盈鹏飞嵌入式T113-S4主板_Tina5.0(openwrt)启动信息

最新推荐文章于 2024-12-10 15:26:40 发布

原创

最新推荐文章于 2024-12-10 15:26:40 发布 · 1.8k 阅读

1 ·

CC 4.0 BY-SA版权

文章标签：

#开发语言 #linux

SBC-T113S产品特性：

采用Allwinner公司Cortex-A7双核T113-S3/S4处理器，运行最高速度为1.2GHZ；
内置64-bit XuanTie C906 RISC-V协处理器(仅T113-S4支持)；
支持JPEG/MJPEG视频编码，最大分辨率1080p@60fps；支持多格式1080P@60fps视频解码 (H.265,H.264, MPEG-1/2/4)；
支持RGB666/LVDS/MIPI-DSI，分辨率最高1920x1080；
支持128-256M Bytes DDR3 SDRAM,其中T113-S3内置128MB;T113-S4内置256MB；
支持SPI NAND存储和启动(默认：256MB)或者EMMC启动(默认：4GB,最大32GB)；
支持一路USB2.0 OTG(设计为TYPE-A接口)；支持二路USB2.0 HOST;
支持七路RS232通信或者6路RS232和1路RS485(非隔离)；
支持一路CAN BUS通信（非隔离）；
支持一路10/100M以太网；
稳定的操作系统的支持，可预装LINUX 5.4（Preempt）或者OpenWRT；
经典尺寸主板，尺寸为120*100MM；

SBC-T113S产品功能评估图：

[160]BOOT0 commit : 069ed30b88
[163]set pll start
[165]fix vccio detect value:0xc0
[172]periph0 has been enabled
[175]set pll end
[177][pmu]: bus read error
[179]board init ok
[181]enable_jtag
[183]get_pmu_exist() = -1
[185]DRAM BOOT DRIVE INFO: V0.34
[188]DRAM CLK = 792 MHz
[191]DRAM Type = 3 (2:DDR2,3:DDR3)
[194]DRAMC ZQ value: 0x7b7bfb
[197]DRAM ODT value: 0x42.
[199]ddr_efuse_type: 0x0
[202]DRAM SIZE = 256 MB
[210]DRAM simple test OK.
[212]rtc standby flag is 0x0, super standby flag is 0x0
[217]dram size =256
[220]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 32
[225]block from 8 to 32
[361]Check is correct. Find a good uboot copy at block 8
[366]dma 0x2b3c4 int is not used yet
[369]dma 0x2b3c4 int is free, you do not need to free it again
[375]Entry_name        = u-boot
[382]Entry_name        = optee
[386]Entry_name        = dtb
[389]Jump to second Boot.
M/TC: OP-TEE version: 2a99a16f (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05)) #1 Thu Aug 17 11:13:02 UTC 2023 arm
E/TC:0 0 platform_standby_fdt_parse:126 no pmu0 node
E/TC:0 0 sunxi_twi_parse_from_dt:121 no pmu node


U-Boot 2018.07-g6047f84 (Dec 28 2023 - 04:52:57 +0000) Allwinner Technology

[00.460]CPU:   Allwinner Family
[00.462]Model: sun8iw20
I2C:   FDT ERROR:fdt_set_all_pin:[twi0]-->FDT_ERR_BADPATH
ready
[00.475]DRAM:  256 MiB
[00.478]Relocation Offset is: 0ceb9000
[00.506]secure enable bit: 0
E/TC:0   fdt_getprop_u32:336 prop trace_level not found
[00.520]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=300Mhz
[00.526]gic: sec monitor mode
[00.529]line:703 init_clocks
[00.532]flash init start
[00.534]workmode = 0,storage type = 0
[00.541]sunxi-spinand-phy: spinand sample_mode:2 sample_delay:3

device nand0 <nand>, # parts = 4
 #: name                size            offset          mask_flags
 0: boot0               0x00100000      0x00000000      1
 1: uboot               0x00300000      0x00100000      1
 2: secure_storage      0x00100000      0x00400000      1
 3: sys                 0x0fb00000      0x00500000      0

active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000

defaults:
mtdids  : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.696]ubi0: attaching mtd4
[01.123]ubi0: scanning is finished
[01.133]ubi0: attached mtd4 (name "sys", size 251 MiB)
[01.137]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[01.144]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[01.150]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[01.156]ubi0: good PEBs: 1004, bad PEBs: 0, corrupted PEBs: 0
[01.162]ubi0: user volume: 10, internal volumes: 1, max. volumes count: 128
[01.168]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[01.176]ubi0: available PEBs: 0, total reserved PEBs: 1004, PEBs reserved for bad PEB handling: 40
[01.185]sunxi flash init ok
[01.187]drv_disp_init
partno erro : can't find partition bootloader
** Unable to read file lcd_compatible_index.txt **
[01.455]disp_fat_load for lcd config failed
[01.480]drv_disp_init finish
[01.692]Loading Environment from SUNXI_FLASH... OK
[01.727]boot_gui_init:start
partno erro : can't find partition Reserve0
bad fb1_cfg[w=0,h=0,bpp=32,format=0]
[01.763]boot_gui_init:finish
partno erro : can't find partition bootloader
[01.791]bmp_name=bootlogo.bmp size 38454
[01.802]Item0 (Map) magic is bad
secure storage read widevine fail
secure storage read ec_key fail
secure storage read ec_cert1 fail
secure storage read ec_cert2 fail
secure storage read ec_cert3 fail
secure storage read rsa_key fail
secure storage read rsa_cert1 fail
secure storage read rsa_cert2 fail
secure storage read rsa_cert3 fail
[01.832]usb burn from boot
delay time 0
weak:otg_phy_config
[01.843]usb prepare ok
[01.941]LCD open finish
[02.146]overtime
[02.149]do_burn_from_boot usb : no usb exist
List file under ULI/factory
** Unrecognized filesystem type **
[02.180]update bootcmd
[02.209]change working_fdt 0x4c878e68 to 0x4c858e68
partno erro : can't find partition bootloader
** Unable to read file lcd_compatible_index.txt **
[02.264]disp_fat_load for lcd config failed
partno erro : can't find partition bootloader
writing lcd_compatible_index.txt
[02.296]offset should be 0 but 0xa1 when write to new volume boot-resource
Error: writing contents

** Unable to write "lcd_compatible_index.txt" from sunxi_flash 0:1 **
[02.311]do_fat_fswrite for lcd config failed
partno erro : can't find partition bootloader
** Unable to read file lcd_compatible_index.txt **
[02.345]disp_fat_load for lcd config failed
[02.350]update dts
Info: gmac phy mode = rgmii, phy_interface = 7
Error: gmac get phy-clk-type failed
[02.359]Board Net Initialization Failed
[02.363]No ethernet found.
Hit any key to stop autoboot:  0
boot  addr 0x45000000 0x461d6000 exceed dsp0 scope
dsp0  addr 0x45000000 0x45100000
[04.379]no vendor_boot partition is found
Android's image name: sun8i_arm
The loading address of the kernel is not in the boot image
   Loading Ramdisk to 4c2df000, end 4c854232 ... OK
ERROR: reserving fdt memory region failed (addr=41b00000 size=100000)
ERROR: reserving fdt memory region failed (addr=4c917000 size=300000)
[04.476]Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.61 (ping@embedall) (arm-linux-gnueabi-gcc (Linaro GCC 5.3-2016.05) 5.3.1 20160412, GNU ld (Linaro_Binutils-2016.05) 2.25.0 Linaro 2016_02) #1 SMP PREEMPT Wed Sep 4 19:09:29 CST 2024
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: sun8iw20
[    0.000000] printk: bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 8 MiB at 0x4f800000
[    0.000000] On node 0 totalpages: 65536
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 15 pages/cpu s31040 r8192 d22208 u61440
[    0.000000] pcpu-alloc: s31040 r8192 d22208 u61440 alloc=15*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: ubi.mtd=sys ubi.block=0,rootfs earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyAS0,115200 loglevel=8 root=/dev/ubiblock0_5 rootfstype=squashfs init=/sbin/init partitions=mbr@ubi0_0:boot-resource@ubi0_1:env@ubi0_2:env-redund@ubi0_3:boot@ubi0_4:rootfs@ubi0_5:dsp0@ubi0_6:private@ubi0_7:rootfs_data@ubi0_8:UDISK@ubi0_9: cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun8iw20p1 boot_type=5 androidboot.boot_type=5 gpt=1 uboot_message=2018.07-g6047f84(12/28/2023-04:52:57) disp_reserve=3145728,0x4c917000 aw-ubi-spinand.ubootblks=24 androidboot.dramfreq=792 androidboot.dramsize=256 mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys) uboot_backup=ubootA
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 223588K/262144K available (7168K kernel code, 359K rwdata, 2636K rodata, 1024K init, 199K bss, 30364K reserved, 8192K cma-reserved, 0K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] random: get_random_bytes called from start_kernel+0x250/0x3d0 with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.008008] Switching to timer-based delay loop, resolution 41ns
[    0.014184] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idl

最低0.47元/天解锁文章