <&usbc0_int>;
// vbus-supply = <&vbus5v0_typec>;
// status = "okay";
//
// ports {
// #address-cells = <1>;
// #size-cells = <0>;
//
// port@0 {
// reg = <0>;
// usbc0_role_sw: endpoint@0 {
// remote-endpoint = <&dwc3_0_role_switch>;
// };
// };
// };
//
// usb_con: connector {
// compatible = "usb-c-connector";
// label = "USB-C";
// data-role = "dual";
// power-role = "dual";
// try-power-role = "sink";
// op-sink-microwatt = <1000000>;
// sink-pdos =
// <PDO_FIXED(5000, 1000, PDO_FIXED_USB_COMM)>;
// source-pdos =
// <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
//
// altmodes {
// #address-cells = <1>;
// #size-cells = <0>;
//
// altmode@0 {
// reg = <0>;
// svid = <0xff01>;
// vdo = <0xffffffff>;
// };
// };
//
// ports {
// #address-cells = <1>;
// #size-cells = <0>;
//
// port@0 {
// reg = <0>;
// usbc0_orien_sw: endpoint {
// remote-endpoint = <&usbdp_phy0_orientation_switch>;
// };
// };
//
// port@1 {
// reg = <1>;
// dp_altmode_mux: endpoint {
// remote-endpoint = <&usbdp_phy0_dp_altmode_mux>;
// };
// };
// };
// };
//};
hym8563: hym8563@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "hym8563";
pinctrl-names = "default";
pinctrl-0 = <&hym8563_int>;
interrupt-parent = <&gpio0>;
interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
wakeup-source;
};
};
3、拿掉LCD的RESET，配置type C0和type C1
&pinctrl {
cam {
mipicsi0_pwr: mipicsi0-pwr {
rockchip,pins =
/* camera power en */
<1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
};
mipicsi1_pwr: mipicsi1-pwr {
rockchip,pins =
/* camera power en */
<1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
};
mipidcphy0_pwr: mipidcphy0-pwr {
rockchip,pins =
/* camera power en */
<2 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
hdmi {
hdmirx_det: hdmirx-det {
rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
headphone {
hp_det: hp-det {
rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
hym8563 {
hym8563_int: hym8563-int {
rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
//lcd {
// lcd_rst_gpio: lcd-rst-gpio {
// rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
// };
//};
leds {
work_leds_gpio: work-leds-gpio {
rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
sdio-pwrseq {
wifi_enable_h: wifi-enable-h {
rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
sdmmc {
sd_s0_pwr: sd-s0-pwr {
rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
touch {
touch_gpio: touch-gpio {
rockchip,pins =
<3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>,
<3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
usb {
vcc5v0_host_en: vcc5v0-host-en {
rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
usb-typec {
usbc0_int: usbc0-int {
rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
};
typec5v_pwren0: typec5v-pwren0 {
rockchip,pins = <0 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
};
usbc1_int: usbc1-int {
rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>;
};
typec5v_pwren1: typec5v-pwren1 {
rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
wireless-bluetooth {
uart9_gpios: uart9-gpios {
rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
};
bt_reset_gpio: bt-reset-gpio {
rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
};
bt_wake_gpio: bt-wake-gpio {
rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
};
bt_irq_gpio: bt-irq-gpio {
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
wireless-wlan {
wifi_host_wake_irq: wifi-host-wake-irq {
rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
pcie {
pcie20x1_0_clkreqn_m1: pcie20x1-0-clkreqn-m1 {
rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_output_low>;
};
};
};
4、打开type C1
&u2phy0_otg {
rockchip,typec-vbus-det;
};
&u2phy1_otg {
phy-supply = <&vcc5v0_host>;
};
&u2phy2_host {
phy-supply = <&vcc5v0_host>;
};
&u2phy3_host {
phy-supply = <&vcc5v0_host>;
};
//&usbdp_phy0 {
// orientation-switch;
// svid = <0xff01>;
// sbu1-dc-gpios = <&gpio4 RK_PA0 GPIO_ACTIVE_HIGH>;
// sbu2-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
//
// port {
// #address-cells = <1>;
// #size-cells = <0>;
// usbdp_phy0_orientation_switch: endpoint@0 {
// reg = <0>;
// remote-endpoint = <&usbc0_orien_sw>;
// };
//
// usbdp_phy0_dp_altmode_mux: endpoint@1 {
// reg = <1>;
// remote-endpoint = <&dp_altmode_mux>;
// };
// };
//};
&usbdp_phy1 {
status = "okay";
orientation-switch;
rockchip,dp-lane-mux = <2 3>;
svid = <0xff01>;
sbu1-dc-gpios = <&gpio4 RK_PA1 GPIO_ACTIVE_HIGH>;
sbu2-dc-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
port {
#address-cells = <1>;
#size-cells = <0>;
usbdp_phy1_orientation_switch: endpoint@0 {
reg = <0>;
remote-endpoint = <&usbc1_orien_sw>;
};
usbdp_phy1_dp_altmode_mux: endpoint@1 {
reg = <1>;
remote-endpoint = <&dp1_altmode_mux>;
};
};
};
//&usbdrd_dwc3_0 {
// dr_mode = "otg";
// usb-role-switch;
// port {
// #address-cells = <1>;
// #size-cells = <0>;
// dwc3_0_role_switch: endpoint@0 {
// reg = <0>;
// remote-endpoint = <&usbc0_role_sw>;
// };
// };
//};
&usbhost3_0 {
status = "disabled";
};
&usbhost_dwc3_0 {
status = "disabled";
};
&usbdp_phy1_dp {
status = "okay";
};
&usbdp_phy1_u3 {
status = "okay";
};
&usbdrd3_1 {
status = "okay";
};
&usbdrd_dwc3_1 {
status = "okay";
dr_mode = "otg";
usb-role-switch;
port {
#address-cells = <1>;
#size-cells = <0>;
dwc3_1_role_switch: endpoint@0 {
reg = <0>;
remote-endpoint = <&usbc1_role_sw>;
};
};
};
&usbhost3_0 {
status = "okay";
};
&usbhost_dwc3_0 {
status = "okay";
};
&combphy2_psu {
status = "okay";
};
&work_led {
gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&work_leds_gpio>;
};
5、【插拔USB3.0接口的U盘】测试LOG：
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 44.714568] dwc3 fc400000.usb: request 0000000022457179 was not queued to ep0out
[ 44.714710] android_work: did not send uevent (0 0 0000000000000000)
[ 44.822692] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[ 44.823204] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 44.823497] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 9
[ 44.823627] xhci-hcd xhci-hcd.15.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 44.823657] xhci-hcd xhci-hcd.15.auto: irq 151, io mem 0xfc400000
[ 44.823764] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 44.823974] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 10
[ 44.823989] xhci-hcd xhci-hcd.15.auto: Host supports USB 3.0 SuperSpeed
[ 44.824089] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 44.824099] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.824108] usb usb9: Product: xHCI Host Controller
[ 44.824116] usb usb9: Manufacturer: Linux 5.10.198 xhci-hcd
[ 44.824124] usb usb9: SerialNumber: xhci-hcd.15.auto
[ 44.824515] hub 9-0:1.0: USB hub found
[ 44.824539] hub 9-0:1.0: 1 port detected
[ 44.824837] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[ 44.824908] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 44.824917] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.824926] usb usb10: Product: xHCI Host Controller
[ 44.824934] usb usb10: Manufacturer: Linux 5.10.198 xhci-hcd
[ 44.824942] usb usb10: SerialNumber: xhci-hcd.15.auto
[ 44.825608] hub 10-0:1.0: USB hub found
[ 44.825640] hub 10-0:1.0: 1 port detected
[ 44.827465] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 44.827482] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 44.827683] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 44.827714] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 44.827725] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 44.827752] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 45.362450] usb 10-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 45.392242] usb 10-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[ 45.392264] usb 10-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 45.392269] usb 10-1: Product: DataTraveler 3.0
[ 45.392274] usb 10-1: Manufacturer: Kingston
[ 45.392278] usb 10-1: SerialNumber: E0D55EA573CDF830C93D1F6C
[ 45.480758] usb-storage 10-1:1.0: USB Mass Storage device detected
[ 45.482527] scsi host1: usb-storage 10-1:1.0
[ 45.489108] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 45.489202] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 45.489506] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 45.489565] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 45.489595] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 45.489653] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 46.496813] scsi 1:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 46.500113] sd 1:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[ 46.500850] sd 1:0:0:0: [sda] Write Protect is off
[ 46.501527] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 46.506660] sda: sda1
[ 46.508319] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 46.510685] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 46.510735] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 46.510835] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 46.510858] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 46.510869] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 46.510892] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 46.625064] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 46.627223] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 010 Device 001: ID 1d6b:0003
Bus 001 Device 001: ID 1d6b:0002
Bus 010 Device 002: ID 0951:1666
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 009 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 92.983761] xhci-hcd xhci-hcd.15.auto: remove, state 1
[ 92.983805] usb usb10: USB disconnect, device number 1
[ 92.983816] usb 10-1: USB disconnect, device number 2
[ 93.085147] xhci-hcd xhci-hcd.15.auto: USB bus 10 deregistered
[ 93.085419] xhci-hcd xhci-hcd.15.auto: remove, state 4
[ 93.085437] usb usb9: USB disconnect, device number 1
[ 93.086351] xhci-hcd xhci-hcd.15.auto: USB bus 9 deregistered
[ 93.326244] android_work: did not send uevent (0 0 0000000000000000)
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 106.464861] dwc3 fc400000.usb: request 0000000021b1168c was not queued to ep0out
[ 106.464923] android_work: did not send uevent (0 0 0000000000000000)
[ 106.572317] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[ 106.572361] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 106.572819] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 9
[ 106.572973] xhci-hcd xhci-hcd.15.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 106.573007] xhci-hcd xhci-hcd.15.auto: irq 151, io mem 0xfc400000
[ 106.573132] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 106.573307] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 10
[ 106.573322] xhci-hcd xhci-hcd.15.auto: Host supports USB 3.0 SuperSpeed
[ 106.573430] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 106.573441] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 106.573449] usb usb9: Product: xHCI Host Controller
[ 106.573457] usb usb9: Manufacturer: Linux 5.10.198 xhci-hcd
[ 106.573465] usb usb9: SerialNumber: xhci-hcd.15.auto
[ 106.573869] hub 9-0:1.0: USB hub found
[ 106.573895] hub 9-0:1.0: 1 port detected
[ 106.574191] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[ 106.574263] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 106.574273] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 106.574281] usb usb10: Product: xHCI Host Controller
[ 106.574289] usb usb10: Manufacturer: Linux 5.10.198 xhci-hcd
[ 106.574298] usb usb10: SerialNumber: xhci-hcd.15.auto
[ 106.574697] hub 10-0:1.0: USB hub found
[ 106.574720] hub 10-0:1.0: 1 port detected
[ 106.576562] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 106.576574] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 106.576675] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 106.576697] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 106.576707] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 106.576732] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 107.109039] usb 10-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 107.138799] usb 10-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[ 107.138807] usb 10-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 107.138809] usb 10-1: Product: DataTraveler 3.0
[ 107.138811] usb 10-1: Manufacturer: Kingston
[ 107.138813] usb 10-1: SerialNumber: E0D55EA573CDF830C93D1F6C
[ 107.226872] usb-storage 10-1:1.0: USB Mass Storage device detected
[ 107.228276] scsi host1: usb-storage 10-1:1.0
[ 107.230656] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 107.230687] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 107.230835] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 107.230860] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 107.230871] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 107.230894] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 108.256951] scsi 1:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 108.260146] sd 1:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[ 108.260727] sd 1:0:0:0: [sda] Write Protect is off
[ 108.261318] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 108.266613] sda: sda1
[ 108.269764] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 108.271485] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 108.271510] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 108.271602] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 108.271622] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 108.271631] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 108.271652] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 108.380628] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 108.384109] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 010 Device 001: ID 1d6b:0003
Bus 001 Device 001: ID 1d6b:0002
Bus 010 Device 002: ID 0951:1666
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 009 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
6、核对GPIO口的配置：
root@rk3588-buildroot:/#
pinmux-pins-buildroot:/# cat /sys/kernel/debug/pinctrl/pinctrl-rockchip-pinctrl/p
Pinmux settings per pin
Format: pin (name): mux_owner gpio_owner hog?
pin 0 (gpio0-0): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 1 (gpio0-1): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 2 (gpio0-2): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 3 (gpio0-3): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 4 (gpio0-4): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-det
pin 5 (gpio0-5): feb20000.spi (GPIO UNCLAIMED) function spi2 group spi2m2-pins
pin 6 (gpio0-6): feb20000.spi (GPIO UNCLAIMED) function spi2 group spi2m2-pins
pin 7 (gpio0-7): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 8 (gpio0-8): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 9 (gpio0-9): feb20000.spi (GPIO UNCLAIMED) function spi2 group spi2m2-cs0
pin 10 (gpio0-10): wireless-wlan (GPIO UNCLAIMED) function wireless-wlan group wifi-host-wake-irq
pin 11 (gpio0-11): feb20000.spi (GPIO UNCLAIMED) function spi2 group spi2m2-pins
pin 12 (gpio0-12): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 13 (gpio0-13): fiq-debugger (GPIO UNCLAIMED) function uart2 group uart2m0-xfer
pin 14 (gpio0-14): fiq-debugger (GPIO UNCLAIMED) function uart2 group uart2m0-xfer
pin 15 (gpio0-15): vcc-3v3-sd-s0-regulator gpio0:15 function sdmmc group sd-s0-pwr
pin 16 (gpio0-16): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 17 (gpio0-17): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 18 (gpio0-18): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 19 (gpio0-19): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 20 (gpio0-20): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 21 (gpio0-21): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 22 (gpio0-22): febd0010.pwm (GPIO UNCLAIMED) function pwm5 group pwm5m1-pins
pin 23 (gpio0-23): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 24 (gpio0-24): vbus5v0-typec0 gpio0:24 function usb-typec group typec5v-pwren0
pin 25 (gpio0-25): fd880000.i2c (GPIO UNCLAIMED) function i2c0 group i2c0m2-xfer
pin 26 (gpio0-26): fd880000.i2c (GPIO UNCLAIMED) function i2c0 group i2c0m2-xfer
pin 27 (gpio0-27): vbus5v0-typec1 gpio0:27 function usb-typec group typec5v-pwren1
pin 28 (gpio0-28): fea90000.i2c (GPIO UNCLAIMED) function i2c1 group i2c1m2-xfer
pin 29 (gpio0-29): fea90000.i2c (GPIO UNCLAIMED) function i2c1 group i2c1m2-xfer
pin 30 (gpio0-30): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 31 (gpio0-31): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 32 (gpio1-0): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 33 (gpio1-1): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 34 (gpio1-2): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 35 (gpio1-3): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 36 (gpio1-4): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 37 (gpio1-5): fde80000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim0-tx0-hpd
pin 38 (gpio1-6): fdea0000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim0-tx1-hpd
pin 39 (gpio1-7): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 40 (gpio1-8): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 41 (gpio1-9): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 42 (gpio1-10): vcc-mipidcphy0-regulator gpio1:42 function cam group mipidphy0-pwr
pin 43 (gpio1-11): 5-0022 (GPIO UNCLAIMED) function usb-typec group usbc1-int
pin 44 (gpio1-12): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 45 (gpio1-13): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 46 (gpio1-14): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 47 (gpio1-15): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 48 (gpio1-16): feab0000.i2c (GPIO UNCLAIMED) function i2c3 group i2c3m0-xfer
pin 49 (gpio1-17): feab0000.i2c (GPIO UNCLAIMED) function i2c3 group i2c3m0-xfer
pin 50 (gpio1-18): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 51 (gpio1-19): fe470000.i2s (GPIO UNCLAIMED) function i2s0 group i2s0-sclk
pin 52 (gpio1-20): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 53 (gpio1-21): fe470000.i2s (GPIO UNCLAIMED) function i2s0 group i2s0-lrck
pin 54 (gpio1-22): (MUX UNCLAIMED) gpio1:54
pin 55 (gpio1-23): fe470000.i2s (GPIO UNCLAIMED) function i2s0 group i2s0-sdo0
pin 56 (gpio1-24): fec90000.i2c (GPIO UNCLAIMED) function i2c7 group i2c7m0-xfer
pin 57 (gpio1-25): fec90000.i2c (GPIO UNCLAIMED) function i2c7 group i2c7m0-xfer
pin 58 (gpio1-26): vcc-mipicsi0-regulator gpio1:58 function cam group mipicsi0-pwr
pin 59 (gpio1-27): vcc-mipicsi1-regulator gpio1:59 function cam group mipicsi1-pwr
pin 60 (gpio1-28): fe470000.i2s (GPIO UNCLAIMED) function i2s0 group i2s0-sdi0
pin 61 (gpio1-29): fdee0000.hdmirx-controller gpio1:61 function hdmi group hdmirx-det
pin 62 (gpio1-30): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 63 (gpio1-31): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 64 (gpio2-0): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 65 (gpio2-1): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 66 (gpio2-2): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 67 (gpio2-3): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 68 (gpio2-4): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 69 (gpio2-5): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 70 (gpio2-6): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 71 (gpio2-7): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 72 (gpio2-8): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 73 (gpio2-9): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 74 (gpio2-10): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 75 (gpio2-11): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 76 (gpio2-12): feac0000.i2c (GPIO UNCLAIMED) function i2c4 group i2c4m1-xfer
pin 77 (gpio2-13): feac0000.i2c (GPIO UNCLAIMED) function i2c4 group i2c4m1-xfer
pin 78 (gpio2-14): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 79 (gpio2-15): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 80 (gpio2-16): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 81 (gpio2-17): (MUX UNCLAIMED) gpio2:81
pin 82 (gpio2-18): febc0000.serial (GPIO UNCLAIMED) function uart9 group uart9m0-xfer
pin 83 (gpio2-19): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 84 (gpio2-20): febc0000.serial (GPIO UNCLAIMED) function uart9 group uart9m0-xfer
pin 85 (gpio2-21): (MUX UNCLAIMED) gpio2:85
pin 86 (gpio2-22): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 87 (gpio2-23): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 88 (gpio2-24): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 89 (gpio2-25): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 90 (gpio2-26): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 91 (gpio2-27): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 92 (gpio2-28): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 93 (gpio2-29): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 94 (gpio2-30): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 95 (gpio2-31): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 96 (gpio3-0): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rgmii-bus
pin 97 (gpio3-1): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rgmii-bus
pin 98 (gpio3-2): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rgmii-bus
pin 99 (gpio3-3): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rgmii-bus
pin 100 (gpio3-4): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rgmii-clk
pin 101 (gpio3-5): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rgmii-clk
pin 102 (gpio3-6): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 103 (gpio3-7): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rx-bus2
pin 104 (gpio3-8): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rx-bus2
pin 105 (gpio3-9): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-rx-bus2
pin 106 (gpio3-10): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 107 (gpio3-11): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-tx-bus2
pin 108 (gpio3-12): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-tx-bus2
pin 109 (gpio3-13): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-tx-bus2
pin 110 (gpio3-14): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 111 (gpio3-15): (MUX UNCLAIMED) gpio3:111
pin 112 (gpio3-16): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 113 (gpio3-17): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 114 (gpio3-18): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-miim
pin 115 (gpio3-19): fe1c0000.ethernet (GPIO UNCLAIMED) function gmac1 group gmac1-miim
pin 116 (gpio3-20): fdea0000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim2-tx1-cec
pin 117 (gpio3-21): fdea0000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim1-tx1-sda
pin 118 (gpio3-22): fdea0000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim1-tx1-scl
pin 119 (gpio3-23): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 120 (gpio3-24): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 121 (gpio3-25): fdee0000.hdmirx-controller (GPIO UNCLAIMED) function hdmi group hdmim1-rx
pin 122 (gpio3-26): fdee0000.hdmirx-controller (GPIO UNCLAIMED) function hdmi group hdmim1-rx
pin 123 (gpio3-27): fdee0000.hdmirx-controller (GPIO UNCLAIMED) function hdmi group hdmim1-rx
pin 124 (gpio3-28): fdee0000.hdmirx-controller (GPIO UNCLAIMED) function hdmi group hdmim1-rx
pin 125 (gpio3-29): fde60000.dp (GPIO UNCLAIMED) function dp1 group dp1m0-pins
pin 126 (gpio3-30): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 127 (gpio3-31): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 128 (gpio4-0): (MUX UNCLAIMED) gpio4:128
pin 129 (gpio4-1): (MUX UNCLAIMED) gpio4:129
pin 130 (gpio4-2): (MUX UNCLAIMED) gpio4:130
pin 131 (gpio4-3): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 132 (gpio4-4): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 133 (gpio4-5): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 134 (gpio4-6): fead0000.i2c (GPIO UNCLAIMED) function i2c5 group i2c5m2-xfer
pin 135 (gpio4-7): fead0000.i2c (GPIO UNCLAIMED) function i2c5 group i2c5m2-xfer
pin 136 (gpio4-8): vcc5v0-host gpio4:136 function usb group vcc5v0-host-en
pin 137 (gpio4-9): (MUX UNCLAIMED) gpio4:137
pin 138 (gpio4-10): (MUX UNCLAIMED) gpio4:138
pin 139 (gpio4-11): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 140 (gpio4-12): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 141 (gpio4-13): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 142 (gpio4-14): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 143 (gpio4-15): fde80000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim0-tx0-scl
pin 144 (gpio4-16): fde80000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim0-tx0-sda
pin 145 (gpio4-17): fde80000.hdmi (GPIO UNCLAIMED) function hdmi group hdmim0-tx0-cec
pin 146 (gpio4-18): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 147 (gpio4-19): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 148 (gpio4-20): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 149 (gpio4-21): febc0000.serial (GPIO UNCLAIMED) function uart9 group uart9m0-ctsn
pin 150 (gpio4-22): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 151 (gpio4-23): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 152 (gpio4-24): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-bus4
pin 153 (gpio4-25): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-bus4
pin 154 (gpio4-26): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-bus4
pin 155 (gpio4-27): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-bus4
pin 156 (gpio4-28): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-cmd
pin 157 (gpio4-29): fe2c0000.mmc (GPIO UNCLAIMED) function sdmmc group sdmmc-clk
pin 158 (gpio4-30): (MUX UNCLAIMED) (GPIO UNCLAIMED)
pin 159 (gpio4-31): (MUX UNCLAIMED) (GPIO UNCLAIMED)
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# cat /sys/kernel/debug/gpio
gpiochip0: GPIOs 0-31, parent: platform/fd8a0000.gpio, gpio0:
gpio-15 ( |vcc-3v3-sd-s0-regula) out lo
gpio-24 ( |vbus5v0-typec0 ) out lo
gpio-27 ( |vbus5v0-typec1 ) out hi
gpiochip1: GPIOs 32-63, parent: platform/fec20000.gpio, gpio1:
gpio-42 ( |vcc-mipidcphy0-regul) out lo
gpio-54 ( |work ) out lo
gpio-58 ( |vcc-mipicsi0-regulat) out lo
gpio-59 ( |vcc-mipicsi1-regulat) out lo
gpio-61 ( |hdmirx-det ) in hi ACTIVE LOW
gpiochip2: GPIOs 64-95, parent: platform/fec30000.gpio, gpio2:
gpio-81 ( |vcc3v3-lcd0-n ) out lo
gpio-85 ( |vcc3v3-pcie30 ) out lo
gpiochip3: GPIOs 96-127, parent: platform/fec40000.gpio, gpio3:
gpio-111 ( |snps,reset ) out hi ACTIVE LOW
gpiochip4: GPIOs 128-159, parent: platform/fec50000.gpio, gpio4:
gpio-128 ( |ircut-open ) out lo
gpio-129 ( |sbu1-dc ) out lo
gpio-130 ( |sbu2-dc ) out hi
gpio-136 ( |vcc5v0-host ) out hi
gpio-137 ( |enable ) out hi
gpio-138 ( |enable ) out hi
gpiochip5: GPIOs 509-511, parent: platform/rk806-pinctrl.2.auto, rk806-gpio, can sleep:
root@rk3588-buildroot:/#
7、
【插拔USB3.0接口的U盘】完整的LOG：
[BEGIN] 2025/12/15 21:02:37
DDR d5483af87d cym 23/11/23-16:15:24,fwver: v1.15
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
Manufacturer ID:0x13
CH0 RX Vref:30.1%, TX Vref:24.8%,0.0%
CH1 RX Vref:28.5%, TX Vref:23.8%,0.0%
CH2 RX Vref:31.8%, TX Vref:22.8%,0.0%
CH3 RX Vref:29.7%, TX Vref:22.8%,0.0%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13
unknown raw ID 0 0 0
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(2e8446f969...) + OK
## Checking uboot 0x00200000 ... sha256(fcf10633af...) + OK
## Checking fdt 0x00345490 ... sha256(a434b1c4fe...) + OK
## Checking atf-2 0xff100000 ... sha256(9f75e6ec37...) + OK
## Checking atf-3 0x000f0000 ... sha256(c80587de50...) + OK
## Checking optee 0x08400000 ... sha256(4b2d406bfc...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 79.446/211.305 ms
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-662-g4acbe711b-dirty:finley.xiao, fwver: v1.44
NOTICE: BL31: Built : 16:44:24, Nov 7 2023
INFO: spec: 0x1
INFO: code: 0x88
INFO: ext 32k is not valid
INFO: ddr: stride-en 4CH
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
INFO: l3 cache partition cfg-0
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-752-g62aa10b78 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Sep 25 10:04:34 CST 2023 aarch64, fwver: v1.15
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09 (Dec 15 2025 - 20:27:43 +0800)
Model: Rockchip RK3588 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfeb50000
DRAM: 4 GiB
Sysmem: init
Relocation Offset: eda18000
Relocation fdt: eb9fa160 - eb9fecd0
CR: M/C/I
Using default environment
optee api revision: 2.0
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS400 Enhanced Strobe, 200Mhz
PartType: EFI
TEEC: Waring: Could not find security partition
DM: v2
boot mode: None
RESC: 'boot', blk@0x00019b95
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found!
en-gpios- not found!
vdd_cpu_big1_s0 800000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found!
en-gpios- not found!
vdd_npu_s0 800000 uV
spi2: RK806: 2
ON=0x40, OFF=0x00
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000'
Device 'gpio@fec20000': seq 1 is in use by 'gpio@fd8a0000'
serdes_power_init failed to get serdes misc device
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: Rockchip RK3588 EVB7 V11 Board
MPIDR: 0x81000000
Minidump: init...
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
Using display timing dts
dsi@fde20000: detailed mode clock 45000 kHz, flags[a]
H: 1024 1064 1112 1160
V: 0600 0640 0644 0692
bus_format: 100e
VOP update mode to: 1024x600p56, type: MIPI0 for VP3
VP3 set crtc_clock to 44118KHz
VOP VP3 enable Esmart3[654x270->654x270@185x165] fmt[2] addr[0xedf04000]
final DSI-Link bandwidth: 294120 Kbps x 4
hdmi@fde80000 disconnected
i2c read err!
i2c read err!
i2c read err!
i2c read err!
i2c read err!
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1920x1080 bus_format:0x100a
hdmi@fdea0000: detailed mode clock 148500 kHz, flags[5]
H: 1920 2008 2052 2200
V: 1080 1084 1089 1125
bus_format: 100a
VOP update mode to: 1920x1080p60, type: HDMI1 for VP1
dclk:148500,if_pixclk_div;2,if_dclk_div:4
VP1 set crtc_clock to 148500KHz
VOP VP1 enable Esmart1[654x270->654x270@633x405] fmt[2] addr[0xedf04000]
CEA mode used vic=16
mtmdsclock:148500000
hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
hdptx phy pll locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
bus_width:0x16a8c8,bit_rate:1485000
hdptx phy lane locked!
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
b0pll 24000 KHz
b1pll 24000 KHz
lpll 24000 KHz
v0pll 24000 KHz
aupll 786431 KHz
cpll 1500000 KHz
gpll 1188000 KHz
npll 850000 KHz
ppll 1100000 KHz
aclk_center_root 702000 KHz
pclk_center_root 100000 KHz
hclk_center_root 396000 KHz
aclk_center_low_root 500000 KHz
aclk_top_root 750000 KHz
pclk_top_root 100000 KHz
aclk_low_top_root 396000 KHz
Net: Device 'gpio@fec40000': seq 3 is in use by 'gpio@fec20000'
eth1: ethernet@fe1c0000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "(none)"
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe9486740 with size 0x02372a00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e9486740 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
Description: unavailable
Type: Kernel Image
Compression: uncompressed
Data Start: 0xe94cc740
Data Size: 36882944 Bytes = 35.2 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x00400000
Entry Point: 0x00400000
Hash algo: sha256
Hash value: f27dc12c05a08b3be36c82af97205fe3b85da864e272bf91dfb898f74e2e87ec
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e9486740 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
Description: unavailable
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0xe9486f40
Data Size: 284380 Bytes = 277.7 KiB
Architecture: AArch64
Load Address: 0x08300000
Hash algo: sha256
Hash value: 8b5b179b34e5989fba98bce6a107efa91a9d067e34343ed4ec8ea2eb039fc635
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x08300000 to 0x08300000
Booting using the fdt blob at 0x08300000
Loading Kernel Image from 0xe94cc740 to 0x00400000 ... OK
kernel loaded at 0x00400000, end = 0x0272ca00
Using Device Tree in place at 0000000008300000, end 00000000083486db
WARNING: could not set reg FDT_ERR_BADOFFSET.
## reserved-memory:
cma: addr=10000000 size=8000000
drm-logo@00000000: addr=edf00000 size=b8000
ramoops@110000: addr=110000 size=e0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
Total: 731.646/1030.333 ms
Starting kernel ...
[ 1.035318] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 1.035336] Linux version 5.10.198 (jinhualong@jinhualong-LEGION-REN7000K-26IRX) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #2 SMP Mon Dec 15 16:00:23 CST 2025
[ 1.038942] random: crng init done
[ 1.046999] Machine model: Rockchip RK3588 EVB7 V11 Board
[ 1.083698] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[ 1.088333] printk: bootconsole [uart8250] enabled
[ 1.091155] efi: UEFI not found.
[ 1.097174] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[ 1.098332] Reserved memory: created CMA memory pool at 0x0000000010000000, size 128 MiB
[ 1.099073] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[ 1.169983] Zone ranges:
[ 1.170223] DMA [mem 0x0000000000200000-0x00000000ffffffff]
[ 1.170793] DMA32 empty
[ 1.171059] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.171626] Movable zone start for each node
[ 1.172016] Early memory node ranges
[ 1.172346] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 1.172920] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 1.173495] node 0: [mem 0x00000001f0000000-0x00000001ffffffff]
[ 1.174070] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ 1.198557] psci: probing for conduit method from DT.
[ 1.199027] psci: PSCIv1.1 detected in firmware.
[ 1.199451] psci: Using standard PSCI v0.2 function IDs
[ 1.199932] psci: Trusted OS migration not required
[ 1.200381] psci: SMC Calling Convention v1.2
[ 1.201138] percpu: Embedded 30 pages/cpu s83800 r8192 d30888 u122880
[ 1.201901] Detected VIPT I-cache on CPU0
[ 1.202301] CPU features: detected: GIC system register CPU interface
[ 1.202890] CPU features: detected: Virtualization Host Extensions
[ 1.203460] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 1.204110] alternatives: patching kernel code
[ 1.206068] Built 1 zonelists, mobility grouping on. Total pages: 1027656
[ 1.206703] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTUUID=614e0000-0000 rcupdate.rcu_expedited=1 rcu_nocbs=all androidboot.fwver=ddr-v1.15-d5483af87d,spl-v1.13,bl31-v1.44,bl32-v1.15,uboot-12/15/2025
[ 1.210401] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 1.211323] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 1.212033] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 1.218801] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[ 1.249816] Memory: 3859084K/4175872K available (18752K kernel code, 3506K rwdata, 6916K rodata, 6720K init, 590K bss, 185716K reserved, 131072K cma-reserved)
[ 1.251217] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 1.251840] ftrace: allocating 57356 entries in 225 pages
[ 1.323204] ftrace: allocated 225 pages with 4 groups
[ 1.323883] rcu: Hierarchical RCU implementation.
[ 1.324318] rcu: RCU event tracing is enabled.
[ 1.324733] rcu: RCU dyntick-idle grace-period acceleration is enabled.
[ 1.325346] All grace periods are expedited (rcu_expedited).
[ 1.325872] Rude variant of Tasks RCU enabled.
[ 1.326288] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 1.330771] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 1.333772] GICv3: GIC: Using split EOI/Deactivate mode
[ 1.334255] GICv3: 480 SPIs implemented
[ 1.334606] GICv3: 0 Extended SPIs implemented
[ 1.335034] GICv3: Distributor has no Range Selector support
[ 1.335557] GICv3: 16 PPIs implemented
[ 1.335941] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[ 1.336655] ITS [mem 0xfe640000-0xfe65ffff]
[ 1.337082] ITS@0x00000000fe640000: allocated 8192 Devices @1f01f0000 (indirect, esz 8, psz 64K, shr 0)
[ 1.337961] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @1f0200000 (flat, esz 2, psz 64K, shr 0)
[ 1.338910] ITS: using cache flushing for cmd queue
[ 1.339380] ITS [mem 0xfe660000-0xfe67ffff]
[ 1.339801] ITS@0x00000000fe660000: allocated 8192 Devices @1f0220000 (indirect, esz 8, psz 64K, shr 0)
[ 1.340677] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @1f0230000 (flat, esz 2, psz 64K, shr 0)
[ 1.341625] ITS: using cache flushing for cmd queue
[ 1.342290] GICv3: using LPI property table @0x00000001f0240000
[ 1.342950] GIC: using cache flushing for LPI property table
[ 1.343473] GICv3: CPU0: using allocated LPI pending table @0x00000001f0250000
[ 1.344175] rcu: Offload RCU callbacks from CPUs: 0-7.
[ 1.453282] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 1.453829] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 1.454792] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 1.456708] Console: colour dummy device 80x25
[ 1.457131] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 1.458049] pid_max: default: 32768 minimum: 301
[ 1.458547] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.459212] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 1.461079] rcu: Hierarchical SRCU implementation.
[ 1.462220] Platform MSI: msi-controller@fe640000 domain created
[ 1.462765] Platform MSI: msi-controller@fe660000 domain created
[ 1.463644] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[ 1.464392] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[ 1.465314] EFI services will not be available.
[ 1.465956] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[ 1.467460] Detected VIPT I-cache on CPU1
[ 1.467483] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[ 1.467498] GICv3: CPU1: using allocated LPI pending table @0x00000001f0260000
[ 1.467537] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[ 1.468692] Detected VIPT I-cache on CPU2
[ 1.468712] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[ 1.468726] GICv3: CPU2: using allocated LPI pending table @0x00000001f0270000
[ 1.468761] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[ 1.469892] Detected VIPT I-cache on CPU3
[ 1.469909] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[ 1.469922] GICv3: CPU3: using allocated LPI pending table @0x00000001f0280000
[ 1.469954] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[ 1.471135] CPU features: detected: Spectre-v4
[ 1.471137] CPU features: detected: Spectre-BHB
[ 1.471139] Detected PIPT I-cache on CPU4
[ 1.471151] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[ 1.471158] GICv3: CPU4: using allocated LPI pending table @0x00000001f0290000
[ 1.471180] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[ 1.472277] Detected PIPT I-cache on CPU5
[ 1.472289] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[ 1.472297] GICv3: CPU5: using allocated LPI pending table @0x00000001f02a0000
[ 1.472318] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[ 1.473410] Detected PIPT I-cache on CPU6
[ 1.473421] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[ 1.473429] GICv3: CPU6: using allocated LPI pending table @0x00000001f02b0000
[ 1.473451] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[ 1.474560] Detected PIPT I-cache on CPU7
[ 1.474571] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[ 1.474579] GICv3: CPU7: using allocated LPI pending table @0x00000001f02c0000
[ 1.474601] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[ 1.474651] smp: Brought up 1 node, 8 CPUs
[ 1.491191] SMP: Total of 8 processors activated.
[ 1.491617] CPU features: detected: Privileged Access Never
[ 1.492112] CPU features: detected: LSE atomic instructions
[ 1.492607] CPU features: detected: User Access Override
[ 1.493077] CPU features: detected: 32-bit EL0 Support
[ 1.493533] CPU features: detected: Common not Private translations
[ 1.494089] CPU features: detected: RAS Extension Support
[ 1.494568] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 1.495338] CPU features: detected: CRC32 instructions
[ 1.495794] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 1.496412] CPU features: detected: RCpc load-acquire (LDAPR)
[ 1.521398] CPU: All CPU(s) started at EL2
[ 1.522958] devtmpfs: initialized
[ 1.533247] Registered cp15_barrier emulation handler
[ 1.533701] Registered setend emulation handler
[ 1.534160] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 1.535034] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[ 1.536570] pinctrl core: initialized pinctrl subsystem
[ 1.537204] DMI not present or invalid.
[ 1.537629] NET: Registered protocol family 16
[ 1.538587] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[ 1.539260] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 1.540326] Registered FIQ tty driver
[ 1.540743] thermal_sys: Registered thermal governor 'fair_share'
[ 1.540745] thermal_sys: Registered thermal governor 'step_wise'
[ 1.541285] thermal_sys: Registered thermal governor 'user_space'
[ 1.541818] thermal_sys: Registered thermal governor 'power_allocator'
[ 1.542467] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 1.543768] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[ 1.544493] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[ 1.545220] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[ 1.545944] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[ 1.546667] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[ 1.547386] cpuidle: using governor menu
[ 1.547810] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 1.548492] ASID allocator initialised with 65536 entries
[ 1.550130] ramoops: dmesg-0 0x18000@0x0000000000110000
[ 1.550592] ramoops: dmesg-1 0x18000@0x0000000000128000
[ 1.551063] ramoops: console 0x80000@0x0000000000140000
[ 1.551530] ramoops: pmsg 0x30000@0x00000000001c0000
[ 1.552183] printk: console [ramoops-1] enabled
[ 1.552588] pstore: Registered ramoops as persistent store backend
[ 1.553138] ramoops: using 0xe0000@0x110000, ecc: 0
[ 1.587238] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[ 1.587970] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[ 1.588666] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[ 1.589379] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[ 1.590096] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[ 1.590704] rockchip-pinctrl pinctrl: probed pinctrl
[ 1.602307] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ 1.602803] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 1.603314] fiq_debugger_probe: could not install nmi irq handler
[[ 1.603889] printk: console [ttyFIQ0] enabled
1.603889] printk: console [ttyFIQ0] enabled
[ 1.604655] printk: bootconsole [uart8250] disabled
[ 1.604655] printk: bootconsole [uart8250] disabled
[ 1.605132] Registered fiq debugger ttyFIQ0
[ 1.605338] vcc5v0_sys: supplied by vcc12v_dcin
[ 1.605414] vcc5v0_usbdcin: supplied by vcc12v_dcin
[ 1.605486] vcc5v0_usb: supplied by vcc5v0_usbdcin
[ 1.605557] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[ 1.605689] vbus5v0_typec0: supplied by vcc5v0_sys
[ 1.605787] vbus5v0_typec1: supplied by vcc5v0_sys
[ 1.605858] vcc3v3_pcie30: supplied by vcc12v_dcin
[ 1.605986] vcc5v0_host: supplied by vcc5v0_usb
[ 1.606573] iommu: Default domain type: Translated
[ 1.608915] SCSI subsystem initialized
[ 1.608970] usbcore: registered new interface driver usbfs
[ 1.608981] usbcore: registered new interface driver hub
[ 1.608992] usbcore: registered new device driver usb
[ 1.609018] mc: Linux media interface: v0.10
[ 1.609025] videodev: Linux video capture interface: v2.00
[ 1.609045] pps_core: LinuxPPS API ver. 1 registered
[ 1.609048] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.609053] PTP clock support registered
[ 1.609065] EDAC MC: Ver: 3.0.0
[ 1.609297] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 1.609324] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 1.610152] Advanced Linux Sound Architecture Driver Initialized.
[ 1.610282] Bluetooth: Core ver 2.22
[ 1.610291] NET: Registered protocol family 31
[ 1.610294] Bluetooth: HCI device and connection manager initialized
[ 1.610298] Bluetooth: HCI socket layer initialized
[ 1.610301] Bluetooth: L2CAP socket layer initialized
[ 1.610306] Bluetooth: SCO socket layer initialized
[ 1.611536] rockchip-cpuinfo cpuinfo: SoC : 35881000
[ 1.611541] rockchip-cpuinfo cpuinfo: Serial : e2d90c92c48bbc30
[ 1.611745] clocksource: Switched to clocksource arch_sys_counter
[ 1.856282] NET: Registered protocol family 2
[ 1.856354] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 1.857427] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 1.857465] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 1.857632] TCP bind hash table entries: 32768 (order: 7, 524288 bytes, linear)
[ 1.857958] TCP: Hash tables configured (established 32768 bind 32768)
[ 1.857992] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 1.858055] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear)
[ 1.858152] NET: Registered protocol family 1
[ 1.858362] RPC: Registered named UNIX socket transport module.
[ 1.858366] RPC: Registered udp transport module.
[ 1.858368] RPC: Registered tcp transport module.
[ 1.858371] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.858679] PCI: CLS 0 bytes, default 64
[ 1.859397] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property
[ 1.859790] rockchip-thermal fec00000.tsadc: tsadc is probed successfully!
[ 1.860348] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 1.862269] Initialise system trusted keyrings
[ 1.862333] workingset: timestamp_bits=62 max_order=20 bucket_order=0
[ 1.863559] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.863738] NFS: Registering the id_resolver key type
[ 1.863745] Key type id_resolver registered
[ 1.863748] Key type id_legacy registered
[ 1.863760] ntfs: driver 2.1.32 [Flags: R/O].
[ 1.863813] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.863893] fuse: init (API version 7.32)
[ 1.863966] SGI XFS with security attributes, no debug enabled
[ 1.884253] NET: Registered protocol family 38
[ 1.884258] Key type asymmetric registered
[ 1.884262] Asymmetric key parser 'x509' registered
[ 1.884273] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 1.884276] io scheduler mq-deadline registered
[ 1.884279] io scheduler kyber registered
[ 1.884625] rockchip-csi2-dphy-hw fedc0000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
[ 1.884680] rockchip-csi2-dphy-hw fedc8000.csi2-dphy1-hw: csi2 dphy hw probe successfully!
[ 1.890933] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[ 1.891487] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[ 1.893734] rk-pcie fe150000.pcie: invalid prsnt-gpios property in node
[ 1.893923] rk-pcie fe170000.pcie: invalid prsnt-gpios property in node
[ 1.893949] rk-pcie fe170000.pcie: no vpcie3v3 regulator found
[ 1.893978] pwm-backlight backlight: supply power not found, using dummy regulator
[ 1.894240] iep: Module initialized.
[ 1.894263] mpp_service mpp-srv: unknown mpp version for missing VCS info
[ 1.894266] mpp_service mpp-srv: probe start
[ 1.894299] rk-pcie fe170000.pcie: IRQ msi not found
[ 1.894309] rk-pcie fe170000.pcie: use outband MSI support
[ 1.894317] rk-pcie fe170000.pcie: Missing *config* reg space
[ 1.894330] rk-pcie fe170000.pcie: host bridge /pcie@fe170000 ranges:
[ 1.894350] rk-pcie fe170000.pcie: err 0x00f2000000..0x00f20fffff -> 0x00f2000000
[ 1.894365] rk-pcie fe170000.pcie: IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[ 1.894380] rk-pcie fe170000.pcie: MEM 0x00f2200000..0x00f2ffffff -> 0x00f2200000
[ 1.894392] rk-pcie fe170000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[ 1.894416] rk-pcie fe170000.pcie: Missing *config* reg space
[ 1.894440] rk-pcie fe170000.pcie: invalid resource
[ 1.895266] mpp_vdpu1 fdb51000.avsd-plus: Adding to iommu group 1
[ 1.895426] mpp_vdpu1 fdb51000.avsd-plus: probe device
[ 1.895502] mpp_vdpu1 fdb51000.avsd-plus: reset_group->rw_sem_on=0
[ 1.895507] mpp_vdpu1 fdb51000.avsd-plus: reset_group->rw_sem_on=0
[ 1.895608] mpp_vdpu1 fdb51000.avsd-plus: probing finish
[ 1.895840] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[ 1.895869] mpp_vdpu2 fdb50400.vdpu: probe device
[ 1.895926] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[ 1.895930] mpp_vdpu2 fdb50400.vdpu: reset_group->rw_sem_on=0
[ 1.896004] mpp_vdpu2 fdb50400.vdpu: probing finish
[ 1.896116] mpp_vepu2 jpege-ccu: probing start
[ 1.896120] mpp_vepu2 jpege-ccu: probing finish
[ 1.896194] mpp_vepu2 fdb50000.vepu: Adding to iommu group 1
[ 1.896221] mpp_vepu2 fdb50000.vepu: probing start
[ 1.896278] mpp_vepu2 fdb50000.vepu: reset_group->rw_sem_on=0
[ 1.896282] mpp_vepu2 fdb50000.vepu: reset_group->rw_sem_on=0
[ 1.896359] mpp_vepu2 fdb50000.vepu: probing finish
[ 1.896414] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[ 1.896472] mpp_vepu2 fdba0000.jpege-core: probing start
[ 1.896542] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[ 1.896622] mpp_vepu2 fdba0000.jpege-core: probing finish
[ 1.896659] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[ 1.896728] mpp_vepu2 fdba4000.jpege-core: probing start
[ 1.896794] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[ 1.896868] mpp_vepu2 fdba4000.jpege-core: probing finish
[ 1.896905] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[ 1.896974] mpp_vepu2 fdba8000.jpege-core: probing start
[ 1.897039] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[ 1.897113] mpp_vepu2 fdba8000.jpege-core: probing finish
[ 1.897159] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[ 1.897226] mpp_vepu2 fdbac000.jpege-core: probing start
[ 1.897291] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[ 1.897365] mpp_vepu2 fdbac000.jpege-core: probing finish
[ 1.897542] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[ 1.897613] mpp-iep2 fdbb0000.iep: probe device
[ 1.897695] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[ 1.897771] mpp-iep2 fdbb0000.iep: probing finish
[ 1.897901] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[ 1.898024] mpp_jpgdec fdb90000.jpegd: probe device
[ 1.898175] mpp_jpgdec fdb90000.jpegd: probing finish
[ 1.898438] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[ 1.898479] mpp_rkvdec2 fdc30000.rkvdec-ccu: ccu-mode: 1
[ 1.898482] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[ 1.898548] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[ 1.898724] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start
[ 1.898803] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found!
[ 1.898807] rkvdec2_init:1022: No niu aclk reset resource define
[ 1.898810] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found!
[ 1.898813] rkvdec2_init:1025: No niu hclk reset resource define
[ 1.898828] mpp_rkvdec2 fdc38100.rkvdec-core: no regulator, devfreq is disabled
[ 1.898872] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001
[ 1.898875] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0
[ 1.899012] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000ff001000
[ 1.899016] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x00000000fff00000
[ 1.899019] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 491520
[ 1.899022] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576
[ 1.899026] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512
[ 1.899030] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_info_count 20
[ 1.899033] mpp_rkvdec2 fdc38100.rkvdec-core: [136, 24576]
[ 1.899036] mpp_rkvdec2 fdc38100.rkvdec-core: [137, 49152]
[ 1.899039] mpp_rkvdec2 fdc38100.rkvdec-core: [141, 90112]
[ 1.899042] mpp_rkvdec2 fdc38100.rkvdec-core: [140, 49152]
[ 1.899045] mpp_rkvdec2 fdc38100.rkvdec-core: [139, 180224]
[ 1.899048] mpp_rkvdec2 fdc38100.rkvdec-core: [133, 49152]
[ 1.899051] mpp_rkvdec2 fdc38100.rkvdec-core: [134, 8192]
[ 1.899054] mpp_rkvdec2 fdc38100.rkvdec-core: [135, 4352]
[ 1.899057] mpp_rkvdec2 fdc38100.rkvdec-core: [138, 13056]
[ 1.899060] mpp_rkvdec2 fdc38100.rkvdec-core: [142, 291584]
[ 1.899081] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish
[ 1.899133] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13
[ 1.910113] rk-pcie fe150000.pcie: IRQ msi not found
[ 1.910117] rk-pcie fe150000.pcie: use outband MSI support
[ 1.910120] rk-pcie fe150000.pcie: Missing *config* reg space
[ 1.910126] rk-pcie fe150000.pcie: host bridge /pcie@fe150000 ranges:
[ 1.910135] rk-pcie fe150000.pcie: err 0x00f0000000..0x00f00fffff -> 0x00f0000000
[ 1.910141] rk-pcie fe150000.pcie: IO 0x00f0100000..0x00f01fffff -> 0x00f0100000
[ 1.910147] rk-pcie fe150000.pcie: MEM 0x00f0200000..0x00f0ffffff -> 0x00f0200000
[ 1.910151] rk-pcie fe150000.pcie: MEM 0x0900000000..0x093fffffff -> 0x0900000000
[ 1.910174] rk-pcie fe150000.pcie: Missing *config* reg space
[ 1.910192] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start
[ 1.910194] rk-pcie fe150000.pcie: invalid resource
[ 1.910272] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found!
[ 1.910275] rkvdec2_init:1022: No niu aclk reset resource define
[ 1.910279] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found!
[ 1.910281] rkvdec2_init:1025: No niu hclk reset resource define
[ 1.910294] mpp_rkvdec2 fdc48100.rkvdec-core: no regulator, devfreq is disabled
[ 1.910325] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[ 1.910340] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[ 1.910492] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000ff079000
[ 1.910495] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x00000000ffe00000
[ 1.910498] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 487424
[ 1.910501] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[ 1.910505] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[ 1.910508] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_info_count 20
[ 1.910512] mpp_rkvdec2 fdc48100.rkvdec-core: [136, 24576]
[ 1.910515] mpp_rkvdec2 fdc48100.rkvdec-core: [137, 49152]
[ 1.910518] mpp_rkvdec2 fdc48100.rkvdec-core: [141, 90112]
[ 1.910520] mpp_rkvdec2 fdc48100.rkvdec-core: [140, 49152]
[ 1.910523] mpp_rkvdec2 fdc48100.rkvdec-core: [139, 180224]
[ 1.910527] mpp_rkvdec2 fdc48100.rkvdec-core: [133, 49152]
[ 1.910529] mpp_rkvdec2 fdc48100.rkvdec-core: [134, 8192]
[ 1.910532] mpp_rkvdec2 fdc48100.rkvdec-core: [135, 4352]
[ 1.910535] mpp_rkvdec2 fdc48100.rkvdec-core: [138, 13056]
[ 1.910538] mpp_rkvdec2 fdc48100.rkvdec-core: [142, 291584]
[ 1.910557] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[ 1.910718] mpp_rkvenc2 rkvenc-ccu: probing start
[ 1.910722] mpp_rkvenc2 rkvenc-ccu: probing finish
[ 1.911121] mpp_av1dec: Adding child /av1d@fdc70000
[ 1.911285] mpp_av1dec: register device av1d-master
[ 1.911298] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[ 1.911310] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[ 1.911316] mpp_av1dec av1d-master: Adding to iommu group 17
[ 1.911469] mpp_av1dec av1d-master: probing start
[ 1.911631] mpp_av1dec av1d-master: probing finish
[ 1.911651] mpp_service mpp-srv: probe success
[ 1.918779] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.918785] dma-pl330 fea10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.919329] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.919334] dma-pl330 fea30000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.919887] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.919892] dma-pl330 fed10000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[ 1.920355] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[ 1.920396] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[ 1.920431] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[ 1.920464] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[ 1.920496] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[ 1.920898] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[ 1.921479] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 1.921852] febc0000.serial: ttyS9 at MMIO 0xfebc0000 (irq = 105, base_baud = 1500000) is a 16550A
[ 1.923367] rockchip-vop2 fdd90000.vop: Adding to iommu group 16
[ 1.930192] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 1.930201] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 1.930208] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 1.930214] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 1.930382] [drm] failed to init overlay plane Cluster0-win1
[ 1.930406] [drm] failed to init overlay plane Cluster1-win1
[ 1.930429] [drm] failed to init overlay plane Cluster2-win1
[ 1.930451] [drm] failed to init overlay plane Cluster3-win1
[ 1.938187] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc009360870)
[ 1.938571] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 1.938905] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc00936f400)
[ 1.939291] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 1.939616] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc00936f400)
[ 1.939652] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_bind] *ERROR* Failed to find panel or bridge: -517
[ 1.944105] panel-simple-dsi fde20000.dsi.0: supply power not found, using dummy regulator
[ 1.946127] brd: module loaded
[ 1.948120] loop: module loaded
[ 1.948232] zram: Added device: zram0
[ 1.948323] lkdtm: No crash points registered, enable through debugfs
[ 1.948672] system_heap: orders[0] = 6
[ 1.948676] system_heap: orders[1] = 4
[ 1.948679] system_heap: orders[2] = 0
[ 1.949444] ahci fe210000.sata: supply ahci not found, using dummy regulator
[ 1.949487] ahci fe210000.sata: supply phy not found, using dummy regulator
[ 1.949529] ahci fe210000.sata: supply target not found, using dummy regulator
[ 1.949581] ahci fe210000.sata: forcing port_map 0x0 -> 0x1
[ 1.949599] ahci fe210000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.949605] ahci fe210000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst
[ 1.949613] ahci fe210000.sata: port 0 can do FBS, forcing FBSCP
[ 1.950039] scsi host0: ahci
[ 1.950129] ata1: SATA max UDMA/133 mmio [mem 0xfe210000-0xfe210fff] port 0x100 irq 90
[ 1.950989] rockchip-spi feb20000.spi: no high_speed pinctrl state
[ 1.952044] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[ 1.952169] rk806 spi2.0: ON: 0x40 OFF:0x0
[ 1.953611] vdd_gpu_s0: supplied by vcc5v0_sys
[ 1.954570] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[ 1.955139] vdd_log_s0: supplied by vcc5v0_sys
[ 1.955635] vdd_vdenc_s0: supplied by vcc5v0_sys
[ 1.956178] vdd_ddr_s0: supplied by vcc5v0_sys
[ 1.956491] vdd2_ddr_s3: supplied by vcc5v0_sys
[ 1.956983] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[ 1.957426] vcc_3v3_s3: supplied by vcc5v0_sys
[ 1.957844] vddq_ddr_s0: supplied by vcc5v0_sys
[ 1.958339] vcc_1v8_s3: supplied by vcc5v0_sys
[ 1.958786] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[ 1.959274] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[ 1.959706] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[ 1.960138] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[ 1.960566] vdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[ 1.961083] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[ 1.961641] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[ 1.962140] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[ 1.962633] vcc_3v3_s0: supplied by vcc5v0_sys
[ 1.963060] vccio_sd_s0: supplied by vcc5v0_sys
[ 1.963529] pldo6_s3: supplied by vcc5v0_sys
[ 1.963722] rk806 spi2.0: no sleep-setting state
[ 1.963727] rk806 spi2.0: no reset-setting pinctrl state
[ 1.963731] rk806 spi2.0: no dvs-setting pinctrl state
[ 1.964955] rockchip-spi feb20000.spi: probed, poll=0, rsd=0, cs-inactive=0, ready=0
[ 1.966234] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[ 1.966358] rk_gmac-dwmac fe1c0000.ethernet: supply phy not found, using dummy regulator
[ 1.966398] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output).
[ 1.966403] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x43).
[ 1.966407] rk_gmac-dwmac fe1c0000.ethernet: Can not read property: rx_delay.
[ 1.966411] rk_gmac-dwmac fe1c0000.ethernet: set rx_delay to 0xffffffff
[ 1.966419] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[ 1.966424] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[ 1.966429] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[ 1.966439] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[ 1.966654] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[ 1.966750] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 1.966755] rk_gmac-dwmac fe1c0000.ethernet: DWMAC4/5
[ 1.966760] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[ 1.966764] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[ 1.966767] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[ 1.966771] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[ 1.966793] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[ 1.966797] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.966801] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[ 1.966805] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[ 1.966809] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[ 2.098631] mdio_bus stmmac-1: MDIO device at address 1 is missing.
[ 2.099376] usbcore: registered new interface driver rtl8150
[ 2.099392] usbcore: registered new interface driver r8152
[ 2.099553] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.113307] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.113316] ehci-pci: EHCI PCI platform driver
[ 2.113337] ehci-platform: EHCI generic platform driver
[ 2.115525] ehci-platform fc800000.usb: EHCI Host Controller
[ 2.115577] ehci-platform fc800000.usb: new USB bus registered, assigned bus number 1
[ 2.115624] ehci-platform fc800000.usb: irq 20, io mem 0xfc800000
[ 2.116189] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.125102] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.128416] ehci-platform fc800000.usb: USB 2.0 started, EHCI 1.00
[ 2.128473] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.128479] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.128483] usb usb1: Product: EHCI Host Controller
[ 2.128487] usb usb1: Manufacturer: Linux 5.10.198 ehci_hcd
[ 2.128490] usb usb1: SerialNumber: fc800000.usb
[ 2.128632] hub 1-0:1.0: USB hub found
[ 2.128642] hub 1-0:1.0: 1 port detected
[ 2.130894] ehci-platform fc880000.usb: EHCI Host Controller
[ 2.130954] ehci-platform fc880000.usb: new USB bus registered, assigned bus number 2
[ 2.130996] ehci-platform fc880000.usb: irq 22, io mem 0xfc880000
[ 2.141749] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x1
[ 2.141755] ehci-platform fc880000.usb: USB 2.0 started, EHCI 1.00
[ 2.141798] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.141803] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.141807] usb usb2: Product: EHCI Host Controller
[ 2.141811] usb usb2: Manufacturer: Linux 5.10.198 ehci_hcd
[ 2.141814] usb usb2: SerialNumber: fc880000.usb
[ 2.141937] hub 2-0:1.0: USB hub found
[ 2.141948] hub 2-0:1.0: 1 port detected
[ 2.142217] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.142226] ohci-platform: OHCI generic platform driver
[ 2.142333] ohci-platform fc840000.usb: Generic Platform OHCI controller
[ 2.142380] ohci-platform fc840000.usb: new USB bus registered, assigned bus number 3
[ 2.142411] ohci-platform fc840000.usb: irq 21, io mem 0xfc840000
[ 2.151767] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.168415] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x1
[ 2.178434] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.195080] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.202468] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 2.202475] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.202479] usb usb3: Product: Generic Platform OHCI controller
[ 2.202483] usb usb3: Manufacturer: Linux 5.10.198 ohci_hcd
[ 2.202487] usb usb3: SerialNumber: fc840000.usb
[ 2.202608] hub 3-0:1.0: USB hub found
[ 2.202620] hub 3-0:1.0: 1 port detected
[ 2.202793] ohci-platform fc8c0000.usb: Generic Platform OHCI controller
[ 2.202841] ohci-platform fc8c0000.usb: new USB bus registered, assigned bus number 4
[ 2.202872] ohci-platform fc8c0000.usb: irq 23, io mem 0xfc8c0000
[ 2.205100] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 2.221748] rk-pcie fe150000.pcie: PCIe Linking... LTSSM is 0x0
[ 2.261409] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.262467] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[ 2.262473] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.262477] usb usb4: Product: Generic Platform OHCI controller
[ 2.262481] usb usb4: Manufacturer: Linux 5.10.198 ohci_hcd
[ 2.262484] usb usb4: SerialNumber: fc8c0000.usb
[ 2.262602] hub 4-0:1.0: USB hub found
[ 2.262612] hub 4-0:1.0: 1 port detected
[ 2.263039] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 2.263087] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5
[ 2.263166] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000802002010010
[ 2.263174] xhci-hcd xhci-hcd.5.auto: irq 149, io mem 0xfc000000
[ 2.263231] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 2.263272] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 6
[ 2.263278] xhci-hcd xhci-hcd.5.auto: Host supports USB 3.0 SuperSpeed
[ 2.263314] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.263318] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.263322] usb usb5: Product: xHCI Host Controller
[ 2.263325] usb usb5: Manufacturer: Linux 5.10.198 xhci-hcd
[ 2.263329] usb usb5: SerialNumber: xhci-hcd.5.auto
[ 2.263445] hub 5-0:1.0: USB hub found
[ 2.263456] hub 5-0:1.0: 1 port detected
[ 2.263552] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.263578] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 2.263582] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.263586] usb usb6: Product: xHCI Host Controller
[ 2.263590] usb usb6: Manufacturer: Linux 5.10.198 xhci-hcd
[ 2.263593] usb usb6: SerialNumber: xhci-hcd.5.auto
[ 2.263706] hub 6-0:1.0: USB hub found
[ 2.263716] hub 6-0:1.0: 1 port detected
[ 2.263844] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 2.263890] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 7
[ 2.263949] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 2.263966] xhci-hcd xhci-hcd.6.auto: irq 150, io mem 0xfcd00000
[ 2.264013] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[ 2.264055] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 8
[ 2.264061] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0 SuperSpeed
[ 2.264094] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 2.264098] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.264102] usb usb7: Product: xHCI Host Controller
[ 2.264105] usb usb7: Manufacturer: Linux 5.10.198 xhci-hcd
[ 2.264109] usb usb7: SerialNumber: xhci-hcd.6.auto
[ 2.264225] hub 7-0:1.0: USB hub found
[ 2.264234] hub 7-0:1.0: 1 port detected
[ 2.264327] usb usb8: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.264354] usb usb8: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 2.264358] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.264361] usb usb8: Product: xHCI Host Controller
[ 2.264365] usb usb8: Manufacturer: Linux 5.10.198 xhci-hcd
[ 2.264369] usb usb8: SerialNumber: xhci-hcd.6.auto
[ 2.264476] hub 8-0:1.0: USB hub found
[ 2.264485] hub 8-0:1.0: 1 port detected
[ 2.264602] usbcore: registered new interface driver cdc_acm
[ 2.264606] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.264708] usbcore: registered new interface driver uas
[ 2.264751] usbcore: registered new interface driver usb-storage
[ 2.264780] usbcore: registered new interface driver usbserial_generic
[ 2.264788] usbserial: USB Serial support registered for generic
[ 2.264801] usbcore: registered new interface driver cp210x
[ 2.264808] usbserial: USB Serial support registered for cp210x
[ 2.264834] usbcore: registered new interface driver ftdi_sio
[ 2.264842] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.264911] usbcore: registered new interface driver keyspan
[ 2.264918] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 2.264925] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 2.264932] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 2.264939] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 2.264954] usbcore: registered new interface driver option
[ 2.264961] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.265066] usbcore: registered new interface driver oti6858
[ 2.265081] usbserial: USB Serial support registered for oti6858
[ 2.265095] usbcore: registered new interface driver pl2303
[ 2.265102] usbserial: USB Serial support registered for pl2303
[ 2.265120] usbcore: registered new interface driver qcserial
[ 2.265127] usbserial: USB Serial support registered for Qualcomm USB modem
[ 2.265149] usbcore: registered new interface driver sierra
[ 2.265155] usbserial: USB Serial support registered for Sierra USB modem
[ 2.265502] <<-GTP-INFO->> GTP driver installing...
[ 2.265605] usbcore: registered new interface driver usbtouchscreen
[ 2.266437] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.3.auto/input/input0
[ 2.266599] i2c /dev entries driver
[ 2.269986] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[ 2.278374] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[ 2.287127] vdd_npu_s0: supplied by vcc5v0_sys
[ 2.293542] i2c i2c-4: 1 i2c clients have been registered at 0x68
[ 2.306073] rockchip-pinctrl pinctrl: pin gpio0-24 already requested by vbus5v0-typec0; cannot claim for fec80000.i2c
[ 2.306079] rockchip-pinctrl pinctrl: pin-24 (fec80000.i2c) status -22
[ 2.306084] rockchip-pinctrl pinctrl: could not request pin 24 (gpio0-24) from group i2c6m0-xfer on device rockchip-pinctrl
[ 2.306088] rk3x-i2c fec80000.i2c: Error applying setting, reverse things back
[ 2.306097] rk3x-i2c: probe of fec80000.i2c failed with error -22
[ 2.306841] ircut cam_ircut: driver version: 00.01.00
[ 2.306930] ircut cam_ircut: failed get pulse-width,use dafult value 100
[ 2.306976] ircut cam_ircut: Failed to get ircut-close-gpios
[ 2.306988] ircut cam_ircut: probe successful!
[ 2.307398] rkcifhw fdce0000.rkcif: Adding to iommu group 15
[ 2.308204] rkcifhw fdce0000.rkcif: No reserved memory region assign to CIF
[ 2.308266] rkcif rkcif-mipi-lvds2: Adding to iommu group 15
[ 2.308275] rkcif rkcif-mipi-lvds2: rkcif driver version: v00.02.00
[ 2.308317] rkcif rkcif-mipi-lvds2: attach to cif hw node
[ 2.308321] rkcif rkcif-mipi-lvds2: rkcif wait line 0
[ 2.308326] : terminal subdev does not exist
[ 2.308330] : terminal subdev does not exist
[ 2.308333] : terminal subdev does not exist
[ 2.308336] : terminal subdev does not exist
[ 2.308340] : get_remote_sensor: video pad[0] is null
[ 2.308344] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.308348] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 2.308352] : get_remote_sensor: video pad[0] is null
[ 2.308355] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.308358] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 2.308361] : get_remote_sensor: video pad[0] is null
[ 2.308364] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.308368] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 2.308371] : get_remote_sensor: video pad[0] is null
[ 2.308373] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
[ 2.308377] : rkcif_scale_set_fmt: req(80, 60) src out(0, 0)
[ 2.308853] rkcif rkcif-mipi-lvds2: No memory-region-thunderboot specified
[ 2.309472] rockchip-mipi-csi2-hw fdd10000.mipi0-csi2-hw: enter mipi csi2 hw probe!
[ 2.309530] rockchip-mipi-csi2-hw fdd10000.mipi0-csi2-hw: probe success, v4l2_dev:mipi0-csi2-hw!
[ 2.309556] rockchip-mipi-csi2-hw fdd20000.mipi1-csi2-hw: enter mipi csi2 hw probe!
[ 2.309591] rockchip-mipi-csi2-hw fdd20000.mipi1-csi2-hw: probe success, v4l2_dev:mipi1-csi2-hw!
[ 2.309612] rockchip-mipi-csi2-hw fdd30000.mipi2-csi2-hw: enter mipi csi2 hw probe!
[ 2.309648] rockchip-mipi-csi2-hw fdd30000.mipi2-csi2-hw: probe success, v4l2_dev:mipi2-csi2-hw!
[ 2.309669] rockchip-mipi-csi2-hw fdd40000.mipi3-csi2-hw: enter mipi csi2 hw probe!
[ 2.309702] rockchip-mipi-csi2-hw fdd40000.mipi3-csi2-hw: probe success, v4l2_dev:mipi3-csi2-hw!
[ 2.309722] rockchip-mipi-csi2-hw fdd50000.mipi4-csi2-hw: enter mipi csi2 hw probe!
[ 2.309755] rockchip-mipi-csi2-hw fdd50000.mipi4-csi2-hw: probe success, v4l2_dev:mipi4-csi2-hw!
[ 2.309776] rockchip-mipi-csi2-hw fdd60000.mipi5-csi2-hw: enter mipi csi2 hw probe!
[ 2.309808] rockchip-mipi-csi2-hw fdd60000.mipi5-csi2-hw: probe success, v4l2_dev:mipi5-csi2-hw!
[ 2.310144] rockchip-mipi-csi2 mipi2-csi2: attach to csi2 hw node
[ 2.310161] rkcif rkcif-mipi-lvds2: Entity type for entity rockchip-mipi-csi2 was not initialized!
[ 2.310166] rockchip-mipi-csi2: Async registered subdev
[ 2.310171] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds2!
[ 2.310829] rkisp_hw fdcb0000.rkisp: Adding to iommu group 14
[ 2.310913] rkisp_hw fdcb0000.rkisp: is_thunderboot: 0
[ 2.310918] rkisp_hw fdcb0000.rkisp: Missing rockchip,grf property
[ 2.310931] rkisp_hw fdcb0000.rkisp: max input:0x0@0fps
[ 2.310982] rkisp_hw fdcb0000.rkisp: no find phandle sram
[ 2.311148] rkisp rkisp0-vir0: rkisp driver version: v02.04.00
[ 2.311201] rkisp rkisp0-vir0: No memory-region-thunderboot specified
[ 2.311273] rkisp rkisp0-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 2.314050] rk_hdmirx fdee0000.hdmirx-controller: No reserved memory for HDMIRX, use default CMA
[ 2.314088] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_probe: cpu_aff:0x500, Bound_cpu:5, wdt_cfg_bound_cpu:6, phy_cpuid:5
[ 2.314617] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_interrupts_setup: 0
[ 2.315285] rk_hdmirx fdee0000.hdmirx-controller: rk_hdmirx_hdcp_register success
[ 2.315306] rk_hdmirx fdee0000.hdmirx-controller: fdee0000.hdmirx-controller driver probe ok!
[ 2.315394] usbcore: registered new interface driver uvcvideo
[ 2.315398] USB Video Class driver (1.1.1)
[ 2.316021] Bluetooth: HCI UART driver ver 2.3
[ 2.316027] Bluetooth: HCI UART protocol H4 registered
[ 2.316030] Bluetooth: HCI UART protocol ATH3K registered
[ 2.316052] usbcore: registered new interface driver bfusb
[ 2.316069] usbcore: registered new interface driver btusb
[ 2.316819] cpu cpu0: bin=0
[ 2.317046] cpu cpu0: leakage=10
[ 2.318457] cpu cpu0: pvtm=1439
[ 2.318564] cpu cpu0: pvtm-volt-sel=2
[ 2.320414] cpu cpu4: bin=0
[ 2.320622] cpu cpu4: leakage=8
[ 2.327077] cpu cpu4: pvtm=1664
[ 2.330982] cpu cpu4: pvtm-volt-sel=3
[ 2.333594] cpu cpu6: bin=0
[ 2.333802] cpu cpu6: leakage=8
[ 2.340232] cpu cpu6: pvtm=1668
[ 2.344121] cpu cpu6: pvtm-volt-sel=3
[ 2.345863] cpu cpu0: avs=0
[ 2.346845] cpu cpu4: avs=0
[ 2.347664] cpu cpu6: avs=0
[ 2.347845] cpu cpu0: EM: created perf domain
[ 2.347874] cpu cpu0: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=1608000000 h_table=0
[ 2.348391] cpu cpu4: EM: created perf domain
[ 2.348424] cpu cpu4: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[ 2.356858] cpu cpu6: EM: created perf domain
[ 2.357166] cpu cpu6: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=2208000000 h_table=0
[ 2.366802] sdhci: Secure Digital Host Controller Interface driver
[ 2.366826] sdhci: Copyright(c) Pierre Ossman
[ 2.366832] Synopsys Designware Multimedia Card Interface Driver
[ 2.367488] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.367779] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 2.367785] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 2.367877] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 2.367895] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 2.367902] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 2.367923] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 2.368049] dwmmc_rockchip fe2c0000.mmc: No normal pinctrl state
[ 2.368059] dwmmc_rockchip fe2c0000.mmc: No idle pinctrl state
[ 2.368204] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode.
[ 2.368230] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller.
[ 2.368240] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a
[ 2.368269] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 91,32 bit host data width,256 deep fifo
[ 2.368805] dwmmc_rockchip fe2c0000.mmc: Failed getting OCR mask: -22
[ 2.368929] dwmmc_rockchip fe2c0000.mmc: could not set regulator OCR (-22)
[ 2.368937] dwmmc_rockchip fe2c0000.mmc: failed to enable vmmc regulator
[ 2.369234] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[ 2.369285] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[ 2.369915] cryptodev: driver 1.12 loaded.
[ 2.369945] hid: raw HID events driver (C) Jiri Kosina
[ 2.370147] usbcore: registered new interface driver usbhid
[ 2.370153] usbhid: USB HID core driver
[ 2.373743] optee: probing for conduit method.
[ 2.373762] optee: revision 3.13 (62aa10b7)
[ 2.373883] optee: dynamic shared memory is enabled
[ 2.374000] optee: initialized driver
[ 2.374393] usbcore: registered new interface driver snd-usb-audio
[ 2.375512] ES8323 7-0011: i2c recv Failed
[ 2.378271] rockchip-i2s-tdm fddf0000.i2s: CLK-ALWAYS-ON: mclk: 12288000, bclk: 3072000, fsync: 48000
[ 2.379266] rockchip-i2s-tdm fddf4000.i2s: CLK-ALWAYS-ON: mclk: 12288000, bclk: 3072000, fsync: 48000
[ 2.381546] debugfs: File 'Capture' in directory 'dapm' already present!
[ 2.381581] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 2.393681] input: rockchip,hdmiin rockchip,hdmiin as /devices/platform/hdmiin-sound/sound/card0/input1
[ 2.394983] Initializing XFRM netlink socket
[ 2.395333] NET: Registered protocol family 10
[ 2.395926] Segment Routing with IPv6
[ 2.395973] NET: Registered protocol family 17
[ 2.395987] NET: Registered protocol family 15
[ 2.396124] Bluetooth: RFCOMM socket layer initialized
[ 2.396137] Bluetooth: RFCOMM ver 1.11
[ 2.396147] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.396155] Bluetooth: HIDP socket layer initialized
[ 2.396182] [BT_RFKILL]: Enter rfkill_rk_init
[ 2.396187] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 2.396524] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 2.396549] [WLAN_RFKILL]: can't find rockchip,grf property
[ 2.396556] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6398s
[ 2.396561] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 2.396567] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 2.396582] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 20 flags = 0.
[ 2.396602] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 10, flags = 0.
[ 2.396609] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 2.396615] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 2.396621] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 2.396627] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 2.396890] Key type dns_resolver registered
[ 2.397724] imx415 3-001a: driver version: 00.01.08
[ 2.397741] imx415 3-001a: Get hdr mode failed! no hdr default
[ 2.397756] imx415 3-001a: detect imx415 lane 4
[ 2.397780] imx415 3-001a: Failed to get reset-gpios
[ 2.397795] imx415 3-001a: Failed to get power-gpios
[ 2.397803] imx415 3-001a: could not get default pinstate
[ 2.397809] imx415 3-001a: could not get sleep pinstate
[ 2.398434] mmc0: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA
[ 2.399131] imx415 3-001a: supply dvdd not found, using dummy regulator
[ 2.399217] imx415 3-001a: supply dovdd not found, using dummy regulator
[ 2.434321] mmc0: Host Software Queue enabled
[ 2.434335] mmc0: new HS400 Enhanced strobe MMC card at address 0001
[ 2.434637] mmcblk0: mmc0:0001 A3A55B 28.9 GiB
[ 2.434734] mmcblk0boot0: mmc0:0001 A3A55B partition 1 4.00 MiB
[ 2.434829] mmcblk0boot1: mmc0:0001 A3A55B partition 2 4.00 MiB
[ 2.434939] mmcblk0rpmb: mmc0:0001 A3A55B partition 3 16.0 MiB, chardev (236:0)
[ 2.436766] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 2.468743] imx415 3-001a: Unexpected sensor id(000000), ret(-5)
[ 2.469397] Loading compiled-in X.509 certificates
[ 2.470136] pstore: Using crash dump compression: deflate
[ 2.470445] rga3_core0 fdb60000.rga: Adding to iommu group 2
[ 2.470633] rga: rga3_core0, irq = 36, match scheduler
[ 2.470979] rga: rga3_core0 hardware loaded successfully, hw_version:3.0.76831.
[ 2.471025] rga: rga3_core0 probe successfully
[ 2.471479] rga3_core1 fdb70000.rga: Adding to iommu group 3
[ 2.471648] rga: rga3_core1, irq = 37, match scheduler
[ 2.472078] rga: rga3_core1 hardware loaded successfully, hw_version:3.0.76831.
[ 2.472129] rga: rga3_core1 probe successfully
[ 2.472545] rga: rga2, irq = 38, match scheduler
[ 2.472987] rga: rga2 hardware loaded successfully, hw_version:3.2.63318.
[ 2.473000] rga: rga2 probe successfully
[ 2.473242] rga_iommu: IOMMU binding successfully, default mapping core[0x1]
[ 2.473423] rga: Module initialized. v1.3.1
[ 2.498482] mali fb000000.gpu: Kernel DDK version g18p0-01eac0
[ 2.498760] pcie20_avdd0v85: supplied by vdd_0v85_s0
[ 2.499291] pcie20_avdd1v8: supplied by avcc_1v8_s0
[ 2.499342] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 2.499352] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 2.499387] mali fb000000.gpu: bin=0
[ 2.499445] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 2.499475] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 2.499485] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 2.499506] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 2.499618] mali fb000000.gpu: leakage=12
[ 2.499669] debugfs: Directory 'fb000000.gpu-mali' with parent 'vdd_gpu_s0' already present!
[ 2.499725] pcie30_avdd0v75: supplied by avdd_0v75_s0
[ 2.500217] pcie30_avdd1v8: supplied by avcc_1v8_s0
[ 2.500598] vcc3v3_lcd0_n: supplied by vcc_1v8_s0
[ 2.501078] mali fb000000.gpu: pvtm=868
[ 2.501312] mali fb000000.gpu: pvtm-volt-sel=3
[ 2.501348] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[ 2.501638] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[ 2.502526] mali fb000000.gpu: avs=0
[ 2.502553] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 2.502713] mpp_rkvenc2 fdbd0000.rkvenc-core: bin=0
[ 2.502959] mpp_rkvenc2 fdbd0000.rkvenc-core: leakage=10
[ 2.502970] mpp_rkvenc2 fdbd0000.rkvenc-core: leakage-volt-sel=0
[ 2.503066] mali fb000000.gpu: r0p0 status 5 not found in HW issues table;
[ 2.503075] mali fb000000.gpu: falling back to closest match: r0p0 status 0
[ 2.503081] mali fb000000.gpu: Execution proceeding normally with fallback match
[ 2.503089] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0
[ 2.503132] mali fb000000.gpu: No priority control manager is configured
[ 2.503260] mali fb000000.gpu: No memory group manager is configured
[ 2.503282] mali fb000000.gpu: Protected memory allocator not available
[ 2.503617] mpp_rkvenc2 fdbd0000.rkvenc-core: avs=0
[ 2.503646] mpp_rkvenc2 fdbd0000.rkvenc-core: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 2.503997] mali fb000000.gpu: Capping CSF_FIRMWARE_TIMEOUT to CSF_FIRMWARE_PING_TIMEOUT
[ 2.504194] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[ 2.504447] mali fb000000.gpu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[ 2.504552] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[ 2.504740] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[ 2.505041] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[ 2.507624] vendor storage:20190527 ret = 0
[ 2.512841] mpp_rkvenc2 fdbe0000.rkvenc-core: bin=0
[ 2.512979] mali fb000000.gpu: Probed as mali0
[ 2.513047] mpp_rkvenc2 fdbe0000.rkvenc-core: leakage=10
[ 2.513056] mpp_rkvenc2 fdbe0000.rkvenc-core: leakage-volt-sel=0
[ 2.513620] mpp_rkvenc2 fdbe0000.rkvenc-core: avs=0
[ 2.513636] mpp_rkvenc2 fdbe0000.rkvenc-core: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 2.533393] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[ 2.533662] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[ 2.545140] rockchip-dmc dmc: bin=0
[ 2.545356] rockchip-dmc dmc: leakage=30
[ 2.545376] rockchip-dmc dmc: leakage-volt-sel=0
[ 2.545397] rockchip-dmc dmc: soc version=0, speed=0
[ 2.546483] rockchip-dmc dmc: avs=0
[ 2.546504] rockchip-dmc dmc: current ATF version 0x100
[ 2.546638] rockchip-dmc dmc: normal_rate = 1560000000
[ 2.546[652] rockchip-dmc dmc: reboot_rate = 2112000000
[ 2.546663] rockchip-dmc dmc: suspend_rate = 528000000
[ 2.546674] rockchip-dmc dmc: video_4k_rate = 1560000000
[ 2.546685] rockchip-dmc dmc: video_4k_10b_rate = 1560000000
[ 2.546696] rockchip-dmc dmc: video_svep_rate = 1560000000
[ 2.546707] rockchip-dmc dmc: boost_rate = 2112000000
[ 2.546717] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 2112000000
[ 2.546728] rockchip-dmc dmc: performance_rate = 2112000000
[ 2.546740] rockchip-dmc dmc: hdmirx_rate = 2112000000
[ 2.546750] rockchip-dmc dmc: deep_suspend_rate = 2112000000
[ 2.546765] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
[ 2.546774] rockchip-dmc dmc: failed to get vop pn to msch rl
[ 2.546944] rockchip-dmc dmc: l=10000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 2.547744] rockchip-dmc dmc: could not find power_model node
ddr_m0]E: waiting_vop_line_flag-1958: vop_post=0 unsupported!
[ 2.557929] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[ 2.569622] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[ 2.569700] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[ 2.569723] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[ 2.569744] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[ 2.570288] [drm] failed to init overlay plane Cluster0-win1
[ 2.570358] [drm] failed to init overlay plane Cluster1-win1
[ 2.570422] [drm] failed to init overlay plane Cluster2-win1
[ 2.570486] [drm] failed to init overlay plane Cluster3-win1
[ 2.599155] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc009360870)
[ 2.600460] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[ 2.602189] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.10.auto: dw_hdcp_qp_hdcp_probe success
[ 2.602299] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc00936f400)
[ 2.604247] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[ 2.605727] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.13.auto: dw_hdcp_qp_hdcp_probe success
[ 2.605850] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc00936f400)
[ 2.605966] rockchip-drm display-subsystem: bound fde20000.dsi (ops 0xffffffc009371c18)
[ 2.606066] rockchip-drm display-subsystem: bound fde50000.dp (ops 0xffffffc009371fa8)
[ 2.606148] rockchip-drm display-subsystem: bound fde60000.dp (ops 0xffffffc009371fa8)
[ 2.608046] rockchip-drm display-subsystem: route-hdmi0: failed to get logo,offset
[ 2.608700] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.609026] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.609389] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.609712] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.610047] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.610405] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.610415] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 2.610424] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ddr_m0]E: waiting_vop_line_flag-1958: vop_post=0 unsupported!
[ 2.614598] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 2.614711] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 2.632929] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.633025] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.633396] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.633756] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.634112] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.634525] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.634894] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.635260] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 2.635274] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 2.635285] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 2.666687] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 2.677347] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[ 2.678939] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[ 2.679545] input: adc-keys as /devices/platform/adc-keys/input/input2
[ 2.682583] input: rockchip-hdmi0 rockchip-hdmi0 as /devices/platform/hdmi0-sound/sound/card1/input3
[ 2.684912] input: rockchip-hdmi1 rockchip-hdmi1 as /devices/platform/hdmi1-sound/sound/card2/input4
[ 2.688773] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 2.688830] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 2.688978] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 2.689027] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 2.689047] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 2.689086] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 2.692487] rkcif rkcif-mipi-lvds2: clear unready subdev num: 1
[ 2.693343] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.693427] rkcif-mipi-lvds2: Async subdev notifier completed
[ 2.693458] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.693470] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[ 2.693550] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 2.693569] rkcif-mipi-lvds2: There is not terminal subdev, not synchronized with ISP
[ 2.696021] RKNPU fdab0000.npu: Adding to iommu group 0
[ 2.696307] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[ 2.698040] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff]
[ 2.698072] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff]
[ 2.698095] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff]
[ 2.698769] [drm] Initialized rknpu 0.9.3 20231121 for fdab0000.npu on minor 1
[ 2.703100] RKNPU fdab0000.npu: RKNPU: bin=0
[ 2.703370] RKNPU fdab0000.npu: leakage=7
[ 2.703439] debugfs: Directory 'fdab0000.npu-rknpu' with parent 'vdd_npu_s0' already present!
[ 2.711619] RKNPU fdab0000.npu: pvtm=881
[ 2.716902] RKNPU fdab0000.npu: pvtm-volt-sel=3
[ 2.718820] RKNPU fdab0000.npu: avs=0
[ 2.719118] RKNPU fdab0000.npu: l=10000 h=85000 hyst=5000 l_limit=0 h_limit=800000000 h_table=0
[ 2.731375] RKNPU fdab0000.npu: failed to find power_model node
[ 2.731435] RKNPU fdab0000.npu: RKNPU: failed to initialize power model
[ 2.731450] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient
[ 2.733991] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.737947] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 2.738025] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 2.738224] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 2.738291] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 2.738321] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 2.738379] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 2.739772] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.742396] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 2.743489] rockchip-suspend not set sleep-mode-config for mem-lite
[ 2.743511] rockchip-suspend not set wakeup-config for mem-lite
[ 2.743535] rockchip-suspend not set sleep-mode-config for mem-ultra
[ 2.743551] rockchip-suspend not set wakeup-config for mem-ultra
[ 2.747094] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '13:44:08', on 'Dec 11 2025'.
[ 2.748570] Mali:
[ 2.748578] Mali device driver loaded
[ 2.748619] rkisp rkisp0-vir0: clear unready subdev num: 1
[ 2.748997] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.749025] cfg80211: failed to load regulatory.db
[ 2.749124] rkisp0-vir0: Async subdev notifier completed
[ 2.749160] ALSA device list:
[ 2.749178] #0: rockchip,hdmiin
[ 2.749195] #1: rockchip-hdmi0
[ 2.749210] #2: rockchip-hdmi1
[ 2.751498] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 2.751529] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 2.751679] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 2.751731] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 2.751806] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 2.751860] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 2.765353] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[ 2.765387] VFS: Mounted root (ext4 filesystem) on device 179:6.
[ 2.765892] devtmpfs: mounted
[ 2.769411] Freeing unused kernel memory: 6720K
[ 2.805417] Run /sbin/init as init process
[ 2.848583] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ 2.943557] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
[ 2.968883] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
Start mounting all internal partitions in /etc/fstab
Log saved to /var/log/mount-all.log
Note: Will skip fsck, remove /.skip_fsck to enable
[2]: Handling /dev/mmcblk0p8 /userdata ext4 defaults 2
[0]: Handling /dev/mmcblk0p6 / ext4 rw,noauto 1
[1]: Handling /dev/mmcblk0p7 /oem ext4 defaults 2
[2]: Already resized /dev/mmcblk0p8(ext4)
[1]: Already resized /dev/mmcblk0p7(ext4)
[0]: Already resized /dev/mmcblk0p6(ext4)
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
Populating /dev using udev: [ 3.098132] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.098381] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.098998] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.099306] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.099610] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.099916] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.099924] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 3.099931] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 3.104867] udevd[397]: starting version 3.2.10
[ 3.125314] udevd[401]: starting eudev-3.2.10
[ 3.131707] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 3.143400] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.143642] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.143868] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.144098] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.144323] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.144561] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.144569] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 3.144577] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 3.175423] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 3.178326] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.178711] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.178922] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.179039] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.179156] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.225873] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 3.225879] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 3.225886] stream_cif_mipi_id1: update sensor info failed -19
[ 3.225888] rkcif_tools_id2: update sensor info failed -19
[ 3.226533] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 3.226538] stream_cif_mipi_id2: update sensor info failed -19
[ 3.227520] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 3.227527] rkcif_tools_id1: update sensor info failed -19
[ 3.227804] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 3.227825] rkcif_scale_ch0: update sensor info failed -19
[ 3.228194] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 3.228201] rkcif_tools_id0: update sensor info failed -19
[ 3.229414] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 3.229423] rkcif_scale_ch3: update sensor info failed -19
[ 3.229842] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[2] get remote terminal sensor failed!
[ 3.229847] rkcif_scale_ch2: update sensor info failed -19
[ 3.230131] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[1] get remote terminal sensor failed!
[ 3.230141] rkcif_scale_ch1: update sensor info failed -19
[ 3.230454] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
[ 3.230463] stream_cif_mipi_id0: update sensor info failed -19
[ 3.234387] rkcif-mipi-lvds2: rkcif_update_sensor_info: stream[3] get remote terminal sensor failed!
[ 3.234394] stream_cif_mipi_id3: update sensor info failed -19
done
Starting irqbalance: OK
[ 3.281751] dwhdmi-rockchip fdea0000.hdmi: i2c read time out!
[ 3.281764] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-11
[ 3.281769] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
Initializing random number generator: OK
Saving random seed: [ 3.312501] dw-dp fde60000.dp: aux failed to read dpcd: -110
OK
Starting system message bus: [ 3.327521] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.327961] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.328196] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.329148] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.329368] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
done
Starting bluetoothd: OK
Starting network: ln: failed to create symbolic link '': No such file or directory
OK
Failed to detect Wi-Fi/BT chip!
Starting dhcpcd...
dhcpcd-9.4.1 starting
DHCPCD_ARGS: interface not found
dhcpcd exited
Starting ntpd: OK
[ 3.435208] dwhdmi-rockchip fdea0000.hdmi: i2c read time out!
[ 3.435234] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-11
[ 3.435248] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
starting weston... done.
Starting dropbear sshd: OK
Starting pulseaudio: OK
[ 3.466546] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 3.470151] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.470388] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.470500] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.470628] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.470847] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.471072] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.471080] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 3.471090] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
Starting dnsmasq: OK
[ 3.502561] dw-dp fde60000.dp: aux failed to read dpcd: -110
Starting input-event-daemon: [ 3.507149] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.507524] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.507733] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.507852] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.507967] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
done
W: [pulseaudio] main.c: This program is not intended to be run as root (unless --system is specified).
W: [pulseaudio] main.c: Compiled with DEPRECATED libsamplerate support!
root@rk3588-buildroot:/# Date: 1970-01-01 UTC
[00:00:02.123] weston 13.0.0
https://wayland.freedesktop.org
Bug reports to: https://gitlab.freedesktop.org/wayland/weston/issues/
Build: 13.0.0
[00:00:02.124] Command line: /usr/bin/weston
[00:00:02.124] OS: Linux, 5.10.198, #2 SMP Mon Dec 15 16:00:23 CST 2025, aarch64
[00:00:02.124] Flight recorder: enabled
[00:00:02.124] warning: XDG_RUNTIME_DIR "/var/run" is not configured
correctly. Unix access mode must be 0700 (current mode is 0755),
and must be owned by the user UID 0 (current owner is UID 0).
Refer to your distribution on how to get it, or
http://www.freedesktop.org/wiki/Specifications/basedir-spec
on how to implement it.
/etc/xdg/weston/weston.ini.d/02-desktop.ini: "shell/locking" from "false" to "true"
[00:00:02.126] Using config file '/etc/xdg/weston/weston.ini'
[00:00:02.126] Output repaint window is -1 ms maximum.
[00:00:02.127] Loading module '/usr/lib/libweston-13/drm-backend.so'
[00:00:02.130] initializing drm backend
[00:00:02.130] Entering mirror mode.
[00:00:02.130] Trying direct launcher...
[00:00:02.132] using /dev/dri/card0
[00:00:02.132] DRM: does not support atomic modesetting
[00:00:02.132] DRM: does not support GBM modifiers
[00:00:02.132] DRM: does not support async page flipping
[00:00:02.132] DRM: supports picture aspect ratio
[ 3.597349] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_startup: device is no connected or audio is off
[ 3.597369] hdmi-audio-codec hdmi-audio-codec.7.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 3.608853] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_startup: device is no connected or audio is off
[ 3.608891] hdmi-audio-codec hdmi-audio-codec.7.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 3.611860] dwhdmi-rockchip fdea0000.hdmi: i2c read time out!
[ 3.611892] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-11
[ 3.611902] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 3.620841] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_audio_startup: device is no connected or audio is off
[ 3.620872] hdmi-audio-codec hdmi-audio-codec.7.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
E: [pulseaudio] module-alsa-card.c: Failed to find a working profile.
E: [pulseaudio] module.c: Failed to load module "module-alsa-card" (argument: "device_id="0" name="platform-hdmiin-sound" card_name="alsa_card.platform-hdmiin-sound" namereg_fail=false tsched=no fixed_latency_range=no ignore_dB=no deferred_volume=yes use_ucm=yes avoid_resampling=no card_properties="module-udev-detect.discovered=1""): initialization failed.
E: [pulseaudio] module-rescue-streams.c: module-rescue-stream is obsolete and should no longer be loaded. Please remove it from your configuration.
E: [pulseaudio] module-console-kit.c: GetSessionsForUnixUser() call failed: org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.ConsoleKit was not provided by any .service files
[ 3.642577] dw-dp fde60000.dp: aux failed to read dpcd: -110
E: [pulseaudio] module.c: Failed to load module "module-console-kit" (argument: ""): initialization failed.
[00:00:02.187] Loading module '/usr/lib/libweston-13/gl-renderer.so'
W: [pulseaudio] server-lookup.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
W: [pulseaudio] main.c: Unable to contact D-Bus: org.freedesktop.DBus.Error.NotSupported: Using X11 for dbus-daemon autolaunch was disabled at compile time, set your DBUS_SESSION_BUS_ADDRESS instead
[ 3.649357] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
arm_release_ver: g13p0-01eac0, rk_so_ver: 10
[ 3.649941] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.650380] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.650610] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.650975] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.651085] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.651089] dwhdmi-rockchip fdea0000.hdmi: get hdcp1.4 capable failed:-5
[ 3.651093] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 3.661872] mali fb000000.gpu: Loading Mali firmware 0x1010000
[ 3.663515] mali fb000000.gpu: Mali firmware git_sha: ee476db42870778306fa8d559a605a73f13e455c
[00:00:02.217] EGL version: 1.4 Valhall-"g13p0-01eac0"
[00:00:02.217] EGL vendor: ARM
[00:00:02.217] EGL client APIs: OpenGL_ES
[00:00:02.217] EGL features:
EGL Wayland extension: yes
context priority: yes
buffer age: no
partial update: yes
swap buffers with damage: no
configless context: yes
surfaceless context: yes
dmabuf support: modifiers
[ 3.682672] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 3.685051] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.685629] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.685877] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.686485] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[00:00:02.228] GL version: OpenGL ES 3.2 v1.g13p0-01eac0.11addb9882ee8209dc0912af75110af7
[ 3.686713] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[00:00:02.228] GLSL version: OpenGL ES GLSL ES 3.20
[ 3.686937] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[00:00:02.228] GL vendor: ARM
[ 3.686945] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[00:00:02.228] GL renderer: Mali-G610
[ 3.686953] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 3.689887] file system registered
[ 3.718702] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 3.720830] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.721053] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.727503] read descriptors
[ 3.727519] read strings
[00:00:02.311] GL ES 3.2 - renderer features:
read-back format: ARGB8888
glReadPixels supports y-flip: no
wl_shm 10 bpc formats: yes
wl_shm 16 bpc formats: no
wl_shm half-float formats: yes
internal R and RG formats: yes
OES_EGL_image_external: yes
wl_shm sub-image to texture: yes
[00:00:02.311] Using GL renderer
[00:00:02.321] event2 - adc-keys: is tagged by udev as: Keyboard
[00:00:02.321] event2 - adc-keys: device is a keyboard
[00:00:02.322] event0 - rk805 pwrkey: is tagged by udev as: Keyboard
[00:00:02.322] event0 - rk805 pwrkey: device is a keyboard
[00:00:02.323] event3 - rockchip-hdmi0 rockchip-hdmi0: is tagged by udev as: Switch
[00:00:02.324] event3 - not using input device '/dev/input/event3'
[00:00:02.324] event4 - rockchip-hdmi1 rockchip-hdmi1: is tagged by udev as: Switch
[00:00:02.325] event4 - not using input device '/dev/input/event4'
[00:00:02.325] event1 - rockchip,hdmiin rockchip,hdmiin: is tagged by udev as: Switch
[00:00:02.326] event1 - not using input device '/dev/input/event1'
[00:00:02.358] libinput: configuring device "adc-keys".
[00:00:02.358] libinput: configuring device "rk805 pwrkey".
[00:00:02.359] Registered plugin API 'weston_drm_output_api_v1' of size 40
[00:00:02.359] Color manager: no-op
[00:00:02.359] Compositor capabilities:
arbitrary surface rotation: yes
screen capture uses y-flip: yes
cursor planes: yes
arbitrary resolutions: no
view mask clipping: yes
explicit sync: yes
color operations: yes
presentation clock: CLOCK_MONOTONIC, id 1
presentation clock resolution: 0.000000001 s
[00:00:02.359] Loading module '/usr/lib/weston/desktop-shell.so'
[ 3.821977] dwhdmi-rockchip fdea0000.hdmi: i2c read time out!
[ 3.822869] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.823338] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.823595] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 3.853814] dw-dp fde60000.dp: aux failed to read dpcd: -110
[00:00:02.395] DRM: head 'HDMI-A-1' found, connector 208 is disconnected.
[ 3.854481] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.854828] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.855232] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.855584] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.855928] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 3.856304] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[00:00:02.398] DRM: head 'HDMI-A-2' found, connector 224 is connected, EDID make 'unknown', model 'unknown', serial ''
[ 3.856752] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
Supported EOTF modes: SDR
[00:00:02.398] DRM: head 'DSI-1' found, connector 238 is connected, EDID make 'unknown', model 'unknown', serial ''
Supported EOTF modes: SDR
[00:00:02.399] DRM: head 'DP-1' found, connector 240 is disconnected.
[ 3.891023] dw-dp fde60000.dp: aux failed to read dpcd: -110
[00:00:02.432] DRM: head 'DP-2' found, connector 248 is disconnected.
[00:00:02.433] launching '/usr/libexec/weston-keyboard'
[00:00:02.434] launching '/usr/libexec/weston-desktop-shell'
[00:00:02.435] HDMI-A-2 using at least 2 buffers
[00:00:02.436] Output 'HDMI-A-2' attempts EOTF mode: SDR
[00:00:02.436] Output 'HDMI-A-2' using color profile: stock sRGB color profile
[00:00:02.436] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[00:00:02.436] Output HDMI-A-2 (crtc 93) video modes:
1920x1080@60.0 16:9, preferred, current, 148.5 MHz
1920x1080@50.0 16:9, 148.5 MHz
[ 3.898135] android_work: did not send uevent (0 0 0000000000000000)
1280x720@60.0 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
1920x1080@60.0, preferred, 148.5 MHz
[00:00:02.436] associating input device event2 with output HDMI-A-2 (none by udev)
[00:00:02.436] associating input device event0 with output HDMI-A-2 (none by udev)
[00:00:02.436] Output HDMI-A-2 changed to mirror output
[00:00:02.436] Output 'HDMI-A-2' enabled with head(s) HDMI-A-2
[00:00:02.437] DSI-1 using at least 2 buffers
[00:00:02.437] Output 'DSI-1' attempts EOTF mode: SDR
[00:00:02.437] Output 'DSI-1' using color profile: stock sRGB color profile
[00:00:02.437] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[00:00:02.437] Output DSI-1 (crtc 137) video modes:
1024x600@56.1, preferred, current, 45.0 MHz
[00:00:02.437] associating input device event2 with output DSI-1 (none by udev)
[00:00:02.437] associating input device event0 with output DSI-1 (none by udev)
[00:00:02.437] Output 'DSI-1' enabled with head(s) DSI-1
[ 3.912729] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 3.962978] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp1
[ 4.050989] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:1000, flag:0x0) for vp1 dclk: 148500000
[ 4.051060] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] dclk_out1 div: 0 dclk_core1 div: 2
[ 4.051076] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] set dclk_vop1 to 148500000, get 148500000
[ 4.051141] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
[ 4.051426] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy pll locked!
[ 4.051434] dwhdmi-rockchip fdea0000.hdmi: final tmdsclk = 148500000
[ 4.051469] dwhdmi-rockchip fdea0000.hdmi: don't use dsc mode
[ 4.051476] dwhdmi-rockchip fdea0000.hdmi: dw hdmi qp use tmds mode
[ 4.051485] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: bus_width:0x16a8c8,bit_rate:1485000
[ 4.051685] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy lane locked!
[ 4.084551] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
could not load cursor 'dnd-move'
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
could not load cursor 'dnd-none'
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
could not create XKB compose table for locale 'en_US.UTF-8'. Disabiling compose
[ 4.506249] rk_hdmirx fdee0000.hdmirx-controller: hdmirx_cancel_cpu_limit_freq freq qos nod add
xkbcommon: ERROR: couldn't find a Compose file for locale "en_US.UTF-8" (mapped to "en_US.UTF-8")
could not create XKB compose table for locale 'en_US.UTF-8'. Disabiling compose
[ 4.778651] rk-pcie fe170000.pcie: PCIe Link Fail, LTSSM is 0x3, hw_retries=0
[ 4.805224] rk-pcie fe150000.pcie: PCIe Link Fail, LTSSM is 0x0, hw_retries=0
[ 4.805303] rk-pcie fe150000.pcie: failed to initialize host
[ 5.135218] Freeing drm_logo memory: 736K
[ 7.101804] rk_pcie_establish_link: 231 callbacks suppressed
[ 7.101808] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.128470] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.155144] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.181849] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.208617] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.235293] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.261961] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.288522] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.315233] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 7.341808] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[ 8.675139] rk-pcie fe170000.pcie: PCIe Link Fail, LTSSM is 0x3, hw_retries=1
[ 9.695423] rk-pcie fe170000.pcie: failed to initialize host
[ 19.006840] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 19.161799] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.162267] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.162684] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.163100] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.163334] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.163564] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.163800] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.163812] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 19.163825] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.199016] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 19.199414] dwhdmi-rockchip fde80000.hdmi: i2c read err!
[ 19.199458] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 19.199472] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 19.199540] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:800, flag:0x0) for vp0 dclk: 148500000
[ 19.199603] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] dclk_out0 div: 0 dclk_core0 div: 2
[ 19.199626] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] set dclk_vop0 to 148500000, get 148500000
[ 19.199674] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
[ 19.199983] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy pll locked!
[ 19.199994] dwhdmi-rockchip fde80000.hdmi: final tmdsclk = 148500000
[ 19.200039] dwhdmi-rockchip fde80000.hdmi: don't use dsc mode
[ 19.200048] dwhdmi-rockchip fde80000.hdmi: dw hdmi qp use tmds mode
[ 19.200061] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: bus_width:0x16a8c8,bit_rate:1485000
[ 19.200278] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy lane locked!
[00:00:17.759] DRM: head 'HDMI-A-1' updated, connector 208 is connected, EDID make 'GSM', model '27MP35', serial ''
[ 19.218566] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
Supported EOTF modes: SDR
[ 19.218887] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.219196] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.219421] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.219646] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.219870] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.220098] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 19.220108] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 19.220115] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 19.254830] dw-dp fde60000.dp: aux failed to read dpcd: -110
[00:00:17.796] Detected a monitor change on head 'HDMI-A-2', not bothering to do anything about it.
[00:00:17.796] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
[00:00:17.796] HDMI-A-1 using at least 2 buffers
[00:00:17.796] Output 'HDMI-A-1' attempts EOTF mode: SDR
[00:00:17.796] Output 'HDMI-A-1' using color profile: stock sRGB color profile
[00:00:17.797] Chosen EGL config details: id: 9 rgba: 8 8 8 0 buf: 24 dep: 0 stcl: 0 int: 0-1 type: win|pbf|swap_preserved vis_id: XRGB8888 (0x34325258)
[00:00:17.797] Output HDMI-A-1 (crtc 71) video modes:
1920x1080@60.0, preferred, current, 148.5 MHz
1920x1080@60.0 16:9, 148.5 MHz
1920x1080i@60.0, 74.2 MHz
1920x1080i@60.0 16:9, 74.2 MHz
1920x1080@50.0 16:9, 148.5 MHz
1920x1080i@50.0 16:9, 74.2 MHz
1600x900@60.0, 108.0 MHz
1280x1024@60.0, 108.0 MHz
1152x864@75.0, 108.0 MHz
1280x720@60.0, 74.2 MHz
1280x720@60.0 16:9, 74.2 MHz
1280x720@50.0 16:9, 74.2 MHz
800x600@75.0, 49.5 MHz
720x576@50.0 16:9, 27.0 MHz
720x480@59.9, 27.0 MHz
720x480@59.9 16:9, 27.0 MHz
[00:00:17.797] Output HDMI-A-1 changed to mirror output
[00:00:17.797] Output 'HDMI-A-1' enabled with head(s) HDMI-A-1
[ 19.265994] dwhdmi-rockchip fde80000.hdmi: use tmds mode
[ 19.283177] dwhdmi-rockchip fde80000.hdmi: use tmds mode
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 28.691377] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 28.691646] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.692585] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.692933] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.693165] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.693396] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.693633] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.693645] dwhdmi-rockchip fdea0000.hdmi: get hdcp2.x capable failed:-5
[ 28.693659] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 28.728690] dw-dp fde60000.dp: aux failed to read dpcd: -110
[ 28.728877] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 28.779190] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
[00:00:27.357] DRM: head 'HDMI-A-1' updated, connector 208 is disconnected.
[ 28.816664] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.817756] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.819223] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.821993] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.822933] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.838950] dwhdmi-rockchip fdea0000.hdmi: i2c read err!
[ 28.839379] dwhdmi-rockchip fdea0000.hdmi: failed to get edid
[ 28.875001] dw-dp fde60000.dp: aux failed to read dpcd: -110
[00:00:27.417] Output 'HDMI-A-1' no heads left, disabling.
[00:00:27.417] Disabling output HDMI-A-1
[00:00:27.418] Detected a monitor change on head 'HDMI-A-2', not bothering to do anything about it.
[00:00:27.418] Detected a monitor change on head 'DSI-1', not bothering to do anything about it.
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 33.509280] vcc3v3_lcd0_n: disabling
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 44.714568] dwc3 fc400000.usb: request 0000000022457179 was not queued to ep0out
[ 44.714710] android_work: did not send uevent (0 0 0000000000000000)
[ 44.822692] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[ 44.823204] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 44.823497] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 9
[ 44.823627] xhci-hcd xhci-hcd.15.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 44.823657] xhci-hcd xhci-hcd.15.auto: irq 151, io mem 0xfc400000
[ 44.823764] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 44.823974] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 10
[ 44.823989] xhci-hcd xhci-hcd.15.auto: Host supports USB 3.0 SuperSpeed
[ 44.824089] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 44.824099] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.824108] usb usb9: Product: xHCI Host Controller
[ 44.824116] usb usb9: Manufacturer: Linux 5.10.198 xhci-hcd
[ 44.824124] usb usb9: SerialNumber: xhci-hcd.15.auto
[ 44.824515] hub 9-0:1.0: USB hub found
[ 44.824539] hub 9-0:1.0: 1 port detected
[ 44.824837] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[ 44.824908] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 44.824917] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.824926] usb usb10: Product: xHCI Host Controller
[ 44.824934] usb usb10: Manufacturer: Linux 5.10.198 xhci-hcd
[ 44.824942] usb usb10: SerialNumber: xhci-hcd.15.auto
[ 44.825608] hub 10-0:1.0: USB hub found
[ 44.825640] hub 10-0:1.0: 1 port detected
[ 44.827465] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 44.827482] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 44.827683] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 44.827714] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 44.827725] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 44.827752] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 45.362450] usb 10-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 45.392242] usb 10-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[ 45.392264] usb 10-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 45.392269] usb 10-1: Product: DataTraveler 3.0
[ 45.392274] usb 10-1: Manufacturer: Kingston
[ 45.392278] usb 10-1: SerialNumber: E0D55EA573CDF830C93D1F6C
[ 45.480758] usb-storage 10-1:1.0: USB Mass Storage device detected
[ 45.482527] scsi host1: usb-storage 10-1:1.0
[ 45.489108] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 45.489202] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 45.489506] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 45.489565] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 45.489595] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 45.489653] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 46.496813] scsi 1:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 46.500113] sd 1:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[ 46.500850] sd 1:0:0:0: [sda] Write Protect is off
[ 46.501527] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 46.506660] sda: sda1
[ 46.508319] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 46.510685] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 46.510735] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 46.510835] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 46.510858] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 46.510869] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 46.510892] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 46.625064] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 46.627223] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 010 Device 001: ID 1d6b:0003
Bus 001 Device 001: ID 1d6b:0002
Bus 010 Device 002: ID 0951:1666
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 009 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 92.983761] xhci-hcd xhci-hcd.15.auto: remove, state 1
[ 92.983805] usb usb10: USB disconnect, device number 1
[ 92.983816] usb 10-1: USB disconnect, device number 2
[ 93.085147] xhci-hcd xhci-hcd.15.auto: USB bus 10 deregistered
[ 93.085419] xhci-hcd xhci-hcd.15.auto: remove, state 4
[ 93.085437] usb usb9: USB disconnect, device number 1
[ 93.086351] xhci-hcd xhci-hcd.15.auto: USB bus 9 deregistered
[ 93.326244] android_work: did not send uevent (0 0 0000000000000000)
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 001 Device 001: ID 1d6b:0002
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# [ 106.464861] dwc3 fc400000.usb: request 0000000021b1168c was not queued to ep0out
[ 106.464923] android_work: did not send uevent (0 0 0000000000000000)
[ 106.572317] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[ 106.572361] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 106.572819] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 9
[ 106.572973] xhci-hcd xhci-hcd.15.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
[ 106.573007] xhci-hcd xhci-hcd.15.auto: irq 151, io mem 0xfc400000
[ 106.573132] xhci-hcd xhci-hcd.15.auto: xHCI Host Controller
[ 106.573307] xhci-hcd xhci-hcd.15.auto: new USB bus registered, assigned bus number 10
[ 106.573322] xhci-hcd xhci-hcd.15.auto: Host supports USB 3.0 SuperSpeed
[ 106.573430] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[ 106.573441] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 106.573449] usb usb9: Product: xHCI Host Controller
[ 106.573457] usb usb9: Manufacturer: Linux 5.10.198 xhci-hcd
[ 106.573465] usb usb9: SerialNumber: xhci-hcd.15.auto
[ 106.573869] hub 9-0:1.0: USB hub found
[ 106.573895] hub 9-0:1.0: 1 port detected
[ 106.574191] usb usb10: We don't know the algorithms for LPM for this host, disabling LPM.
[ 106.574263] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[ 106.574273] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 106.574281] usb usb10: Product: xHCI Host Controller
[ 106.574289] usb usb10: Manufacturer: Linux 5.10.198 xhci-hcd
[ 106.574298] usb usb10: SerialNumber: xhci-hcd.15.auto
[ 106.574697] hub 10-0:1.0: USB hub found
[ 106.574720] hub 10-0:1.0: 1 port detected
[ 106.576562] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 106.576574] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 106.576675] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 106.576697] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 106.576707] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 106.576732] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 107.109039] usb 10-1: new SuperSpeed Gen 1 USB device number 2 using xhci-hcd
[ 107.138799] usb 10-1: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[ 107.138807] usb 10-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 107.138809] usb 10-1: Product: DataTraveler 3.0
[ 107.138811] usb 10-1: Manufacturer: Kingston
[ 107.138813] usb 10-1: SerialNumber: E0D55EA573CDF830C93D1F6C
[ 107.226872] usb-storage 10-1:1.0: USB Mass Storage device detected
[ 107.228276] scsi host1: usb-storage 10-1:1.0
[ 107.230656] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 107.230687] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 107.230835] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 107.230860] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 107.230871] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 107.230894] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 108.256951] scsi 1:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6
[ 108.260146] sd 1:0:0:0: [sda] 120845300 512-byte logical blocks: (61.9 GB/57.6 GiB)
[ 108.260727] sd 1:0:0:0: [sda] Write Protect is off
[ 108.261318] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 108.266613] sda: sda1
[ 108.269764] sd 1:0:0:0: [sda] Attached SCSI removable disk
[ 108.271485] dwmmc_rockchip fe2d0000.mmc: No normal pinctrl state
[ 108.271510] dwmmc_rockchip fe2d0000.mmc: No idle pinctrl state
[ 108.271602] dwmmc_rockchip fe2d0000.mmc: IDMAC supports 32-bit address mode.
[ 108.271622] dwmmc_rockchip fe2d0000.mmc: Using internal DMA controller.
[ 108.271631] dwmmc_rockchip fe2d0000.mmc: Version ID is 270a
[ 108.271652] dwmmc_rockchip fe2d0000.mmc: DW MMC controller at irq 92,32 bit host data width,256 deep fifo
[ 108.380628] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 108.384109] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# lsusb
Bus 005 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 010 Device 001: ID 1d6b:0003
Bus 001 Device 001: ID 1d6b:0002
Bus 010 Device 002: ID 0951:1666
Bus 008 Device 001: ID 1d6b:0003
Bus 006 Device 001: ID 1d6b:0003
Bus 004 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002
Bus 009 Device 001: ID 1d6b:0002
Bus 007 Device 001: ID 1d6b:0002
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/#
root@rk3588-buildroot:/# poweroff
root@rk3588-buildroot:/# Stopping input-event-daemon: done
stop auto-reboot finished
Stopping dnsmasq: OK
Stopping pulseaudio: E: [pulseaudio] main.c: Failed to kill daemon: No such process
OK
Stopping dropbear sshd: OK
stoping weston... [00:02:09.813] caught signal 15
done.
[00:02:09.814] event2 - adc-keys: device removed
[00:02:09.814] event0 - rk805 pwrkey: device removed
Stopping ntpd: OK
Stopping dhcpcd...
no /sbin/dhcpcd found; none killed
killall: rkaiq_3A_server: no process killed
Stopping network: OK
Stopping bluetoothd: OK
[ 131.345128] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp3
Stopping Wi-Fi/BT...
Stopping system message bus: done
Saving random seed: OK
Stopping irqbalance: OK
[ 131.431152] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp1
Stopping klogd: OK
Stopping syslogd: OK
[ 131.471425] ffs_data_put(): freeing
umount: /var/log: target is busy.
umount: /run: target is busy.
[ 131.494538] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
The system is going down NOW!
Sent SIGTERM to all processes
E: [pulseaudio] module-default-device-restore.c: Failed to save default sink: No such file or directory
E: [pulseaudio] module-default-device-restore.c: Failed to save default source: No such file or directory
E: [pulseaudio] core-util.c: Failed to create secure directory (/userdata/.pulse/.config/pulse): No such file or directory
[ 131.503359] dwhdmi-rockchip fdea0000.hdmi: use tmds mode
[ 131.506657] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type: 11(if:1000, flag:0x0) for vp1 dclk: 148500000
[ 131.507264] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] dclk_out1 div: 0 dclk_core1 div: 2
[ 131.507285] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] set dclk_vop1 to 148500000, get 148500000
[ 131.540744] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] Update mode to 1024x600p56, type: 16(if:20, flag:0x0) for vp3 dclk: 44118000
[ 131.540809] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] dclk_out3 div: 2 dclk_core3 div: 2
[ 131.540825] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_enable] set dclk_vop3 to 44118000, get 44117648
[ 131.559068] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
[ 131.559366] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy pll locked!
[ 131.559379] dwhdmi-rockchip fdea0000.hdmi: final tmdsclk = 148500000
[ 131.559420] dwhdmi-rockchip fdea0000.hdmi: don't use dsc mode
[ 131.559427] dwhdmi-rockchip fdea0000.hdmi: dw hdmi qp use tmds mode
[ 131.559435] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: bus_width:0x16a8c8,bit_rate:1485000
[ 131.559633] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy lane locked!
[ 131.593502] dw-mipi-dsi2 fde20000.dsi: [drm:dw_mipi_dsi2_encoder_atomic_enable] final DSI-Link bandwidth: 294120 x 4 Kbps
Sent SIGKILL to all processes
Requesting system poweroff
[ 133.651625] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp1
[ 133.674111] rockchip-vop2 fdd90000.vop: [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp3
[ 133.739652] mpp_rkvenc2 fdbe0000.rkvenc-core: shutdown device
[ 133.740159] mpp_rkvenc2 fdbe0000.rkvenc-core: shutdown success
[ 133.740667] mpp_rkvenc2 fdbd0000.rkvenc-core: shutdown device
[ 133.741174] mpp_rkvenc2 fdbd0000.rkvenc-core: shutdown success
[ 133.747095] rk860-regulator 1-0042: rk860..... reset
[ 133.748446] rk860-regulator 1-0042: force rk860x_reset ok!
[ 133.748932] rk860-regulator 0-0043: rk860..... reset
[ 133.750292] rk860-regulator 0-0043: force rk860x_reset ok!
[ 133.750778] rk860-regulator 0-0042: rk860..... reset
[ 133.752139] rk860-regulator 0-0042: force rk860x_reset ok!
[ 133.784705] xhci-hcd xhci-hcd.5.auto: Host halt failed, -110
[ 133.785660] mpp_av1dec av1d-master: shutdown device
[ 133.786091] mpp_av1dec av1d-master: shutdown success
[ 133.786616] [WLAN_RFKILL]: Enter rfkill_wlan_shutdown
[ 133.787055] [WLAN_RFKILL]: rockchip_wifi_power: 0
[ 133.787471] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized
[ 133.788260] wifi power off
[ 133.895099] [BT_RFKILL]: rfkill_get_bt_power_state: rfkill-bt driver has not Successful initialized
[ 133.895889] [WLAN_RFKILL]: wifi shut off power [GPIO20-0]
[ 133.896360] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 0
[ 133.897214] rockchip-i2s-tdm fddf8000.i2s: failed to clear 1 on slave mode
[ 133.898178] xhci-hcd xhci-hcd.15.auto: remove, state 1
[ 133.898634] usb usb10: USB disconnect, device number 1
[ 133.899085] usb 10-1: USB disconnect, device number 0
[ 134.098459] usb 10-1: device not accepting address 2, error -108
[ 134.196688] xhci-hcd xhci-hcd.15.auto: USB bus 10 deregistered
[ 134.197388] xhci-hcd xhci-hcd.15.auto: remove, state 4
[ 134.197846] usb usb9: USB disconnect, device number 1
[ 134.198940] xhci-hcd xhci-hcd.15.auto: USB bus 9 deregistered
[ 134.200464] rkisp_hw fdcb0000.rkisp: rkisp_hw_shutdown
[ 134.200952] mpp_rkvdec2 fdc48100.rkvdec-core: shutdown device
[ 134.201461] mpp_rkvdec2 fdc48100.rkvdec-core: shutdown success
[ 134.202010] mpp_rkvdec2 fdc38100.rkvdec-core: shutdown device
[ 134.202521] mpp_rkvdec2 fdc38100.rkvdec-core: shutdown success
[ 134.203106] mpp-iep2 fdbb0000.iep: shutdown device
[ 134.203529] mpp-iep2 fdbb0000.iep: shutdown success
[ 134.203977] mpp_vepu2 fdbac000.jpege-core: shutdown device
[ 134.204464] mpp_vepu2 fdbac000.jpege-core: shutdown success
[ 134.204968] mpp_vepu2 fdba8000.jpege-core: shutdown device
[ 134.205462] mpp_vepu2 fdba8000.jpege-core: shutdown success
[ 134.205966] mpp_vepu2 fdba4000.jpege-core: shutdown device
[ 134.206452] mpp_vepu2 fdba4000.jpege-core: shutdown success
[ 134.206956] mpp_vepu2 fdba0000.jpege-core: shutdown device
[ 134.207442] mpp_vepu2 fdba0000.jpege-core: shutdown success
[ 134.207956] mpp_jpgdec fdb90000.jpegd: shutdown device
[ 134.208416] mpp_jpgdec fdb90000.jpegd: shutdown success
[ 134.208930] mpp_vdpu1 fdb51000.avsd-plus: shutdown device
[ 134.209405] mpp_vdpu1 fdb51000.avsd-plus: shutdown success
[ 134.209895] mpp_vepu2 fdb50000.vepu: shutdown device
[ 134.210336] mpp_vepu2 fdb50000.vepu: shutdown success
[ 134.210781] mpp_vdpu2 fdb50400.vdpu: shutdown device
[ 134.211224] mpp_vdpu2 fdb50400.vdpu: shutdown success
[ 134.211878] xhci-hcd xhci-hcd.6.auto: remove, state 4
[ 134.212325] usb usb8: USB disconnect, device number 1
[ 134.213165] xhci-hcd xhci-hcd.6.auto: USB bus 8 deregistered
[ 134.213835] xhci-hcd xhci-hcd.6.auto: remove, state 4
[ 134.214282] usb usb7: USB disconnect, device number 1
[ 134.215264] xhci-hcd xhci-hcd.6.auto: USB bus 7 deregistered
[ 134.216310] xhci-hcd xhci-hcd.5.auto: remove, state 4
[ 134.216759] usb usb6: USB disconnect, device number 1
[ 134.217581] xhci-hcd xhci-hcd.5.auto: USB bus 6 deregistered
[ 134.218192] xhci-hcd xhci-hcd.5.auto: remove, state 4
[ 134.218651] usb usb5: USB disconnect, device number 1
[ 134.251468] xhci-hcd xhci-hcd.5.auto: Host halt failed, -110
[ 134.251965] xhci-hcd xhci-hcd.5.auto: Host controller not halted, aborting reset.
[ 134.252814] xhci-hcd xhci-hcd.5.auto: USB bus 5 deregistered
[ 134.254292] reboot: Power down
[END] 2025/12/15 21:04:58
扫一扫
733
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
