My Cisco IOU Racks:
– from flyxj
Vmware configuration:
I have modified Interface IP to match my local configuration:
This is topology looks like. Totally there are six routers and four switches. Good enough to finish most routing / switching lab.
[email protected]:~/LAB# ifconfig
eth0 Link encap:Ethernet HWaddr 00:0c:29:df:93:07
inet addr:192.168.80.159 Bcast:192.168.80.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fedf:9307/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:52 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:5397 (5.2 KiB) TX bytes:908 (908.0 B)
Interrupt:19 Base address:0x2000
eth1 Link encap:Ethernet HWaddr 00:0c:29:df:93:11
inet addr:10.10.10.160 Bcast:10.10.10.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fedf:9311/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:141 errors:0 dropped:0 overruns:0 frame:0
TX packets:95 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13924 (13.5 KiB) TX bytes:12882 (12.5 KiB)
Interrupt:16 Base address:0x2080
eth2 Link encap:Ethernet HWaddr 00:0c:29:df:93:1b
inet addr:192.168.20.160 Bcast:192.168.20.255 Mask:255.255.255.0
inet6 addr: fe80::20c:29ff:fedf:931b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:44 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4843 (4.7 KiB) TX bytes:468 (468.0 B)
Interrupt:17 Base address:0x2400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2014 (1.9 KiB) TX bytes:2014 (1.9 KiB)
Using Telnet access 10 devices with port from 2001 to 2010. Also IOU3 itself support ssh access.
本文详细介绍了如何配置MyCisco IOU路由器的接口IP,并修改了VMware虚拟环境中的本地配置,包括设置根密码为flyxj.cn,以及通过ifconfig命令修改eth0接口的IP地址为192.168.80.160。文中还展示了最终的网络拓扑,包含了六台路由器和四台交换机,足以完成大多数路由和交换实验室任务。








被折叠的 条评论
为什么被折叠?



