Centos 配置eth0 提示Device does not seem to be present

一.故障现象：

[root@c1node01 ~]# service network restart
Shutting down loopback insterface:                                                       [   OK  ]
Bringing up loopback insterface:                                                            [   OK  ]
Bringing up interface eth0:  Device eth0 does not seem to be present,delaying initialization.                    [FAILED]

解决办法：

[root@c1node01 ~]# rm -rf /etc/udev/rules.d/70-persistent-net.rules
[root@c1node01 ~]# reboot ………………
[root@c1node01 ~]# service network restart
Shutting down loopback insterface:                                                         [   OK   ]
Bringing up loopback insterface:                                                              [   OK   ]
Bringing up interface eth0:                                                                     [   OK   ]
[root@c1node01 ~]#

二.另一种方法
造成这样的原因，是因为在虚拟机（Vmware）中移动了Centos系统对应的文件，导致重新配置时，网卡的MAC地址变了，输入ifconfig -a,找不到eth0
·······

安装完一个centos虚拟机，又拷贝一份，开机后网卡无法正常启动，报错：Device eth0 does not seem to be present,
delaying initialization

 

解决：#

mv /etc/sysconfig/network-scripts/ifcfg-eth0 
sysconfig/network-scripts/ifcfg-eth1

_____________________________________________________________________________________________________________________________

vim sysconfig/network-scripts/ifcfg-eth1

修改DEVICE="eth0" 

为DEVICE="eth1"

然后重启启动网卡尝试下

三.比第一种更深入一点

故障前的操作：

DELL刀片装的是CentOS6.3的操作系统，网卡识别的是em1和em2，由于工作需要做了槽位调整，并启动了刀片

故障现象：

启动后网络不通，通过iDRAC登录后route查看缺省路由正常；

重启网络服务：

 

[root@nodeA ~]# service network restart 

Shutting down loopback insterface: [ OK ] 

Bringing up loopback insterface: [ OK ]

 Bringing up interface em1: Device em1 does not seem to be present,delaying initialization. [FAILED]

分析问题和解决：

之前在别的文章中我们提过70-persistent-net.rules文件，所以看了一下：

[root@nodeA ~]# vi /etc/udev/rules.d/70-persistent-net.rules   # This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single # line, and change only the value of the NAME= key.   # PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1e", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"   # PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"

 

发现NAME的名称不正确，依次将上述红色字体中的eth0改为em1，eth1改为em2；

*切记：网卡编号由MAC地址大小决定，MAC越小网卡编号越小；

如下：

…………   # PCI device 0x14e4:0x163a (bnx2)   SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1e", ATTR{type}=="1", KERNEL=="eth*", NAME="em2"   # PCI device 0x14e4:0x163a (bnx2) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="24:b6:fd:ab:76:1c", ATTR{type}=="1", KERNEL=="eth*", NAME="em1"

 

保存退出~！

 

[root@nodeA ~]#reboot

………………

问题解决~！