A10开机

HELLO! BOOT0 is starting!
boot0 version : 1.5.0
dram size =1024
Succeed in opening nand flash.
Succeed in reading Boot1 file head.
The size of Boot1 is 0x0005c000.
The file stored in 0X00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[       0.175] boot1 version : 1.5.1
[       0.175] pmu type = 3
[       0.177] bat vol = 1
[       0.208] axi:ahb:apb=3:2:2
[       0.208] set dcdc2=1400, clock=1008 successed
[       0.210] key
[       0.223] no key found
[       0.223] flash init start
[       1.498] flash init finish
[       1.499] fs init ok
[       1.500] fattype FAT16
[       1.500] fs mount ok
[       1.506] script finish
[       1.507] power finish
[       1.508] storage_type=0
[       1.518] BootMain start
[       1.518] 0
[       1.527] usbdc_vol = 4000, usbdc_cur = 0
[       1.527] usbpc_vol = 4000, usbpc_cur = 0
[       1.530] init to usb pc
[       1.533] set pc
[       1.621] power_start=0x00000002
[       1.621] power trigger
[       1.621] startup status = 0
[       1.624] power start detect
[       1.627] power enter detect
[       1.633] usb start detect
[       1.634] usb enter detect
[       1.637] USB Device!!
[       1.671] LCD SPI doesn't use.
[       2.037] set dc
[       3.723] no battery exist
[       3.723] power exit detect
[       3.723] usb exit detect
[       3.726] key value = 0
[       3.729] recovery key high 100, low 4
[       3.733] unable to find fastboot_key key_max value
[       3.739] test for multi os boot with display
[       3.801] show pic finish
[       3.801] load kernel start
[       3.818] load kernel successed
[       3.818] start address = 0x4a000000
[       3.819] power exit detect
[       3.82

U-Boot 2011.09-rc1-00001-g3251b97-dirty (Dec 28 2012 - 14:01:19) Allwinner Technology

CPU:   SUNXI Family
Board: A10-EVB
DRAM:  512 MiB
NAND:  3800 MiB
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:10-
-name-        -start-       -size-     
bootloader  : 1000000       1000000    
env         : 2000000       1000000    
boot        : 3000000       2000000    
system      : 5000000       20000000   
data        : 25000000      4b000000   
misc        : 70000000      1000000    
recovery    : 71000000      2000000    
cache       : 73000000      14000000   
databk      : 87000000      10000000   
UDISK       : 97000000      56800000   
-----------------------------------
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x3000000, size 0x2000000
 33554432 bytes read: OK

Starting kernel ...

 

 

没有nand_flash时

ELLO! BOOT0 is starting!
boot0 version : 1.5.0
dram size =1024
Succeed in opening nand flash.
Succeed in reading Boot1 file head.
The size of Boot1 is 0x0005c000.
The file stored in 0X00000000 of block 2 is perfect.
Check is correct.
Ready to disable icache.
Succeed in loading Boot1.
Jump to Boot1.
[       0.175] boot1 version : 1.5.1
[       0.175] pmu type = 3
[       0.177] bat vol = 1256
[       0.209] axi:ahb:apb=3:2:2
[       0.209] set dcdc2=1400, clock=1008 successed
[       0.211] key
[       1.248] you can unclench the key to update now
[       1.248] key found, jump to fel
[FES]:                                                                                                
[FES]:=================================================================================================
[FES]:=                                                                                               =
[FES]:=                                         EEMMMMMMLL                                            =
[FES]:=                                     ::MMMHOLIGANEE                                            =

[FES]:INFO : ......1........
[FES]:INFO : ......2........
[FES]:INFO : ......3........
[FES]:INFO : ......4........
[FES]:INFO : ......5........
[FES]:INFO : ......6........
[FES]:INFO : ......7........
[FES]:INFO : ......8........
[FES]:INFO : ......9........
[FES]:CONFIG_USB_GADGET_DUALSPEED
[FES]:fes connect to host
[FES]:INFO : ......10.......
[FES]:jump to fes_main
[FES]:INFO: fes_protocol_process start
[FES]:[info]: set address 3
[FES]:write special pipe
[FES]:INFO: fed reg_addr = 0x40118168
[FES]:fed para[0] = 0x40900000
[FES]:fed para[1] = 0x40901000
[FES]:fed para[2] = 0x00000000
[FES]:fed para[3] = 0x00000000
[Fed]:-------------------------------------------------
[Fed]:                Hello, Nand Register            
[Fed]:-------------------------------------------------
[Fed]:"private" part NOT configured.
NHW : start nand scan
[NAND] nand driver version: 0x0x00000002, 0x0x00000011, data: 0x20121102
NAND_RequestDMA  ok
NFC Randomizer start.
[SCAN_DBG] Nand flash chip id is:0x0x0000002c 0x0x00000068 0x0x00000004 0x0x00000000 0x0x40107e84 0x0x0000004a
Nand Unique ID of chip 0 is :
0x00000002, 0x0000009f, 0x000000cb, 0x00000000
0x000000f0, 0x00000078, 0x000000c0, 0x00000000
0x000000ff, 0x00000000, 0x000000ff, 0x00000000
0x000000ff, 0x00000000, 0x000000ff, 0x00000000

0x000000fd, 0x00000060, 0x00000034, 0x00000000
0x0000000f, 0x00000087, 0x0000003f, 0x00000000
0x00000000, 0x000000ff, 0x00000000, 0x00000000
0x00000000, 0x000000ff, 0x00000000, 0x00000000

 

[SCAN_DBG] ==============Nand Architecture Parameter==============
[SCAN_DBG]    Nand Chip ID:         0x0x4a04682c 0x0xffffffff
[SCAN_DBG]    Nand Chip Count:      0x0x00000001
[SCAN_DBG]    Nand Chip Connect:    0x0x00000001
[SCAN_DBG]    Nand Rb Connect Mode:      0x0x00000001
[SCAN_DBG]    Sector Count Of Page: 0x0x00000008
[SCAN_DBG]    Page Count Of Block:  0x0x00000100
[SCAN_DBG]    Block Count Of Die:   0x0x00001000
[SCAN_DBG]    Plane Count Of Die:   0x0x00000002
[SCAN_DBG]    Die Count Of Chip:    0x0x00000001
[SCAN_DBG]    Bank Count Of Chip:   0x0x00000001
[SCAN_DBG]    Optional Operation:   0x0x00000208
[SCAN_DBG]    Access Frequence:     0x0x00000028
[SCAN_DBG]    ECC Mode:             0x0x00000002
[SCAN_DBG]    Read Retry Type:      0x0x00000000
[SCAN_DBG]    DDR Type:             0x0x00000000
[SCAN_DBG] =======================================================

[SCAN_DBG] ==============Optional Operaion Parameter==============
[SCAN_DBG]    MultiPlaneReadCmd:      0x0x00000000, 0x0x00000030
[SCAN_DBG]    MultiPlaneWriteCmd:     0x0x00000011, 0x0x00000080
[SCAN_DBG]    MultiPlaneCopyReadCmd:  0x0x00000000, 0x0x00000000, 0x0x00000035
[SCAN_DBG]    MultiPlaneCopyWriteCmd: 0x0x00000085, 0x0x00000011, 0x0x00000080
[SCAN_DBG]    MultiPlaneStatusCmd:    0x0x00000070
[SCAN_DBG]    InterBnk0StatusCmd:     0x0x00000078
[SCAN_DBG]    InterBnk1StatusCmd:     0x0x00000078
[SCAN_DBG]    BadBlockFlagPosition:   0x0x00000001
[SCAN_DBG]    MultiPlaneBlockOffset:  0x0x00000001
[SCAN_DBG] =======================================================
NHW : nand hw scan ok
check nand version start.
Current nand driver version is 0x000000ff 0x00000000 0x00000002 0x00000011
Succeed in getting flash info.
Media version is valid in block 0, version info is 0x000000ff 0x00000000 0x00000002 0x00000011
nand driver version match ok in block 0.
VersionCheck end.
[Fed]:To erase boot0 blocks.
Ready to erase boot blocks.
has cleared the boot blocks.
[Fed]:L266,To erase nand.
Ready to erase chip.
nfb phy init ok.
Succeed in getting flash info.
page size:0x00001000, oob_size: 0x00000010, block size: 0x00000100, bad block position: 0x00000001.
chip_cnt = 0x00000001, chip_connect = 0x00000001, rb_cnt = 0x00000001,  rb_connect = 0x00000001,  good_block_ratio =0x000003b6
erase chip 0
find a all 0x00 block 90
find a all 0x00 block 91
has cleared the chip.
the nand is OK.
Ready to scan bad blocks.
nfb phy init ok.
Succeed in getting flash info.
scan CE 0
find defined bad block in chip 0, block 90.
find defined bad block in chip 0, block 91.
 2 bad blocks in CE 0
cal bad block num is 4
cal good block num is 1003
good block ratio is 950
[Fed]:get the good blk ratio after hwscan : 950
[Fed]:erase=1, hasPrivatePart=0.
[Fed]:nand logic size [0x00000000, 0x0076c000]Sec.
[Fed]:Dram size is 1024MBytes
[Fed]:-------------------------------------------------
[Fed]:               Byebye, Nand Register.           
[Fed]:-------------------------------------------------
[FES]:INFO : run addr = 0x00000000 , type = 1437204482
[FES]:
---------------------------------------------------
[FES]:fes_crc   = 0x0x00000000
[FES]:media_crc = 0x0xf3ee8cc1
[FES]:---------------------------------------------------

[FES]:
---------------------------------------------------
[FES]:fes_crc   = 0x0x00000000
[FES]:media_crc = 0x0x98b6bafd
[FES]:---------------------------------------------------

[FES]:
---------------------------------------------------
[FES]:fes_crc   = 0x0x00000000
[FES]:media_crc = 0x0x61a1f06a
[FES]:---------------------------------------------------

[Fed]:SPARSE packet.
[FES]:BlkSecAddr(0x000db400),DramAddr(0x40300000), len(0x0000c744)
[Fed]:parse SPARSE Start.
[Fed]:parse SPARSE End.
[FES]:
---------------------------------------------------
[FES]:fes_crc   = 0x0x00000000
[FES]:media_crc = 0x0xab8f3420
[FES]:---------------------------------------------------

[FES]:BlkSecAddr(0x004b8000),DramAddr(0x40300000), len(0x00000008)
[FES]:
---------------------------------------------------
[FES]:fes_crc   = 0x0x00000000
[FES]:media_crc = 0x0xab5fc3b2
[FES]:---------------------------------------------------

[Fed]:...To UN-REG FED_NAND....
[FES]:INFO : run addr = 0x401e0414 , type = 1437204481
-------------------------------------------------
                Hello, Update boot1.            
-------------------------------------------------
update_Boot1: addr = 0x40410000, good_block_ratio = 950
get the good blk ratio from hwscan : 960
NB1 : enter phy init
[NAND] nand driver version: 0x0x00000002, 0x0x00000011, data: 0x20121102
NAND_RequestDMA  ok
NFC Randomizer start.
[SCAN_DBG] Nand flash chip id is:0x0x0000002c 0x0x00000068 0x0x00000004 0x0x00000000 0x0x401d7ca4 0x0x0000004a
Nand Unique ID of chip 0 is :
0x00000002, 0x0000009f, 0x000000cb, 0x00000000
0x000000f0, 0x00000078, 0x000000c0, 0x00000000
0x000000ff, 0x00000000, 0x000000ff, 0x00000000
0x000000ff, 0x00000000, 0x000000ff, 0x00000000

0x000000fd, 0x00000060, 0x00000034, 0x00000000
0x0000000f, 0x00000087, 0x0000003f, 0x00000000
0x00000000, 0x000000ff, 0x00000000, 0x00000000
0x00000000, 0x000000ff, 0x00000000, 0x00000000

 

[SCAN_DBG] ==============Nand Architecture Parameter==============
[SCAN_DBG]    Nand Chip ID:         0x0x4a04682c 0x0xffffffff
[SCAN_DBG]    Nand Chip Count:      0x0x00000001
[SCAN_DBG]    Nand Chip Connect:    0x0x00000001
[SCAN_DBG]    Nand Rb Connect Mode:      0x0x00000001
[SCAN_DBG]    Sector Count Of Page: 0x0x00000008
[SCAN_DBG]    Page Count Of Block:  0x0x00000100
[SCAN_DBG]    Block Count Of Die:   0x0x00001000
[SCAN_DBG]    Plane Count Of Die:   0x0x00000002
[SCAN_DBG]    Die Count Of Chip:    0x0x00000001
[SCAN_DBG]    Bank Count Of Chip:   0x0x00000001
[SCAN_DBG]    Optional Operation:   0x0x00000208
[SCAN_DBG]    Access Frequence:     0x0x00000028
[SCAN_DBG]    ECC Mode:             0x0x00000002
[SCAN_DBG]    Read Retry Type:      0x0x00000000
[SCAN_DBG]    DDR Type:             0x0x00000000
[SCAN_DBG] =======================================================

[SCAN_DBG] ==============Optional Operaion Parameter==============
[SCAN_DBG]    MultiPlaneReadCmd:      0x0x00000000, 0x0x00000030
[SCAN_DBG]    MultiPlaneWriteCmd:     0x0x00000011, 0x0x00000080
[SCAN_DBG]    MultiPlaneCopyReadCmd:  0x0x00000000, 0x0x00000000, 0x0x00000035
[SCAN_DBG]    MultiPlaneCopyWriteCmd: 0x0x00000085, 0x0x00000011, 0x0x00000080
[SCAN_DBG]    MultiPlaneStatusCmd:    0x0x00000070
[SCAN_DBG]    InterBnk0StatusCmd:     0x0x00000078
[SCAN_DBG]    InterBnk1StatusCmd:     0x0x00000078
[SCAN_DBG]    BadBlockFlagPosition:   0x0x00000001
[SCAN_DBG]    MultiPlaneBlockOffset:  0x0x00000001
[SCAN_DBG] =======================================================
NB1 : nand phy init ok
boot1 last block 0x0x00000006 .
open nand.
boot1 0x00000002
erasing block 2 succeeded..
Succeed in erasing block 2.
succeed in programming block 2.
boot1 0x00000003
erasing block 3 succeeded..
Succeed in erasing block 3.
succeed in programming block 3.
boot1 0x00000004
erasing block 4 succeeded..
Succeed in erasing block 4.
succeed in programming block 4.
boot1 0x00000005
erasing block 5 succeeded..
Succeed in erasing block 5.
succeed in programming block 5.
boot1 0x00000006
erasing block 6 succeeded..
Succeed in erasing block 6.
succeed in programming block 6.
succeed in burning boot1.
-------------------------------------------------
            Succeed in Updating boot1.          
-------------------------------------------------
[FES]:INFO : run addr = 0x401dfa60 , type = 1437204481
-------------------------------------------------
                Hello, Update boot0.            
-------------------------------------------------
burn boot0 normal mode!
get the good blk ratio from hwscan : 960
NB1 : enter phy init
[NAND] nand driver version: 0x0x00000002, 0x0x00000011, data: 0x20121102
NAND_RequestDMA  ok
NFC Randomizer start.
[SCAN_DBG] Nand flash chip id is:0x0x0000002c 0x0x00000068 0x0x00000004 0x0x00000000 0x0x401d6e60 0x0x0000004a
Nand Unique ID of chip 0 is :
0x00000002, 0x0000009f, 0x000000cb, 0x00000000
0x000000f0, 0x00000078, 0x000000c0, 0x00000000
0x000000ff, 0x00000000, 0x000000ff, 0x00000000
0x000000ff, 0x00000000, 0x000000ff, 0x00000000

0x000000fd, 0x00000060, 0x00000034, 0x00000000
0x0000000f, 0x00000087, 0x0000003f, 0x00000000
0x00000000, 0x000000ff, 0x00000000, 0x00000000
0x00000000, 0x000000ff, 0x00000000, 0x00000000

 

[SCAN_DBG] ==============Nand Architecture Parameter==============
[SCAN_DBG]    Nand Chip ID:         0x0x4a04682c 0x0xffffffff
[SCAN_DBG]    Nand Chip Count:      0x0x00000001
[SCAN_DBG]    Nand Chip Connect:    0x0x00000001
[SCAN_DBG]    Nand Rb Connect Mode:      0x0x00000001
[SCAN_DBG]    Sector Count Of Page: 0x0x00000008
[SCAN_DBG]    Page Count Of Block:  0x0x00000100
[SCAN_DBG]    Block Count Of Die:   0x0x00001000
[SCAN_DBG]    Plane Count Of Die:   0x0x00000002
[SCAN_DBG]    Die Count Of Chip:    0x0x00000001
[SCAN_DBG]    Bank Count Of Chip:   0x0x00000001
[SCAN_DBG]    Optional Operation:   0x0x00000208
[SCAN_DBG]    Access Frequence:     0x0x00000028
[SCAN_DBG]    ECC Mode:             0x0x00000002
[SCAN_DBG]    Read Retry Type:      0x0x00000000
[SCAN_DBG]    DDR Type:             0x0x00000000
[SCAN_DBG] =======================================================

[SCAN_DBG] ==============Optional Operaion Parameter==============
[SCAN_DBG]    MultiPlaneReadCmd:      0x0x00000000, 0x0x00000030
[SCAN_DBG]    MultiPlaneWriteCmd:     0x0x00000011, 0x0x00000080
[SCAN_DBG]    MultiPlaneCopyReadCmd:  0x0x00000000, 0x0x00000000, 0x0x00000035
[SCAN_DBG]    MultiPlaneCopyWriteCmd: 0x0x00000085, 0x0x00000011, 0x0x00000080
[SCAN_DBG]    MultiPlaneStatusCmd:    0x0x00000070
[SCAN_DBG]    InterBnk0StatusCmd:     0x0x00000078
[SCAN_DBG]    InterBnk1StatusCmd:     0x0x00000078
[SCAN_DBG]    BadBlockFlagPosition:   0x0x00000001
[SCAN_DBG]    MultiPlaneBlockOffset:  0x0x00000001
[SCAN_DBG] =======================================================
NB1 : nand phy init ok
open nand.
boot0 0x00000000
boot0 0x00000001
-------------------------------------------------
            Succeed in Updating boot0.          
-------------------------------------------------