Not to Be Taken Out

Not to Be Taken Out

Mark Twain once went to borrow a certain book from a neighbour in Tarry town. "May I borrow a book from you?" he asked politely."Yes,you're more than welcome to it," the neighbour told him. "But I must ask you to read it here. You know I make a rule never to let any book go out of my library." Some days later the neighbour wished to borrow Twain's machine for cutting grass in the garden. "Why,certainly," Twain told him,"You're more than welcome to it. But I must ask you to use it here. You know that I make it a rule never to let it go out of my garden."

概不外借

在特里镇,马克.吐温有一次去一位邻居那儿借本书。“我可以向您借本书吗?”他礼貌地问道。“当然,非常乐意,”邻居告诉他,“但我要求你在这儿读。你知道我有一条规定,那就是决不让一本书拿出我的图书室。 ” 几天后,这位邻人想从吐温那儿借台割草机。“噢,当然,”吐温告诉他,“非常乐意借给你。但我要你在这儿用。你知道我从来不允许它拿出我的花园。”

What Is CLI Configuration? CLI configuration is essentially to send configurations to devices through command lines. It is a supplementary means of GUI configuration. CLI configuration may conflict with GUI configuration. If you need to use CLI configuration, please read the precautions, Omada Controller User Guide, Help and FAQ carefully. You can contact TP-Link technical support if necessary. General Precautions 1. The GUI and CLI configuration should be planned globally according to the network topology and requirements. 2. To avoid conflicts, it is recommended not to use the CLI to configure the existing functions of the GUI. a. When adopting a new device, the Controller will deliver configurations to the device in the order of GUI, Site CLI, and then Device CLI. If there is a configuration conflict, the configuration delivered last takes effect. b. CLI profiles (including Site CLI profiles and Device CLI profiles) will only be sent to devices once after applied, unless the "Apply Again" button in the Configuration Result is clicked to trigger the full configurations application. c. When a device upgrades its firmware, the Controller will deliver the full configurations to the device in the order of GUI, Site CLI, and then Device CLI. d. Since the later configuration may overwrite the previous configuration, the running configurations of different devices may be different after the same function has been modified repeatedly through GUI, Site CLI and Device CLI. 3. The Omada Controller will not verify the existing GUI and CLI configurations of devices. Be sure to check the existing configurations before performing new configurations. Otherwise, unexpected results may occur after the configurations are delivered, and the devices may even go offline. 4. To avoid configuration conflicts, if you really need to use the CLI to configure a certain function, it is recommended not to configure it through the GUI at the same time. 5. To avoid disconnection of devices from the Controller due to configuration errors or conflicts, it is recommended to configure VLAN, VLAN Interface, IP Address, ACL, etc. via the GUI, and avoid modifying related configurations via the CLI. Repeated Configurations When the same function is configured through the CLI multiple times, the previous configuration may be overwritten, and the last configuration shall prevail. a. It is recommended to confirm the currently effective commands via the CLI configuration viewing function "Show Running Config". b. If you need to cancel a certain configuration, you can enter "no" command. c. If you need to modify a certain configuration, you can enter a new command to overwrite the configuration. d. Apply the final configuration to send the configuration, and confirm that the function is configured correctly and takes effect via the CLI configuration viewing function. Execution Failures If a command configured by the CLI fails to be executed, an error will be reported and subsequent commands will be executed. You can view the error details via the error message, and the command that has been successfully executed before will not be undone. It is recommended to follow the steps below: a. Use the CLI configuration viewing function (Show Running Config) to confirm the commands that have taken effect. If you need to cancel them, you can enter "no" commands and send them to devices. b. Troubleshoot and correct the command error, regenerate the CLI configuration, and deliver it to the device. Command Modification If you need to modify the commands issued through the CLI, please follow the steps below: a. Use the CLI configuration view function (Show Running Config) to confirm the commands that have taken effect, and sort out the commands that need to be canceled. b. Enter "no" commands to cancel the configurations, and send them to devices. Prohibited Commands 1. CLI commands such as modifying user name and password, managing VLAN, SDM profile, reboot, reset, upgrade, import and export configurations have been blacklisted. When using other CLI commands, please also pay attention to avoid affecting the management of the Controller. 2. Device CLI supports the variable function. Although the variable content does not have too many restrictions, for example, you can enter CLI commands, but it is not recommended to use it in this way. 翻译下使用方法
11-29
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值