Beverage wastewater to single cell proteinR

能源管理基于MATLAB的企业最大需量预测模型:月内峰值追踪与超限风险模拟分析系统设计 项目介绍 MATLAB 企业最大需量预测|月内峰值追踪与超限场景模拟 内容概要:本文介绍了一个基于MATLAB R2025b的企业最大需量预测项目,旨在通过构建月内峰值追踪与超限风险识别模型,实现对企业电力负荷的精细化管理。项目综合考虑时间周期、环境温度、生产强度、特殊日期及随机扰动等因素,构建模拟数据集,并采用装袋回归树和岭回归等机器学习模型进行负荷预测。通过滚动峰值追踪机制,系统动态整合历史真实值与未来预测值,生成月内最大需量趋势曲线,并结合预设阈值实现超限预警。同时支持多场景模拟,如增产、高温、设备集中启动等,评估不同工况下的超限风险,为企业错峰生产、储能调度等决策提供量化支持。项目注重实用性与兼容性,输出形式包括可视化图表、风险等级标识和多格式数据文件,适用于能源管理教学、工业负荷研究及智能用电原型开发。; 适合人群:具备一定MATLAB编程基础,从事能源管理、电力系统分析、工业自动化或智能制造领域的科研人员、工程师及高校师生,尤其适合工作1-3年、希望深入理解负荷预测与企业用电成本控制的技术人员。; 使用场景及目标:①实现企业月内最大需量的动态预测与滚动追踪,提前识别超限风险;②通过多因素场景模拟评估不同生产与环境条件下对需量的影响;③为错峰生产、设备启停优化、储能调度等能源管理决策提供数据支撑;④构建可复现、可扩展的负荷预测分析框架,服务于实际电能管理系统开发。; 阅读建议:此资源以模拟数据为基础,重点在于模型架构设计与管理应用逻辑,建议读者结合提供的代码实例,在MATLAB环境中动手复现数据生成、模型训练、峰值追踪与可视化全过程,并尝试调整特征参数或引入真实数据以深化理解。 立即下载

Java Python Beverage wastewater to single cell protein

1. Abstract

Nowadays, there is an increasing need to treat wastewater using microalgae from agriculture, industrial, and municipal areas. There are many conventional techniques such as the application of anaerobic digestion, biofilms, and membrane separation with varying pore dimensions that have already been widely applied and commercialized. This paper analyzes the traditional use of microalgae in wastewater treatment processes, identifying their drawbacks and current limitations while exploring potential solutions. We focus on three microbial protein production processes, each involving different bacteria: Microalgae (MA), Purple Phototrophic Bacteria (PPB), and Aerobic Heterotrophic Bacteria (AHB). The design of reactor systems for these processes is critically evaluated and optimized. In addition, the potential system boundaries and scenarios are designed for treating the beverage wastewater, with the aim of converting the beverage wastewater into the fish feed through the three processes. The carbon emissions from each stage of these processes are assessed using the life cycle analysis (LCA) techniques. The results are compared with each other to highlight differences in environmental impact across various aspects. The LCA examines factors such as feed and effluent flow rates, the use of fish feed alternatives, electricity, and other energy inputs. All findings are benchmarked against official data, adhering to the standards set in Singapore.

2. Background

In 1965, Singapore was partially self-sufficient in food supply with farmlands occupying approximately 25% of land. However, by 2014, farmlands occupied less than 1% of the land in Singapore. Hence, Singapore is reliant on the 160 countries which it imports food from (Ludher, 2016). Although the overall increase of food consumption was minimal, a breakdown of the food consumption across different categories showed that consumption of vegetables, fruits, and proteins (chicken, pork, and eggs) increased significantly while that of rice reduced drastically. This shows that there is a significant demand for protein among people (Boland, 2013). However, traditional methods of obtaining protein, primarily through animal and dairy production, are ultimately unsustainable. Therefore, it is crucial to explore alternative sources to meet the protein needs of both humans and animals.

One promising solution is the production of microbial protein supplements for animal feed from wastewater streams. In modern society, there is an increasing need for efficient treatment of wastewater from industrial, agricultural, and municipal sources. Singapore, in particular, achieves a 100% wastewater treatment rate (Liao, 2021). The procedure not only effectively treats organic wastewater but also converts organic matter into high-value protein products, reducing environmental burdens while providing a cost-effective and sustainable alternative protein source for agriculture and aquaculture. Meanwhile, the novel wastewater treatment method can avoid the drawbacks of traditional ones, such as anaerobic digestion and membrane separation technologies, are often associated with long start-up period, high energy consumption, operational costs, and environmental drawbacks, limiting their potential for large-scale commercialization (Liu, 2004).

3. Introduction and literature review

Currently, microbial protein has huge potential and prospects in wastewater treatment processes and reflects the implementation of renewable waste energy sources well. However, there still exist challenges in wastewater treatment by utilizing microalgae, and lots of applications are not commercially favored.  There are enormous techniques related to treating wastewater effluents using different types of algae and the results show high efficiency in pollutant removal by manipulating the COD values. For instance, the nanofiltration system developed recently for treating the wastewater from the yeast industry can increase COD retention and promote color and electro-conductivity (EC) removal by showing a decrease in permeate flux after long-term operation (Rahimpour, 2014). In the agricultural and livestock domains, it has already been shown that microalgae can promote the treatment of wastewater from food production.

The research of spiller emphasizes the treatment of organic wastewater to single cell protein by using the comprehensive LCA to evaluate the environmental effects of the microbial protein from potato wastewater which is treated as one of the food effluents as the substitution of the conventional soybean meal as one of the examples. In this case, the high-strength potato wastewater is treated under three different microbial conditions which are Aerobic Heterotrophic Bacteria (AHB), Microalgae together with AHB (MaB), and Purple Non-Sulfur Bacteria (PSNB) (Spiller, 2020). Since microalgae can decrease the amount of nutrients in wastewater by lowering the BOD and COD value significantly, it can be applied as a remediation agent although the chemicals and energy costs are relatively high (Udaiyappan, 2017). The entire removal of microalgae after the completion of treatment is necessary for the complete organic content assimilation.

To estimate the overall carbon emission during the single cell protein production process, the LCA mainly focuses on the environmental impact analysis of each stage or defined functional unit, and the schematic approach is designed to evaluate the entire process from raw material extraction, production, distribution, usage and disposal. The target of LCA is to identify the opportunities to reduce the negative environmental impacts during the fish feed production, transportation and anaerobic treatment processes, which can not only contribute to the design of more sustainable fish feed products and provide the comprehensive view of environmental impact of the whole process, but also inform. the regulation and standards for sustainability to provide a sound basis for decisions. For the system boundaries proposed for AHB, PPB and MA digestion processes, all of them are designed for cradle-to-cradle LCA and cradle-to-grave LCA is applied for embranchment of some functional units in which extra landfill process is required since some of the byproducts are not suitable for fish feed or SCP production. There are two commonly used methodological LCA approaches which are consequential LCA and attributional LCA. The latter one focuses on the environmental exchanges and product system description by analysing the data retrospectively [19], which means that it analyses environmental impacts of products that has already exists while the consequential LCA emphasize on the changes in the design of functional units that results in actions or decisions and broader systems effects. The attributional LCA is applied for this project since the system boundaries has already been fixed and the goal is to figure out the direct impact of associated with specific fish products. The system boundary in this design covers the supply chain from beverage wastewater influent to fish feed production and the function unit is defined as 1 tonne of wastewater that treated to obtain fish feed. And the downstream life cycle steps including consumption and waste management are not considered because it is not relevant for decision making. The inventory data can be categorized into energy and wastewater resources input together with byproduct wastes and main fish feed products output.

The aerobic heterotrophic bacteria (AHB) are defined as the bacteria that can utilize oxygen to maintain their metabolism and it can also gain carbon from different organic compounds. The AHB can be mostly found in soil environment since they can form. spores to survive in adverse conditions. The key feather of AHB is that oxygen is the compulsory requirement for their survive and thrive. And organic matter is consumed for energy and carbon since they are not capable of producing their own food. The AHB plays an important role in decomposing the organic material by breaking down the complicated substances into simple compounds such as monomers and oligomers. What’s more, AHB contribute tremendously to the nutrient cycle within ecosystem by assisting the bioremediation of contaminated environments and indirectly improve the soil fertility and contribute the plants health support. Different from AHB, purple phototrophic bacteria (PPB) are the groups of photosynthetic microorganisms that rely on the light as their primary energy source. They can be discovered in low oxygen level conditions includes lakes, ponds, and other aquatic environments. However, the oxygen is not produced as the byproduct through their unique way of metabolism. The bacteriochlorophylls and carotenoids are the two major pigments contained in PPB which can provide the color variance that ranges from brown, red and green etc [20]. And purple is the predominant color that is shown in most of the species. Since PPB do not produce oxygen when capturing light energy, they utilize sulfur, hydrogen sulfide and other organic matters to perform. anoxygenic photosynthesis and such process results in the production of sulfur compounds as byproducts, which is required to be further treated by extra stages. The PPB can be classified into two groups that are purple sulfur bacteria and purple non-sulfur bacteria. The former one applies sulfur as the main electron donor in their metabolism and the latter can utilize a wide range of organic substances so that it can be discovered in less-sulfur rich environments. Besides contributing to the nutrient cycle, the PPB plays a crucial role in sulfur recycling and organic compounds in anoxic conditions. Both PPB and AHB are researched in bioremediation and wastewater treatment by studying their adaptability, photosynthesis process and potential applications.

Microalgae (MA) are a diverse group of photosynthetic microorganisms that encompass various species.  Based on eukaryotic and prokaryotic division, microalgae are further divided into two different groups. Microalgae primarily inhabit aquatic ecosystems but are also found in terrestrial environments and extreme conditions such as saltwater, soil, sand, and snow (Mata et al., 2010). They are essentially unicellular, though some multicellular microalgae also exist, either as free-living individuals, colonies, or in symbiosis with other microorganisms (Radmer, 1996). Depending on the species, their average size ranges from 2 µm to 2 mm, and they have a simple morphology, typically either motile or non-motile. As photosynthetic organisms, microalgae are among the largest contributors to oxygen production, capable of synthesizing half of the oxygen in the atmosphere, which will contribute to the reduction of carbon emission (Metting F.B., 1996). Based on characteristics such as structural features, pigments, composition, and product storage, microalgae are classified into several groups. Currently, between 200,000 to 1 million species of microalgae have been recorded (Trevor et al., 1996)). Among the numerous species, green algae, cyanobacteria, Spirulina, diatoms, and golden algae are the most widely utilized due to their unique characteristics and the high-value compounds they produce. These microalga types are applied extensively in food, biofuel, health, and environmental sectors, driven by their rapid growth rates, high productivity, and adaptability to diverse cultivation conditions. To manufacture single-cell protein (SCP) applications in animal feed industries, green algae are widely used for their high protein content and balanced amino acid profiles. Additionally, green algae can be cultivated in wastewater environments, thus contribute to the waste 0water treatment. During their cultivation, they will absorb excess nitrogen and phosphorus, which reduces water pollution and contributes to bioremediation efforts (Becker, 2007).

4. Aerobic Heterotrophic Bacteria (AHB)

4.1 Functional units and system boundary design

Figure 1. Schematic diagram of system boundary design of the AHB system.

The overall processes of treatment by AHB can be divided into six steps. For the first step all the beverage wastewater streams will be mixed and adjusted into suitable pH by addition of buffers and other substance rich in nitrogen and phosphorus so that its chemical stability is ensured. The mixing process can be supported by continuous stirred tank reactor (CSTR) in series so that the conversion of the unnecessary compound can be higher than single CSTR and the temperature, pressure and retention time of each reactor can be optimized easily. And then design of anaerobic treatment system is the most important step because this is the step where the complex substrate with high molecule weights will be decomposed into monomers or oligomers so that it becomes easier for anaerobic microorganisms to digest and break down in order to produce biogas and other digestates. The key point in the anaerobic treatment is that the oxygen is entirely excluded so that the final yield of desired products is ensured. In this step the high-rate anaerobic treatment facility is selected to enhance the efficiency of anaerobic beverage wastewater treatment process. The advanced technology selected in this system is up-flow anaerobic sludge blanket (UASB) reactor, which increases the contact between beverage wastewater and biomasses promoting the effective treatment process. For UASB reactor the water pass through the system upwards and degraded by anaerobic organisms and combined with the gravity suspends’ settling actions and with the addition of fluctuant and the biogas which is considered as the byproduct that can be used as power sources of electricity generation is collected at the top of system [10]. The sludge is formed as granules in the surface that aggregated by different bacteria. As the flow conditions vary, the selective environment is provided for those microorganisms to aggregate with each other and proliferate to form. dense biofilms. And the heat produced through electricity generation can also be reused to heat the digestion tank. The AHB photobioreactor was chosen in this case and it utilizes sunlight as primary energy sources to support the photosynthesis processes of microorganisms. And extra solar panels are required to be added for the collection of solar energy. Compared with other reactors, the open system photobioreactor has the advantage of simplicity and low maintenance cost. However, it must be exposed to outside environments together with the pond and raceway design. As a result, it is selected to apply the tubular closed system design since the light, temperature and contamination is easier to control. Additionally, the hollow fibre membrane is selected for the nanofiltration of the digestates because it has the advantage of providing large surface area for filtration in compact form. of tubular structures. And it is capable of filtering out the microorganisms and small particles efficiently. What’s more, it can be arranged in buddle so that it can be applied in large scale. However, the fouling and aging problems cannot be ignored for maintaining of sufficient separation performance. The reason why applying nanofiltration is that the general dimension of aerobic heterotrophic bacteria is around 0.5-5 μm and the pore size for general nanofiltration is around 0.5-2 nm and feeding pressure is approximately 10-25 bar [11]. The spray drying that atomizing the feed biomass into fine droplets and then rapidly drying those droplets by using hot air can well-preserved the quality of biomasses and the morphology and size of final digestate powder can be easily controlled during the drying process. But the inaccurate control of temperature will lead to the formation of byproducts and further separation processes are required. And the uniformity of biomass particle sizes can also be one of the challenges to handle. The quality of final dried AHB is heterogenous and some of the undesired products must be handled by direct landfill. The trucks are used for the transportation of dried digestate residue to landfill and fish feed production and the carbon footprint produced is significant. All the functional units in the schematic diagram are compared with the industrial standard to obtain the avoided wastewater treatment load, avoided fish feed and avoided transportation emissions. The goal of this design is to lower the environmental effect and investment that is associated with treating wastewater and make it into the more sustainable approach to water resource management.

4.2 LCA Calculation and discussion of AHB

Table 1. the input parameters and output yield for AHB treatment system

Beverage wastewater COD concentration (mg/L)

Feed flux (L/day)

Effluent flux (L/day)

COD removal efficiency (%)

Sludge (fish feed) production (L/day)

Single cell protein production (g/day)

Total power required (kW)

Growth rate

(gTSS/gCOD)

1698

350.00

314.10

97.62

35.90

0.48

2.4

0.28

The important data of system boundary and functional units design of AHB is selected for LCA calculation path is listed in table 1. Define the avoided wastewater treatment unit as the 1L conversion of wastewater treatment and the detailed LCA calculation path for treating 1 tons of wastewater is shown as follows:

The COD contained in 1 ton of beverage wastewater (approximated the density of water as 1kg/m3) : 1000L × 1698mg/L =1.698*106mg

The amount of COD in feed per day: 350L/day ×1698mg/L = 594300mg/day

Since the removal efficiency is shown as 96.72%, the treated amount of COD is calculated as: 96.72% × 594300mg/day = 574809.96mg/day

The carbon footprint of beverage wastewater treatment can be approximated as the 0.7 kgCO2 eq/m3 of wastewater which represents the average value of former literature studies [12].To deal with the sludge produced during the AHB treatment process, it is found that the specific energy consumption for sludge dewatering can be approximated as 0.026 for influent pumping, 0.032 for primary settling tank and 0.024 for secondary settling tank (CSTR in series), 0.007 for anaerobic treatments, 2.116 for sludge dewatering in the unit of kWh/m3[13] and these energy are all  reflected in the electricity consumption which increases the total power required. And all the final treated sludge are transported for the biological fish feed production. It is discovered from previous literature that the carbon footprint formed during the fish or shrimp feed production is 0.9883 kgCO2eq/kg [14]. Since all the dried biomasses are packed and transported to different industries, the carbon emissions of 16-tonne truck which is 0.05kgCO2eq/tonne·km [15] is taken as the factor to evaluate the environmental impact caused by transportation. Since the AHB is functioning in the photobioreactor in which only the solar energy is applied, the carbon emission can be taken as 0.05kgCO2eq/kWh which is the carbon emission factor of most of solar panels [16]. And the landfilling process can also produce the average carbon emission of 20gCO2eq/kg [15]. Applying all the parameters discovered, the carbon footprint caused by wastewater treatment per day is computed as:

0.7kgCO2eq/m3× (350.00L/day – 314.10L/day) × 0.001m3/L = 0.0252kgCO2eq/day

Combine with the carbon footprint of electricity generation in Singapore which is 0.412kgCO2eq/kWh [17], the extra carbon footprint required for CSTR operation, sludge drying, anaerobic treatment and influent pumping is calculated as:

(0.026kWh/m3 + 0.032kWh/m3 + 0.024kWh/m3 + 0 Beverage wastewater to single cell proteinR .007kWh/m3) × 350.00L/day × 0.001m3/L × 0.412kgCO2eq/kWh + 35.90L/day × 2.116kWh/m3× 0.001m3/L × 0.412kgCO2eq/kWh = 0.044kgCO2eq/day

Assume the sludge is produced in slow settling process, the density can be approximated as 1.038kg/L [18]. The total carbon emission of AHB photobioreactor, fish feed production and lan filling process can be calculated as follows:

For photobioreactor: 2.40kW × × 0.05kgCO2eq/kWh = 80.223kgCO2eq

For fish feed production: 1.038kg/L × 35.90L/day × 0.9883kgCO2eq/kg = 36.828kgCO2eq/day

Above all, assume that the distance required for the transportation of fish feed is 100km, the total carbon footprint produced in the system boundary can be calculated as:

(0.0252kgCO2eq/day + 0.044kgCO2eq/day + 36.828kgCO2eq/day) × + 80.223kgCO2eq + 0.05kgCO2eq/tonne·km × 100km × × 35.90L/day × 1.038kg/L × 0.001tonne/kg = 1113.19kgCO2eq

Table 2. the sum of LCA results of AHB treatment system

Total amount of COD treated per day (mg)

574809.96

The day spent to treat 1 tonne of wastewater

28

Carbon footprint produced in each process (kgCO2eq)

Beverage wastewater treatment

0.702

Influent pumping

0.043

Primary settling tank

0.053

Secondary settling tank

0.040

Anaerobic treatment

0.012

Sludge drying

0.359

AHB photobioreactor operation

80.223

Fish feed production

1025.85

Fish feed transportation

5.19

Total carbon footprint

1113.19

5. Wastewater to Single Cell Protein through Microalgae

5.1 Introduction of Microalgae-based Method

Microalgal-based wastewater treatment has emerged as one of the most promising approaches for both wastewater purification and nutrient recovery (Cai, 2013; Whitton, 2015). This technology has garnered increasing attention due to its high potential value across industrial and commercial sectors. The core of this process is a symbiotic relationship between microalgae and bacteria, which plays a pivotal role in enhancing treatment efficiency. This symbiosis provides protective mechanisms for the microalgae against toxic compounds present in wastewater, allowing them to perform. photosynthesis efficiently. Through this process, microalgae utilize carbon dioxide to produce oxygen, which is subsequently consumed by bacteria within the wastewater. The bacteria, in absorbing this oxygen, initiate the breakdown of organic carbon, nitrogen, and phosphorus compounds in the wastewater. Concurrently, bacterial will release carbon dioxide, inorganic nitrogen, and phosphorus (Oswald, 1957). These byproducts, in turn, serve as essential nutrients for the microalgae, thereby supporting their growth and enabling a sustained photosynthetic cycle.

Through this process, microalgae can effectively reduce nutrient levels in wastewater to extremely low concentrations, as they absorb these nutrients to fuel their growth. This capability not only helps prevent the eutrophication of natural water bodies but also enables treated water to meet rigorous discharge standards, further highlighting the environmental benefits of this symbiotic system. Furthermore, once the microalgae have proliferated, they can be harvested and processed as a valuable biomass. Through bioprocessing or other methodologies, this biomass can be transformed into raw materials for various applications, including the production of single-cell protein, among other bio-products (Clarens, 2010). This dual-purpose approach, which combines wastewater remediation with the generation of commercially valuable bioproducts, underscores the substantial potential of microalgal technology in sustainable wastewater management and resource recovery.

5.2 Functional units and system boundary design

Figure 2. Schematic diagram of system boundary design of the MA system

The process of converting beverage wastewater into fish feed involves a series of carefully controlled stages, each designed to maximize resource recovery and minimize waste. The initial step is the pre-treatment of wastewater, which stabilizes the pH and nutrient levels to ensure optimal conditions for subsequent processing. In this stage, beverage wastewater is treated with buffering agents (NaHCO₃, KH₂PO₄, Na₂CO₃) and nutrient supplements rich in nitrogen and phosphorus (CO(NH₂)₂, NH₄Cl, Phosphate Salts), enhancing its chemical stability. A continuous stirred tank reactor (CSTR) setup in series is used for this purpose, allowing precise control over variables such as temperature, pressure, and retention time. This configuration facilitates more efficient mixing and reaction, converting unwanted compounds and optimizing the wastewater’s readiness for anaerobic digestion.

The anaerobic system is the next stage in the process, where complex organic compounds are decomposed by anaerobic microorganisms into simpler molecules. This breakdown generates biogas, primarily methane (CH₄) and carbon dioxide (CO₂), which are collected as valuable by-products. During the anaerobic digestion process, biogas is generated, primarily composed of methane (CH₄) and carbon dioxide (CO₂). This biogas can be collected and utilized as a renewable energy source, either for direct combustion to produce heat or through biogas engines to generate electricity. This generated energy can support subsequent steps in the process, reducing the reliance on external energy sources and enhancing the overall sustainability of the wastewater treatment system. The CO₂ produced in this stage can be used directed to the microalgae photobioreactor, providing a carbon source to support microalgal photosynthesis. The anaerobic system operates in an oxygen-free environment, utilizing an up-flow anaerobic sludge blanket (UASB) reactor to enhance wastewater and biomass contact. This reactor design promotes effective digestion, allowing wastewater to pass upward, interact with dense microbial biomass, and release biogas at the top.

In the microalgae photobioreactor, the anaerobically treated wastewater, along with CO₂ and air, is utilized to cultivate microalgae through photosynthesis. This closed tubular photobioreactor is chosen for its ability to maintain controlled conditions, such as light, temperature, and contamination levels, which optimize microalgal growth and productivity. The microalgae assimilate CO₂ and other nutrients from the treated wastewater, resulting in high-nutrient biomass that serves as the basis for fish feed production.

After cultivation, the biomass moves to a membrane system, where it is separated into a liquid effluent and a solid component. The effluent, which contains dissolved nutrients, can be recycled within the system. The solid fraction is nutrient-rich and can be further processed into fertilizer, providing an additional sustainable product from the process. A hollow fiber membrane is used in this stage, offering a large surface area for filtration and effectively separating microorganisms and particles from the liquid.

The concentrated microalgae biomass is then subjected to spray drying, a process that removes moisture from the biomass and converts it into a stable dried microalgae (MA) powder. This powder is rich in protein and can be used as a high-quality fish feed. Spray drying involves atomizing the biomass into fine droplets, which are rapidly dried by hot air, preserving the nutritional content of the microalgae. This drying method allows for control over particle size and morphology, ensuring uniformity and ease of handling in downstream applications.

Finally, the transportation stage involves packaging and transporting the dried microalgae powder to fish farms, where it is used as a nutrient-rich feed source. The inclusion of dried microalgae in fish diets supports aquaculture by providing a sustainable, protein-rich alternative to traditional feed ingredients. This entire process exemplifies a closed-loop system, where wastewater is transformed into valuable products such as fish feed and fertilizer, reducing environmental impact and supporting resource-efficient water management.

5.3 Life Cycle Inventory

Pre-treatment Stage: pump1

Inputs: Beverage wastewater, buffering agents (sodium bicarbonate, potassium dihydrogen phosphate), nitrogen and phosphorus supplements (ammonium chloride).

Outputs: Chemically stabilized wastewater, with optimized pH and nutrient levels for microbial treatment.

Anaerobic System: pump2

Inputs: Pre-treated wastewater, electricity (for mixing and temperature control).

Outputs: Methane (CH₄), carbon dioxide (CO₂), dewatered sludge (partially recycled for fertilizer production), and a small amount of discharge water.

Microalgae Photobioreactor: pump3

Inputs: Anaerobically treated wastewater, CO₂, light, air.

Outputs: Nutrient-rich microalgae biomass.

Membrane Filtration System:

Inputs: Microalgae culture, electricity (for pumps and maintaining pressure).

Outputs: Solid and liquid fractions.

Solid: Nutrient-rich residue used as fertilizer.

Liquid: Effluent for discharge or recirculation within the system to reduce water consumption.

Spray Drying:

Inputs: Concentrated microalgae biomass, electricity and heat

Outputs: Dried microalgae powder, water vapor.

Transportation:

Inputs: Fuel.

Outputs: Transportation emissions (CO₂).

5.4 Goal and Scope

Chlorella is rich in protein and essential amino acids, making them ideal candidates for single-cell protein (SCP) production used in food and feed industries. In this part a Life Cycle Assessment (LCA) of using Chlorella sorokiniana will be conducted for single-cell protein (SCP) production from beverage wastewater, focusing on eutrophication potential (EP), global warming potential (GWP), and overall energy consumption. The primary goal of this LCA is to analyze the environmental impact of converting beverage wastewater into fish feed. The functional Unit is defined as the production of 1 kilogram of dried microalgae (MA) powder as fish feed. The stages covered are Wastewater pre-treatment, Anaerobic digestion (UASB reactor), Microalgae cultivation in photobioreactors, Membrane filtration, Spray drying, and Transportation to fish farms.

5.5 GWP Calculation

The Global Warming Potential (GWP) was assessed to quantify the total greenhouse gas emissions resulting from the treatment of 1 liter of beverage wastewater. The GWP calculation includes methane emissions from the anaerobic digestion stage, CO₂ emissions associated with energy use, and CO₂ emissions from transportation.

According to Alexandre’s report, the main parameters of the anaerobic digesters are show in the following table.

Volume of digester

626 m3

Flow Rate

62.6 m3·day−1

Retention time

20.0 days

Organic loading rate

3.23 kg VSS·m−3·day−1

Digestion temperature

35°C

Methane productivity

0.62 m3·kg−1 VSS

Pumping sludge from mixing tank to AD

72 kWh·day−1

Mixing

194 kWh·day−1

In the anaerobic digestion stage, methane (CH₄) is produced as a by-product. Given that the system consists of two reactors with a combined volume of 1252 m³ and an organic loading rate of 3.23 kg VSS/m³/day, the methane production per day can be calculated as follows:

Daily Methane Production= 0.62 m3·kg−1 VSS×3.23 kg VSS·m−3·day−1×626 m3=1253.62 m3 CH₄·day−1. The daily flow rate is 62.6 m3·day−1=62,000 L·day−1, Methane production per liter of wastewater=1253.62 m3/62,000 L·day−1=0.02 m3 ·L−1, The density of methane at 35°C is 0.66 kg·m−3, so the Methane production per liter of wastewater can be converted to 0.02 m3 ·L−1×0.66 kg·m−3=0.0133 kg CH₄·L1.The global warming potential factor of CH₄ is 25, so the CO₂ equivalent per liter=0.0133 kg CH₄·L1×25=0.33kg CO₂-eq/L

Assume the depth of the system is 4 meters, the surface area would be = 626 m³/4 m = 156.5m2. Using the specific power consumption of 10 W/m³ for mixing (from Mendoza et al., 2013), we would calculate the energy demand as: Mixing Energy= 10 W/m³×626 m3=6260W=6.26kW. The retention time is 20 days, so the annual operation days can assume to be 245 days. The total annual mixing energy is 6.26 kW×24 hours×245 days= 36808.8 kWh. The pumping system is assumed to be the same power consumption which is 72 kWh·day−1. So, the total annual pumping energy is 72 kWh·day−1×245 days=17640 kWh. With a daily flow of 62.6 m³ (62,600 liters) over 245 days, the total volume treated annually = 62,600 L·day−1×245 days=15,335,000L. Thus, the energy per liter (FU)= (36808.8kWh+17640 kWh)/15,335,000L=0.0036 kW·L−1. The Sludge Processing Energy is assumed to be 0.2 kWh/L (based on sludge processing requirements). Total energy per functional unit=0.0036+0.2=0.2036kWh·L−1, CO₂ emissions with a conversion factor of 0.300 kg CO₂/kWh=0.2036 kWh/L×0.3 CO₂/kWh=0.062 kg CO₂ /L.

Assume the photobioreactor is used for large scale microalgae process whose energy consumption is about 12kWh, the energy consumption for a photobioreactor is 12.0kW/h × 20h× 0.05kgCO2eq/kWh /500L/h =0.024kgCO2eq/L, and for fish feed production: 1.038kg/L × 35.90L/day × 0.9883kgCO2eq/kg /1000L/day = 0.0368kgCO2eq/L.

The distance of the transportation is assumed for about 20km and the emission factor for transport is about 0.1kg CO₂/ton·km. The CO₂ from Transport per Functional Unit= 1kg×20km×0.1kg CO₂/ton·km=0.002 kg CO₂ /L.The final GWP =0.33kg CO₂ eq/L+0.002 kg CO₂ /L+0.062 kg CO₂ /L+0.024kgCO2eq/day+0.0368kgCO2eq/L =0.4548 kg CO₂-eq /L

5.6 EP Calculation

According to Alexandre’s report the nutrient concentration in the effluent can be summarized as 40 mg/L Nitrogen, 8 mg/L Phosphorus. The emission factors of 1 kg Nitrogen is 0.42 kg PO₄³⁻-eq, the one of 1 kg of phosphorus = 3.06 kg PO₄³⁻-eq. The function unit is 1 liter of beverage wastewater. EP from Nitrogen=40 mg/L×0.42 kg PO₄³⁻-eq=0.0000168 kg PO₄³⁻-eq/L, Ep from Phosphorus=8 mg/L×3.06 kg PO₄³⁻-eq=0.00002448 kg PO₄³⁻-eq/L. Total EP= 0.0000168 kg PO₄³⁻-eq/L+0.00002448 kg PO₄³⁻-eq/L=0.00004128 kg PO₄³⁻-eq/L=41.28 mg PO₄³⁻-eq/L.

The EP of anaerobic digesters=72 kWh·day−1+194 kWh·day−1= 266 kWh·day−1. The EP factor of power produced in Singapore is 45.8 mg PO₄³⁻-eq/L. EP per liter= 266 kWh·day−1×45.8 mg PO₄³⁻-eq/L=12,182.8 mg PO₄³⁻-eq/day, the pumping system =216 kWh/day×45.8 mg PO₄³⁻-eq/kWh. The total EP per liter=0.3526 mg PO₄³⁻-eq/L.

The energy of the photobioreactor is 12kWh×20h×45.8 mg PO₄³⁻-eq/kWh /50 L·day=219.84 mg PO₄³⁻-eq/L. The Sludge Processing Energy is assumed to be 0.2 kWh/L×45.8 mg PO₄³⁻-eq/kWh=9.16 mg PO₄³⁻-eq/L.

The distance of transportation is assumed at 10 km, the EP= 2.4 mg PO₄³⁻-eq/ton-km ×10km=24 mg PO₄³⁻-eq/L.

The total EP=-41.28 mg PO₄³⁻-eq/L+0.3526 mg PO₄³⁻-eq/L+219.84 mg PO₄³⁻-eq/L+9.16 mg PO₄³⁻-eq/L+24 mg PO₄³⁻-eq/L=212         

Matlab实现使用遗传算法的混合能源系统优化.rar 立即下载

相关推荐

压液氧(LOX)火箭发动机涡轮泵级建立了一条自动化的基于模型的系统工程(MBSE)与多学科设计优化(MDO)流水线.rar

压液氧(LOX)火箭发动机涡轮泵级建立了一条自动化的基于模型的系统工程(MBSE)与多学科设计优化(MDO)流水线.rar

【FDE知识库】(1):AI 编程时代开发语言选型分析,云使用go,企业用java,算法python,底层c

AI 编程时代,开发语言选型需综合考量AI适配度、编译速度、跨平台与学习成本。Python以海量语料和即时执行成首选,适用于AI/ML与原型开发;TypeScript凭借类型系统与秒级构建,成为前端及应用层主流;Go以极速编译与统一风格,契合AI代理高效迭代需求。Rust/C++虽性能强,但编译慢、学习成本高,不适于快速试错。综合推荐:优先选Python、TypeScript、Go,兼顾效率与生态,实现最优AI协作体验。

freewebsys的专栏 658

在加性高斯白噪声和瑞利衰落信道上,针对BPSK_QPSK的误码率性能的MATLAB仿真,并扩展了相位优化的可重构智能表面辅助链路对比.rar

在加性高斯白噪声和瑞利衰落信道上,针对BPSK_QPSK的误码率性能的MATLAB仿真,并扩展了相位优化的可重构智能表面辅助链路对比.rar

DXF、DWG工程制图文件查看器

DXF、DWG工程制图文件查看器。 可以在界面中进行测量(包括距离、面积、角度等等) 无需版权,放心使用。

python 操作海康威视工业相机资源例子--ParametrizeCamera_LoadAndSave.zip

python 操作海康威视工业相机资源例子--ParametrizeCamera_LoadAndSave

数字农业与乡村振兴行业可信数据空间应用规划方案(专项申报版).pptx

数字农业与乡村振兴行业可信数据空间应用规划方案(专项申报版).pptx

含分布式电源的配电网可靠性评估研究(Matlab代码实现)

内容概要:本文围绕含分布式电源的配电网可靠性评估展开研究,基于Matlab代码实现相应的评估模型。研究内容涵盖分布式电源接入对配电网运行特性的影响,采用序贯蒙特卡洛模拟法等可靠性评估方法,对系统在不同运行场景下的供电可靠性指标进行量化分析。通过构建典型配电网模型,仿真分析分布式电源的位置、容量及出力特性对系统可靠性的影响机制,进而为提升配电网韧性与供电质量提供理论支撑和技术手段。研究不仅关注理论建模,还注重实际仿真流程的可操作性与结果的可视化呈现。; 适合人群:具备电力系统基础知识,从事配电网规划、运行与可靠性分析等相关领域的科研人员及工程技术人员,尤其适合研究生及从事新能源并网研究的1-3年工作经验的专业人员。; 使用场景及目标:①掌握含分布式电源的配电网可靠性评估基本理论与方法;②学习并复现主流可靠性评估算法(如蒙特卡洛模拟)的Matlab编程实现;③分析分布式电源接入对系统可靠性的影响规律,支撑配电网优化规划与运行决策。; 阅读建议:建议读者结合电力系统可靠性教材与本文Matlab代码同步学习,重点关注模型构建逻辑与算法实现细节,动手调试代码以加深对评估流程的理解,并尝试在不同网络结构和电源配置下进行仿真对比分析。

Python 列表、元组、集合实验报告:切片删除陷阱、可哈希判定与保序去重

Python 列表、元组、集合实验报告:切片删除陷阱、可哈希判定与保序去重

具有PWM控制VSC-HVDC链路的IEEE30总线传输系统(Simulink仿真实现)

内容概要:本文详细介绍了在Simulink环境中构建和仿真一个集成PWM控制的电压源换流器型高压直流输电(VSC-HVDC)链路的IEEE30节点电力传输系统的研究工作。该模型聚焦于利用PWM技术实现对VSC的高效、精确控制,以提升电力系统的传输效率、动态响应能力和运行稳定性。研究涵盖了系统整体建模、关键设备参数设计、PWM控制策略的实现、以及在标准IEEE30节点系统上的集成方法。通过一系列仿真测试,包括系统在正常运行、负载突变及故障条件下的动态响应,全面分析了VSC-HVDC链路对改善电网电压稳定性、优化潮流分布和增强系统可靠性的具体作用,充分验证了所提方案的有效性和工程应用价值。; 适合人群:具备电力系统分析、高压直流输电技术基础理论知识及Simulink/MATLAB仿真软件操作能力的高校研究生、科研机构研究人员和电力行业工程师。; 使用场景及目标:①作为教学案例,帮助学生深入理解VSC-HVDC的工作原理、控制策略及其在复杂电网中的集成应用;②为电力系统规划与运行人员提供一种可靠的仿真工具,用于评估新型输电技术对现有电网性能的影响,支持电网升级改造决策;③推动VSC-HVDC技术在远距离大容量输电、新能源并网和智能电网建设等领域的创新应用。; 阅读建议:建议读者在学习过程中,结合电力系统稳态与暂态分析的相关理论,重点关注PWM控制模块和VSC的建模细节,动手复现并调试所提供的Simulink模型,通过改变系统参数和运行工况来观察仿真结果的变化,从而深化对VSC-HVDC系统动态特性的理解。

T03_eVTOL低空经济低空无人机AI识别自动处理图像项目设计方案_决策评审版.pptx

T03_eVTOL低空经济低空无人机AI识别自动处理图像项目设计方案_决策评审版.pptx

基于斜坡补偿的Buck电路峰值电流+电压电流双闭环控制【附说明文档】(Simulink仿真实现)优快云首页发布文章优快云同步助手LLC谐振变换器开环+闭环软启动仿真设计(Simulink

内容概要:本文围绕三电平VIENNA整流器的双闭环控制与中点电位平衡问题展开仿真研究,提出了一种基于上下电容电压差值补偿的中点电位平衡策略。该策略在传统电压电流双闭环PI控制的基础上,引入电容电压差值作为反馈信号,通过SVPWM调制中冗余小矢量的时间分配实现中点电荷的定向调节,从而在不改变主控制结构的前提下有效抑制中点电位偏差。仿真结果表明,该方法不仅确保直流母线电压稳定跟踪800V给定值,还能显著提升上下电容电压的均衡度,同时保持输入电流低谐波水平,验证了控制策略的可行性和有效性。; 适合人群:电力电子、电气自动化及相关专业的研究生、科研人员及工程技术人员,具备一定的MATLAB/Simulink仿真基础和电力电子拓扑知识背景者更佳。; 使用场景及目标:①掌握三电平VIENNA整流器的工作原理与中点电位波动的成因;②理解电压电流双闭环PI控制的设计要点与参数整定原则;③学习基于差值补偿的中点电位平衡控制策略及其与SVPWM的协同机制;④应用于充电桩、航空电源、通信电源等中大功率单向整流场合的控制系统设计与优化。; 阅读建议:建议结合文中提供的仿真模型与参数设置进行动手实践,重点关注中点电位平衡投入前后电容电压波形的变化,对比分析不同工况下的系统动态响应,深入理解控制策略的作用机理。同时可进一步探索在电网不平衡、轻载等复杂工况下的控制性能,以拓展应用场景。

基于变频控制的多相交错LLC谐振变换器闭环仿真(Simulink仿真实现)

内容概要:本文详细介绍了基于变频控制的多相交错LLC谐振变换器的闭环仿真设计,重点阐述了其在Simulink环境下的建模与控制策略。通过多相交错技术有效降低输出纹波电流,提升系统效率与功率密度,并采用变频控制(PFM)实现对谐振变换器输出电压的精确调节。文中构建了完整的闭环控制系统,包含电压外环与电流内环,确保系统在负载变化或输入波动等扰动工况下仍能稳定运行。同时,配套提供了仿真模型、参数设计计算书及参考文献,帮助读者深入理解系统设计流程与关键技术细节,具有较强的工程复现价值。该资源适用于电力电子、新能源变换器等相关领域的仿真研究与教学实践。; 适合人群:具备电力电子基础知识,熟悉Simulink仿真工具,从事电源变换器设计、新能源系统研发或相关专业的研究生及工程技术人员。; 使用场景及目标:①掌握多相交错LLC谐振变换器的工作原理与变频控制机制;②学习并实现基于Simulink的闭环控制系统建模与仿真;③理解谐振参数设计、软开关实现及系统稳定性分析方法;④为科研项目、毕业设计或产品原型开发提供可复用的技术参考与仿真平台。; 阅读建议:建议读者结合提供的仿真模型与计算书,逐步完成系统搭建与参数整定,重点关注变频控制逻辑与闭环响应特性。在仿真过程中,可通过调整负载、输入电压等条件,观察系统的动态响应与稳态性能,加深对多相交错与谐振控制优势的理解。同时推荐参考相关文献,拓展对LLC变换器前沿控制策略的认识。

自适应多机器人编队规划,以包围和跟踪具有运动和可见性约束的目标(Matlab代码实现)

内容概要:本文针对“自适应多机器人编队规划,以包围和跟踪具有运动和可见性约束的目标”开展研究,提出一种基于Matlab的仿真方法,实现多机器人在动态环境中对移动目标的协同包围与持续跟踪。该方法综合考虑了机器人的运动学约束与传感器的视线(visibility)限制,设计了分布式控制策略与自适应编队算法,能够在复杂环境下有效维持编队结构的稳定性和任务执行的鲁棒性。研究详细阐述了系统建模过程、控制律设计原理、编队形成与保持机制,并通过Matlab代码实现了完整的仿真验证,展示了算法在不同动态场景下的适应能力与性能优势; 适合人群:具备机器人学、自动控制理论、多智能体系统等相关基础知识,熟悉Matlab编程语言,从事智能系统、协同控制、路径规划与自主导航等方向的研究生、科研人员及工程技术人员; 使用场景及目标:①应用于安防监控、环境探测、灾害救援等场景中的多机器人目标围捕与跟踪任务;②为多智能体协同控制、分布式编队保持、避障与可见性维护等关键技术提供可复现的算法框架与仿真平台;③辅助高校与科研机构在相关领域的教学演示与科研创新,深化对自适应控制与分布式协同机制的理解; 阅读建议:建议读者结合提供的Matlab代码逐模块分析其实现逻辑,重点关注控制律设计、约束处理与自适应机制部分,可通过调整机器人数量、目标轨迹、传感器参数等进行扩展性实验,以深入掌握多机器人协同系统的动态行为与优化方法。

两路半桥LLC谐振变换器软开关Simulink仿真(模拟谐振参数不同、分裂电容)

内容概要:本文详细介绍了两路半桥LLC谐振变换器软开关的Simulink仿真研究,重点模拟了不同谐振参数及分裂电容对系统性能的影响。通过建立精确的电路模型,分析了软开关实现条件、谐振腔参数变化对电压电流波形、效率及功率传输能力的作用机制,探讨了分裂电容结构在改善均流特性与提升系统稳定性方面的优势。仿真结果有助于深入理解LLC变换器的工作原理与动态响应特性,为高频高效电源设计提供理论支持与优化方向。; 适合人群:电力电子、电气工程及其自动化等相关专业的科研人员、研究生及从事开关电源设计的工程师。; 使用场景及目标:①掌握LLC谐振变换器的基本建模与仿真方法;②研究谐振参数(如谐振电感、电容)对软开关过程的影响规律;③分析分裂电容结构在多路并联变换器中的均流与稳定性作用;④为高频高效DC-DC变换器的设计与优化提供仿真依据和技术参考。; 阅读建议:建议结合Simulink模型逐步操作,关注关键波形的观测点,对比不同参数下的仿真结果,深入理解软开关的实现条件与系统动态特性,同时可进一步拓展至效率分析与热管理设计。

patch_1.23.0.2584_game_No6.android.pak

patch_1.23.0.2584_game_No6.android.pak

状态估计【卡尔曼滤波kalman】UKF、EKF、粒子滤波PF学习与研究(Matlab代码实现)

内容概要:本文系统地研究了无迹卡尔曼滤波(UKF)、扩展卡尔曼滤波(EKF)和粒子滤波(PF)在非线性系统状态估计中的理论基础与实际应用,并结合Matlab代码实现进行了深入剖析。内容涵盖三种滤波算法的核心原理、数学推导及其在轨迹估计等工程问题中的具体实施方法。通过详尽的Matlab编程实例,展示了如何利用这些先进滤波技术解决如目标跟踪、传感器融合等复杂问题,并特别探讨了BP神经网络与EKF结合的优化训练策略以及粒子滤波在提高状态跟踪精度方面的潜力。该资料为希望掌握现代状态估计算法的研究人员和技术爱好者提供了一套完整的理论与实践指南; 适合人群:具备一定编程基础,尤其是熟练使用Matlab工具,且对控制理论、信号处理或相关工程技术领域有初步了解的研发人员和高校学生; 使用场景及目标:① 深入理解UKF、EKF和PF的基本概念及其在非线性动态系统中进行状态变量估计的应用;② 通过Matlab代码实践加深对各滤波器工作机制的理解,能够独立开发相应的算法以应对诸如轨迹预测、多源信息融合等实际挑战;③ 探索将BP神经网络与EKF相结合的新途径,以期提升模型的学习效率和预测准确性; 阅读建议:此资源不仅提供了坚实的理论支撑,还包括丰富的代码示例,建议读者按照文档结构循序渐进地学习,同时动手实现每一个案例,以便更深刻地把握各种滤波技术的关键细节。对于致力于深入研究状态估计领域的专业人士而言,这是一份极具价值的学习材料。

数控基础知识数控加工工序的安排原则

数控基础知识数控加工工序的安排原则

WGCNA加权基因共表达网络分析(1)简介、原理

WGCNA简介 WGCNA(Weighted Gene Co-Expression Network Analysis, 加权基因共表达网络分析),鉴定表达模式相似的基因集合(module),解析基因集合与样品表型之间的联系,绘制基因集合之间的调控网络并鉴定关键调控基因 WGCNA适用于复杂的转录组数据(样本数目较多) 研究不同器官/组织类型和不同阶段的发育调控、生物和非生物胁迫的不同时间响应机制 WGCNA原理 原理概要 1.构建基因共表达网络:先构建基因共表达网络,通常利用两两基因之间的表达模式来计算

qq_44520665的博客 3万+
上一篇: program Python
下一篇: MED5539 Clinical and Research Laboratory Skills
priorityqueue2
博客等级 码龄2年 175粉丝 30原创
评论
成就一亿技术人!
拼手气红包6.0元
还能输入1000个字符
 
 条评论被折叠 查看
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付:10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值