i need to know what is pmic_chip Each PMIC device in the systems is enumerated
* starting with zero. in sa8295p
#ifndef PMGPIO_H
#define PMGPIO_H
/** @file pm_gpio.h
*
* PMIC-GPIO MODULE RELATED DECLARATION
* This file contains functions and variable declarations to support
* the PMIC GPIO module.
*/
/*
* Copyright (c) 2009-2013 Qualcomm Technologies, Inc.
* All Rights Reserved.
* Confidential and Proprietary - Qualcomm Technologies, Inc.
*/
/*===========================================================================
EDIT HISTORY FOR MODULE
This section contains comments describing changes made to the module.
Notice that changes are listed in reverse chronological order.
$Header: //components/rel/plt_core.qxa_qa/1.0/pmic/public/amss/core/pm_gpio.h#1 $
when who what, where, why
-------- --- ----------------------------------------------------------
03/01/13 kt Added pm_dev_gpio_get_peripheral_info API.
07/05/12 hs Updated the interface.
03/01/12 hs Updated the interface.
04/26/11 wra Adding more GPIO enumeration needed from PM8921
02/08/11 hw Merging changes from the PMIC Distributed Driver Arch branch
Added struct pm_gpio_config_type
Added pm_gpio_config() and pm_gpio_set_interrupt_polarity()
08/11/10 wra Removed doxygen quotations. They are causing parsing errors
07/26/10 wra Changed documentation from @example to Examples so Deoxygen
can parse the file
07/09/10 jtn Added API to get GPIO status
07/02/10 wra Changed pm_gpio_perph_index to int
06/23/10 vk Added pm_gpio_set_mux_ctrl()
03/15/10 fpe Removed RPC remoting because the application processor can do this directly
10/20/09 jtn Move init function prototype to pm_device_init_i.h
10/19/09 vk Removed init API
08/01/09 vk Modified gpio_digital_input prototype
05/20/09 vk New file
===========================================================================*/
#include "com_dtypes.h"
#include "pm_err_flags.h"
#include "pm_resources_and_types.h"
/** @addtogroup pm_gpio
@{ */
/**
Following api's can be used to configure GPIO as Input
- To configure the mode of GPIO to Input
pm_gpio_cfg_mode
- To configure Pull Up or Pull Down
pm_gpio_set_cur_src_pull
- To configure input voltage levels for GPIO
pm_gpio_set_voltage_source
- To enable GPIO, since gpio's are not enabled by default
they should be enabled after configuration
pm_gpio_enable
- To get the status of input level high or low
pm_gpio_level_status
Following api's can be used to configure GPIO as Input
- To configure mode of GPIO to output
pm_gpio_cfg_mode
- To configure Output buffer type eg. CMOS, Open Drain High, Open Drain Low
pm_gpio_set_out_buf_cfg
- To configure drive strength of GPIO
pm_gpio_set_out_buf_drv_str
- To configure voltage levels for GPIO
pm_gpio_set_voltage_source
- To drive GPIO level high or low
pm_gpio_set_output_level
- To enable GPIO, since gpio's are not enabled by default
they should be enabled after configuration
pm_gpio_enable
- To check the configuration of output level
pm_gpio_level_status
- To check configuration of various parameters
pm_gpio_reg_status_get
*/
/** Type definition for different GPIOs
*/
typedef enum
{
PM_GPIO_1, /**< GPIO 1. */
PM_GPIO_2, /**< GPIO 2. */
PM_GPIO_3, /**< GPIO 3. */
PM_GPIO_4, /**< GPIO 4. */
PM_GPIO_5, /**< GPIO 5. */
PM_GPIO_6, /**< GPIO 6. */
PM_GPIO_7, /**< GPIO 7. */
PM_GPIO_8, /**< GPIO 8. */
PM_GPIO_9, /**< GPIO 9. */
PM_GPIO_10, /**< GPIO 10. */
PM_GPIO_11, /**< GPIO 11. */
PM_GPIO_12, /**< GPIO 12. */
PM_GPIO_13, /**< GPIO 13. */
PM_GPIO_14, /**< GPIO 14. */
PM_GPIO_15, /**< GPIO 15. */
PM_GPIO_16, /**< GPIO 16. */
PM_GPIO_17, /**< GPIO 17. */
PM_GPIO_18, /**< GPIO 18. */
PM_GPIO_19, /**< GPIO 19. */
PM_GPIO_20, /**< GPIO 20. */
PM_GPIO_21, /**< GPIO 21. */
PM_GPIO_22, /**< GPIO 22. */
PM_GPIO_23, /**< GPIO 23. */
PM_GPIO_24, /**< GPIO 24. */
PM_GPIO_25, /**< GPIO 25. */
PM_GPIO_26, /**< GPIO 26. */
PM_GPIO_27, /**< GPIO 27. */
PM_GPIO_28, /**< GPIO 28. */
PM_GPIO_29, /**< GPIO 29. */
PM_GPIO_30, /**< GPIO 30. */
PM_GPIO_31, /**< GPIO 31. */
PM_GPIO_32, /**< GPIO 32. */
PM_GPIO_33, /**< GPIO 33. */
PM_GPIO_34, /**< GPIO 34. */
PM_GPIO_35, /**< GPIO 35. */
PM_GPIO_36, /**< GPIO 36. */
PM_GPIO_37, /**< GPIO 37. */
PM_GPIO_38, /**< GPIO 38. */
PM_GPIO_39, /**< GPIO 39. */
PM_GPIO_40, /**< GPIO 40. */
PM_GPIO_41, /**< GPIO 41. */
PM_GPIO_42, /**< GPIO 42. */
PM_GPIO_43, /**< GPIO 43. */
PM_GPIO_44 /**< GPIO 44. */
}pm_gpio_perph_index;
/** Select GPIO I/O type
*/
typedef enum
{
PM_GPIO_DIG_IN,
PM_GPIO_DIG_OUT,
PM_GPIO_DIG_IN_DIG_OUT,
PM_GPIO_ANA_PASS_THRU,
PM_GPIO_TYPE_INVALID
} pm_gpio_config_type;
/** Select voltage source.
*/
typedef enum
{
PM_GPIO_VIN0, /**< Voltage input 0. */
PM_GPIO_VIN1, /**< Voltage input 1. */
PM_GPIO_VIN_INVALID
}pm_gpio_volt_src_type;
/** Input/Output level Status.
*/
typedef enum
{
PM_GPIO_LEVEL_LOW, /**< Level of pin is low. */
PM_GPIO_LEVEL_HIGH, /**< Level of pin is high. */
PM_GPIO_LEVEL_INVALID
}pm_gpio_level_type;
/** Select output buffer configuration.
*/
typedef enum
{
PM_GPIO_OUT_BUFFER_CONFIG_CMOS, /**< CMOS output. */
PM_GPIO_OUT_BUFFER_CONFIG_OPEN_DRAIN_NMOS, /**< Open drain NMOS output. */
PM_GPIO_OUT_BUFFER_CONFIG_OPEN_DRAIN_PMOS, /**< Open drain PMOS output. */
PM_GPIO_OUT_BUFFER_CONFIG_INVALID
}pm_gpio_out_buf_cfg_type;
typedef enum
{
PM_GPIO_OUT_BUFFER_RESERVED, /**< Output buffer strength reserved. */
PM_GPIO_OUT_BUFFER_LOW, /**< Output buffer strength low. */
PM_GPIO_OUT_BUFFER_MEDIUM, /**< Output buffer strength medium. */
PM_GPIO_OUT_BUFFER_HIGH, /**< Output buffer strength high. */
PM_GPIO_OUT_BUFFER_INVALID
}pm_gpio_out_buf_drv_str_type;
/** Select current source pulls type.
*/
typedef enum
{
PM_GPIO_I_SRC_PULL_UP_30uA, /**< Pull up 30 uA. */
PM_GPIO_I_SRC_PULL_UP_1_5uA, /**< Pull up 1.5 uA. */
PM_GPIO_I_SRC_PULL_UP_31_5uA, /**< Pull up 31.5 uA. */
PM_GPIO_I_SRC_PULL_UP_1_5uA_PLUS_30uA_BOOST, /**< Pull up 1.5 uA plus 30 uA boost. */
PM_GPIO_I_SRC_PULL_DOWN_10uA, /**< Pull down 10 uA. */
PM_GPIO_I_SRC_PULL_NO_PULL, /**< No pull. */
PM_GPIO_I_SRC_PULL_INVALID
}pm_gpio_i_src_pull_type;
/** GPIO source select.
*/
typedef enum
{
PM_GPIO_SOURCE_GND, /**< Ground. */
PM_GPIO_SOURCE_PAIRED_GPIO, /**< Paired GPIO. */
PM_GPIO_SOURCE_SPECIAL_FUNCTION1, /**< Special function 1. */
PM_GPIO_SOURCE_SPECIAL_FUNCTION2, /**< Special function 2. */
PM_GPIO_SOURCE_SPECIAL_FUNCTION3, /**< Special function 3. */
PM_GPIO_SOURCE_SPECIAL_FUNCTION4, /**< Special function 4. */
PM_GPIO_SOURCE_DTEST1, /**< D-test 1. */
PM_GPIO_SOURCE_DTEST2, /**< D-test 2. */
PM_GPIO_SOURCE_DTEST3, /**< D-test 3. */
PM_GPIO_SOURCE_DTEST4, /**< D-test 4. */
PM_GPIO_SOURCE_INVALID
}pm_gpio_src_cfg_type;
// /** D-test buffer enable/disable.
// */
typedef enum
{
PM_GPIO_DTEST_DISABLE, /**< GPIO D-test disable. */
PM_GPIO_DTEST_ENABLE, /**< GPIO D-test enable. */
PM_GPIO_DTEST_INVALID
}pm_gpio_dtest_buf_en_type;
/** External pin configuration.
*/
typedef enum
{
PM_GPIO_EXT_PIN_DISABLE, /**< Disable EXT_PIN. */
PM_GPIO_EXT_PIN_ENABLE, /**< Puts EXT_PIN at high Z state and disables
// the block. */
PM_GPIO_EXT_PIN_CONFIG_TYPE__INVALID
}pm_gpio_ext_pin_config_type;
/**
* Structure used to return GPIO status. This structure includes all of the
* enums that are used when configuring the GPIOs.
*/
typedef struct
{
boolean enable; /**GPIO Enable Config*/
pm_gpio_config_type mode_select; /**< GPIO mode selection */
pm_gpio_volt_src_type volt_src; /**< GPIO voltage source. */
pm_gpio_out_buf_cfg_type out_buf_cfg; /**< GPIO output buffer configuration. */
pm_gpio_level_type level; /**< GPIO invert EXT_PIN configuration. */
pm_gpio_out_buf_drv_str_type out_buf_drv_str; /**< GPIO output buffer driver strength. */
pm_gpio_i_src_pull_type i_src_pulls; /**< GPIO current source pulls. */
pm_gpio_src_cfg_type src_cfg; /**< GPIO source configuration. */
pm_gpio_dtest_buf_en_type dtest_buffer_on_off; /**< GPIO D-text buffer on/off. */
} pm_gpio_status_type;
/*=========================================================================== */
/* FUNCTION DEFINITIONS */
/*=========================================================================== */
/*=========================================================================== */
/* pm_gpio_enable */
/*=========================================================================== */
/**
* Enables GPIO.
*
* @param[in] pmic_chip Each PMIC device in the system is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure voltage source. See
* #pm_gpio_perph_index.
* @param[in] enable Set TRUE to enable GPIO, FALSE to disable.
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Enable GPIO5:
* @code
* errFlag = pm_gpio_enable(0, PM_GPIO_5, TRUE); @endcode
*/
pm_err_flag_type
pm_gpio_enable(uint8 pmic_chip, pm_gpio_perph_index gpio, boolean enable);
/*=========================================================================== */
/* pm_gpio_cfg_mode */
/*=========================================================================== */
/**
* Set GPIO Configuration to Input, Output, InOut.
*
* @param[in] pmic_chip Each PMIC device in the system is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure voltage source. See
* #pm_gpio_perph_index.
* @param[in] type Configuration type. See pm_gpio_config_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Configure GPIO5 to Output:
* @code
* errFlag = pm_gpio_cfg_in_out(0, PM_GPIO_5, PM_GPIO_DIG_OUT); @endcode
*/
pm_err_flag_type
pm_gpio_cfg_mode(uint8 pmic_chip,
uint8 gpio,
pm_gpio_config_type type);
/*=========================================================================== */
/* pm_gpio_level_status */
/*=========================================================================== */
/**
* Get input level or configuration of output level for a given gpio.
*
* @param[in] pmic_chip Each PMIC device in the system is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure voltage source. See
* #pm_gpio_perph_index.
* @param[in] type Configuration type. See pm_gpio_config_type.
* @param[out] level pointer to level
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Get GPIO5 to Output level:
* @code
* errFlag = pm_gpio_level_status(0, PM_GPIO_5,
* PM_GPIO_DIG_OUT, &level); @endcode
*/
pm_err_flag_type
pm_gpio_level_status(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_config_type type,
pm_gpio_level_type *level_status);
/*=========================================================================== */
/* pm_gpio_set_voltage_source */
/*=========================================================================== */
/**
* Sets the voltage source.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure voltage source. See
* #pm_gpio_perph_index.
* @param[in] voltage_source GPIO voltage source. See
* #pm_gpio_voltage_source_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Set voltage source to VIN2 for GPIO5:
* @code
* errFlag = pm_gpio_set_voltage_source(0, PM_GPIO_5,
* PM_GPIO_VIN2); @endcode
*/
pm_err_flag_type
pm_gpio_set_voltage_source(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_volt_src_type voltage_source);
/*=========================================================================== */
/* pm_gpio_set_out_buf_cfg */
/*=========================================================================== */
/**
* Sets the output buffer configuration.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure the current source pulls. See
* #pm_gpio_perph_index.
* @param[in] out_buffer_config GPIO output buffer configuration: 0 -- CMOS;
* 1 -- open drain. See
* #pm_gpio_out_buf_cfg_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Set the output buffer configuration to CMOS in bias mode for GPIO5:
* @code
* errFlag = pm_gpio_set_out_buf_cfg(0, PM_GPIO_5,
* PM_GPIO_OUT_BUFFER_CONFIG_CMOS); @endcode
*/
pm_err_flag_type
pm_gpio_set_out_buf_cfg(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_out_buf_cfg_type out_buffer_config);
/*=========================================================================== */
/* pm_gpio_set_output_level() */
/*=========================================================================== */
/**
* Sets level for output.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to set the inversion configuration.
* See #pm_gpio_perph_index.
* @param[in] level Output level to be set for GPIO
* see #pm_gpio_output_level_type
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* For GPIO5, set output high:
* @code
* errFlag = pm_gpio_set_output_level(0, PM_GPIO_5,
PM_GPIO_OUTPUT_LEVEL_HIGH); @endcode
*/
pm_err_flag_type
pm_gpio_set_output_level(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_level_type level);
/*=========================================================================== */
/* pm_gpio_set_cur_src_pull */
/*=========================================================================== */
/**
* Sets the current source pulls.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure current source pulls. See
* #pm_gpio_perph_index.
* @param[in] i_source_pulls Current source pulls. See
* #pm_gpio_current_src_pulls_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Set the current source pulls to 1.5 uA + 30 uA boost for GPIO5:
* @code
* errFlag = pm_gpio_set_cur_src_pull(0, PM_GPIO_5,
* PM_GPIO_I_SOURCE_PULL_UP_1_5uA_PLUS_30uA_BOOST); @endcode
*/
pm_err_flag_type
pm_gpio_set_cur_src_pull(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_i_src_pull_type i_src_pull);
/*=========================================================================== */
/* pm_gpio_set_out_buf_drv_str */
/*=========================================================================== */
/**
* Sets the output buffer drive strength.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to configure current source pulls. See
* #pm_gpio_perph_index.
* @param[in] out_buffer_strength GPIO output buffer drive strength.
* #See #pm_gpio_out_buf_drv_str_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* Set the output buffer drive strength for GPIO5 to HIGH:
* @code
* errFlag = pm_gpio_set_out_buf_drv_str(0, PM_GPIO_5,
* PM_GPIO_OUT_BUFFER_HIGH); @endcode
*/
pm_err_flag_type
pm_gpio_set_out_buf_drv_str(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_out_buf_drv_str_type out_buffer_strength);
/*======================================================================= */
/* pm_gpio_set_out_src_cfg */
/*======================================================================= */
/**
* Sets the source configuration.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated
* starting with zero.
* @param[in] gpio GPIO for which to set the source configuration.
* See #pm_gpio_perph_index</td>
* @param[in] source Select the source. See #pm_gpio_src_cfg_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*
* <b>Example </b> \n
* To serve GPIO5 as an output in Level Translator mode, select Pair In as
* the source:
* @code
* errFlag=pm_gpio_set_src_cfg(0, PM_GPIO_5,
* PM_GPIO_SOURCE_PAIRED_GPIO); @endcode
*/
pm_err_flag_type
pm_gpio_set_out_src_cfg(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_gpio_src_cfg_type source);
/*======================================================================= */
/* pm_gpio_irq_enable */
/*======================================================================= */
/**
* @brief This function enables or disables gpio irq
*
* @param[in] pmic_chip. Primary: 0. Secondary: 1
* @param[in] gpio:
* GPIO number. Refer enum pm_gpio_perph_index.
*
* @param[in] enable:
* TRUE: Enable interrupt for the gpio
* FALSE:Disable interrupt for the gpio
*
*
* @return pm_err_flag_type
* PM_ERR_FLAG__FEATURE_NOT_SUPPORTED = Feature not available on this
* version of the PMIC.
* PM_ERR_FLAG__SUCCESS = SUCCESS.
*
*/
pm_err_flag_type
pm_gpio_irq_enable(uint8 pmic_chip,
pm_gpio_perph_index gpio,
boolean enable);
/*======================================================================= */
/* pm_gpio_irq_clear */
/*======================================================================= */
/**
* Clears the GPIO IRQ.
*
* @param[in] pmic_chip Primary -- 0; Secondary -- 1.
* @param[in] gpio GPIO number. See #pm_gpio_perph_index.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_irq_clear(uint8 pmic_chip, pm_gpio_perph_index gpio);
/*======================================================================= */
/* pm_gpio_irq_set_trigger */
/*======================================================================= */
/**
* Configures the GPIO for an IRQ.
*
* @param[in] pmic_chip Primary -- 0; Secondary -- 1.
* @param[in] gpio GPIO number. See #pm_gpio_perph_index.
* @param[in] trigger One of the various IRQ triggers. See
* #pm_irq_trigger_type.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_irq_set_trigger(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_irq_trigger_type trigger);
/*======================================================================= */
/* pm_gpio_irq_status */
/*======================================================================= */
/**
* Gets the GPIO IRQ status.
*
* @param[in] pmic_chip Primary -- 0; Secondary -- 1.
* @param[in] gpio GPIO number. See #pm_gpio_perph_index.
* @param[in] type Type of IRQ status to read. See #pm_irq_status_type.
* @param[out] status IRQ status.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_irq_status(uint8 pmic_chip,
pm_gpio_perph_index gpio,
pm_irq_status_type irq_type,
boolean *status);
/*======================================================================= */
/* pm_gpio_reg_status_get */
/*======================================================================= */
/**
* Returns the status of one of the PMIC GPIOs.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated,
* starting with zero.
* @param[in] gpio GPIO identifier.
* @param[out] gpio_status Pointer to the GPIO status.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_reg_status_get(uint8 pmic_chip, pm_gpio_perph_index gpio,
pm_gpio_status_type *gpio_status);
/*======================================================================= */
/* pm_gpio_get_perph_id */
/*======================================================================= */
/**
* Returns peripheral ID for gpio.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated,
* starting with zero.
* @param[in] gpio GPIO identifier.
* @param[out] addr Pointer to the .
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_get_perph_id(uint8 pmic_chip,
pm_gpio_perph_index gpio,
uint32 *addr);
/*======================================================================= */
/* pm_gpio_create_channel */
/*======================================================================= */
/**
* Associate spmi channel with gpio
* if *chid = -1 , then a new channel id will be created
* if *chid !=-1 , then *chid will be considered a valid existing channel and
* no new channel will be created . The existing *chid will be associated with
* the gpio.
* This way we can use same channel for multiple gpios if needed. However it
* is not required that we use same channel for multiple gpios or vice versa
* To be used with pmic client only.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated,
* starting with zero.
* @param[in] gpio GPIO identifier.
* @param[out] channel id.
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_create_channel(uint8 pmic_chip , pm_gpio_perph_index gpio , int *chid);
/*======================================================================= */
/* pm_gpio_wait_for_irq */
/*======================================================================= */
/**
* Waits for interrupt on gpio. To be used with pmic client only.
*
* @param[in] pmic_chip Each PMIC device in the systems is enumerated,
* starting with zero.
* @param[in] gpio GPIO identifier.
*
* @return
* SUCCESS or Error -- See #pm_err_flag_type.
*/
pm_err_flag_type
pm_gpio_wait_for_irq(uint8 pmic_chip, pm_gpio_perph_index gpio, int chid);
/** @} */ /* end_addtogroup pm_gpio */
#endif /* PMGPIO_H */
最新发布
忙碌日常与技术感悟
作者分享了最近的生活点滴，包括一次广州之行及与朋友们相聚的时光。此外，还记录了自己在技术学习上的进展与反思，特别是对于基础数学课程的重要性有了更深的认识，并计划深入学习LINUX0.11 KERNEL。
扫一扫
1万+
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
