2020.10.01（401882644@qq.com）
偶然得到一个H3C AP，型号WAP722S-W2，一共有三个口：48V DC、GE1/PoE、console
咨询别人得知这是一个瘦（fit）AP，需要连接AC才能使用，但可以刷成胖（fat）AP，就可以单独作为企业级路由器使用了。想着就来劲，动手干吧。
首先，这个东东是需要电才能用的，到手之前它是使用PoE交换机供电使用的，家里可没有这个，那么就网上淘了一个48V电源，插左边那个48V DC口使用，完全没有问题。除了电源外，还需要用到的硬件有：调试线、网线、电脑；需要用到的软件有：3Cdaemon（TFTP上传升级文件）、putty（telnet软件）、WAP722S-W2对应的升级文件（版本为：R2433P01,本人优快云提供下载，ID：walkerjie）
开始了，先运行3CDaemon，第二个按钮停止服务，第一个按钮设置服务器，把上传/下载目录设置为升级所在文件夹，然后确定，确定。
升级文件夹里的东东，注意，ipe那个后边要改名！
电脑网口设置ip：192.168.0.1
调试线插入电脑usb口，安装驱动，打开putty，配置如下：
点击putty的open按钮，调试线网口那头插入AP的console口，网线一头插电脑，一头插入AP的GE1/PoE口，AP上电：
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.................................
..Done.
****************************************************************************
* *
* H3C WAP722S-W2 BootWare, Version 7.12 这个是bootwarer 版本，后边会升级 *
* *
****************************************************************************
Copyright (c) 2004-2017 New H3C Technologies Co., Ltd.
Compiled Date : Dec 19 2017
CPU Type : ARM
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 710MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB 内存256
Memory Speed : 533MHz
Flash Size : 32MB 存储只有32
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...这里赶紧按Ctrl+B
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
以下是主菜单
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 4先看看里边的文件
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1看看所有文件
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
|1 4296704 Jan/01/2016 00:02:15 M flash:/wa5300-boot.bin |
|2 13932544 Jan/01/2016 00:04:27 M flash:/wa5300-system.bin |
============================================================================
两个文件加一块儿就17MB多了
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0退到上级菜单
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 按下Ctrl+Y看看现在AP运行在什么模式下
Please select the new mode
Current mode is Fit当前运行在Fit模式下
============================================================================
|NO. Mode |
|1 Fat Mode |
|2 Fit Mode |
|0 Exit |
============================================================================
Enter your choice(0-2):0你可以把它改为Fat模式，不过没卵用，重启会找不到相应文件，这里退回主菜单
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 按Ctrl+F格式化flash，原因是它总共只有32MB，不格式化就不能把升级文件下载下来，没那么多空间
Warning:All files on flash will be lost! Are you sure to format? [Y/N]Y.....
............................................................................
..................
Format success.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 4再来看看flash里的情况
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1显示所有文件
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
============================================================================
空空如也
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 0退回上级菜单
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9):7 先升级BootWare，不然决逼失败
=========================<BootWare Operation Menu>==========================
|Note:the operating device is flash |
|<1> Backup Full BootWare |
|<2> Restore Full BootWare |
|<3> Update BootWare By Serial |
|<4> Update BootWare By Ethernet |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4):4网络升级
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4):4先查看配置内容
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :ftp tftp配置为3CDaemon使用的tftp
Load File Name :wa5300-fat.ipe
:apwa5300_7.22.btw改为升级文件夹里的btw文件名
Target File Name :wa5300-fat.ipe
:apwa5300_7.22.btw改为升级文件夹里的btw文件名
Server IP Address :192.168.0.1
Local IP Address :192.168.0.50
Subnet Mask :0.0.0.0
Gateway IP Address :0.0.0.0
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 1升级所有BootWare文件，3CDaemon开启服务
Loading...........................Done.
1241088 bytes downloaded!从3CDaemon下载成功
Updating Basic BootWare? [Y/N]Y肯定选择Y升级
Updating Basic BootWare.........Done.完成
Updating Extended BootWare? [Y/N]Y肯定选择Y升级
Updating Extended BootWare.........Done.完成
===================<BOOTWARE OPERATION ETHERNET SUB-MENU>===================
|<1> Update Full BootWare |
|<2> Update Extended BootWare |
|<3> Update Basic BootWare |
|<4> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 0返回上级
=========================<BootWare Operation Menu>==========================
|Note:the operating device is flash |
|<1> Backup Full BootWare |
|<2> Restore Full BootWare |
|<3> Update BootWare By Serial |
|<4> Update BootWare By Ethernet |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-4): 0返回上级
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 0重启一下
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.................................
............Done.
****************************************************************************
* *
* H3C WAP722S-W2 BootWare, Version 7.22 *
* 注意查看BootWare版本已经升级 *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Apr 16 2020编译日期也是最新的
CPU Type : ARM
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 710MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 533MHz
Flash Size : 32MB
PCB Version : Ver.B
BootWare Validating...
Normal Extended BootWare Version is newer than Backup Extended BootWare!
Begin to Update the Backup Extended BootWare.........Done.
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Password recovery capability is enabled.
Note: The current operating device is flash
Enter < Storage Device Operation > to select device.
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9):3进入Ethernet菜单，准备升级
注意，进行下一步之前，请在升级文件夹内把WA5300-CMW710-R2433P01-OASIS.ipe改名为wa5300-fat.ipe，并在3CDaemon中启动tftp服务
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 5
==========================<ETHERNET PARAMETER SET>==========================
|Note: '.' = Clear field. |
| '-' = Go to previous field. |
| Ctrl+D = Quit. |
============================================================================
Protocol (FTP or TFTP) :tftp
Load File Name :apwa5300_7.22.btw
:wa5300-fat.ipe改为要升级的ipe文件
Target File Name :apwa5300_7.22.btw
:wa5300-fat.ipe改为要升级的ipe文件
Server IP Address :192.168.0.1
Local IP Address :192.168.0.50
Subnet Mask :0.0.0.0
Gateway IP Address :0.0.0.0
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5):2开始升级了
Loading.....................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
............................................................................
...............................Done.
28339200 bytes downloaded!
如下图，同时你会在3CDaemon上看到正在从电脑上下载升级文件
Image file wa5300-oasis-boot.bin is self-decompressing...
Saving file flash:/wa5300-oasis-boot.bin ...................................
.............................Done.
Image file wa5300-oasis-system.bin is self-decompressing...
Saving file flash:/wa5300-oasis-system.bin .................................
............................................................................
............................................................................
............................................................................
............................................................................
.........................................Done.
==========================<Enter Ethernet SubMenu>==========================
|Note:the operating device is flash |
|<1> Download Image Program To SDRAM And Run |
|<2> Update Main Image File |
|<3> Update Backup Image File |
|<4> Download Files(*.*) |
|<5> Modify Ethernet Parameter |
|<0> Exit To Main Menu |
|<Ensure The Parameter Be Modified Before Downloading!> |
============================================================================
Enter your choice(0-5): 0返回上级
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9): 4查看一下升级的文件
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5): 1显示所有文件
Display all file(s) in flash:
'M' = MAIN 'B' = BACKUP 'N/A' = NOT ASSIGNED
============================================================================
|NO. Size(B) Time Type Name |
|1 4132864 Jan/01/2016 00:00:00 M flash:/wa5300-oasis-boot.bin |
|2 24199168 Jan/01/2016 00:00:00 M flash:/wa5300-oasis-system.bin |
============================================================================
果然升级文件保存在flash里了，M标记是主文件
===============================<File CONTROL>===============================
|Note:the operating device is flash |
|<1> Display All File(s) |
|<2> Set Image File type |
|<3> Set Bin File type |
|<4> Set Configuration File type |
|<5> Delete File |
|<0> Exit To Main Menu |
============================================================================
Enter your choice(0-5):0返回上级
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9):按下Ctrl+Y查看一下AP模式
Please select the new mode
Current mode is Oasis Mode当前是Oasis模式
============================================================================
|NO. Mode |
|1 Fat Mode |
|2 Fit Mode |
|3 Anchor-AC (Virtual AC Mode) |
|4 Anchor-Fit |
|5 Oasis Mode |
|0 Exit |
============================================================================
Enter your choice(0-5):1可以看到这个菜单也与之前不一样了，试着切换为Fat模式
Not Support!不支持，新版本的软件，其实Oasis就是Fat
==========================<EXTENDED-BOOTWARE MENU>==========================
|<1> Boot System |
|<2> Enter Serial SubMenu |
|<3> Enter Ethernet SubMenu |
|<4> File Control |
|<5> Restore to Factory Default Configuration |
|<6> Skip Current System Configuration |
|<7> BootWare Operation Menu |
|<8> Skip Authentication for Console Login |
|<9> Storage Device Operation |
|<0> Reboot |
============================================================================
Ctrl+Z: Access EXTENDED ASSISTANT MENU
Ctrl+F: Format File System
Ctrl+C: Display Copyright
Ctrl+Y: Change AP Mode
Enter your choice(0-9):0重新启动
System is starting...
Press Ctrl+D to access BASIC-BOOTWARE MENU
Booting Normal Extended BootWare
The Extended BootWare is self-decompressing.................................
............Done.
****************************************************************************
* *
* H3C WAP722S-W2 BootWare, Version 7.22 *
* *
****************************************************************************
Copyright (c) 2004-2020 New H3C Technologies Co., Ltd.
Compiled Date : Apr 16 2020
CPU Type : ARM
CPU L1 Cache : 32KB
CPU L2 Cache : 256KB
CPU Clock Speed : 710MHz
Memory Type : DDR3 SDRAM
Memory Size : 256MB
Memory Speed : 533MHz
Flash Size : 32MB
PCB Version : Ver.B
BootWare Validating...
Press Ctrl+B to access EXTENDED-BOOTWARE MENU...
Loading the main image files...
Loading file flash:/wa5300-oasis-system.bin.................................
............................................................................
............................................................................
......Done.
Loading file flash:/wa5300-oasis-boot.bin...................................
.Done.
Image file flash:/wa5300-oasis-boot.bin is self-decompressing...............
............................................................................
............................................................................
............................................................................
............................................................................
...............................Done.
System image is starting...
Startup configuration file doesn't exist or is invalid.
Line con0 is available.
Press ENTER to get started.
<H3C>%Sep 3 15:34:03:895 2020 H3C SHELL/5/SHELL_LOGIN: Console logged in from con0.
<H3C>启动成功了，说明我们已经升级成功了
接下来这个AP就可以通过web访问了，当然你也可以继续通过putty进行配置。
（以下这段转自网文）
云AP是Fat AP。初次使用云AP，给云AP上电后，云AP会默认开启4个无线服务：其中一个称之为管理WIFI，也称内部WIFI，SSID为H3C_XXXXXX，XXXXXX为设备mac地址后六位。管理WIFI供商铺内部员工管理使用，一般在2.4G频段工作，当设备未连接到绿洲时，通过连接管理WIFI在浏览器输入10.40.94.1或myap.h3c.com访问本地web页面可进行本设备下的无线服务管理配置，一旦连接上绿洲，将只能通过绿洲平台进行统一的无线服务配置管理。其余3个称为用户WIFI，也称商业WIFI，SSID为H3C_WiFi_1、H3C_WiFi_2、H3C_WiFi_3，不加密，不认证，不隐藏。当设备连接到外网，可为已经连接上用户WIFI的用户提供上网服务。
那么我们连上H3C_XXXXXX，打开浏览器，输入10.40.94.1或myap.h3c.com，用户名：admin密码：h3capadmin，你会看到功能之丰富，现在你可以体验企业级的路由器了！如果你有两个这种AP，那么可以尝试把它们桥接起来，房子再大也不怕！
本人优快云（ID：walkerjie）提供相关升级文件、《版本说明书》、《云AP Web配置指导》、《云AP绿洲平台Web配置指导》、《WLAN配置指导-WDS配置》，欢迎下载
扫一扫
1376
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
