本文档详细介绍了Solaris系统的安装过程，包括定义系统名称、网络配置、设置时区及日期时间等步骤。特别强调了如何配置网络接口及是否使用DHCP进行自动配置。
7、出现如下提示：
q Identify This System qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
On the next screens, you must identify this system as networked or
non-networked, and set the default time zone and date/time.
If this system is networked, the software will try to find the information
it needs to identify your system; you will be prompted to supply any
information it cannot find.
> To begin identifying this system, press F2.
qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
F2_Continue F6_Help
该提示告诉安装人员，要开始定义系统的名字，网络及掩码，时区及时间
按Esc-2键继续安装；
- Network Connectivity ---------------------------------------------------------
Specify Yes if the system is connected to the network by one of the Solaris
or vendor network/communication Ethernet cards that are supported on the
Solaris CD. See your hardware documentation for the current list of
supported cards.
Specify No if the system is connected to a network/communication card that
is not supported on the Solaris CD, and follow the instructions listed under
Help.
Networked
---------
[X] Yes
[ ] No
--------------------------------------------------------------------------------
Esc-2_Continue Esc-6_Help
安装程序提示系统是否连接了网络？使用上下箭头键移动，在合适的位置停止后，按空格键， 选中该选项；在我们的安装中，需要网络功能，因此按Esc-2键继续安装；
- Configure Multiple Network Interfaces ----------------------------------------
Multiple network interfaces have been detected on this system. Specify all
of the network interfaces you want to configure.
Note: You must choose at least one interface to configure.
Network interfaces
------------------
[X] bge0
[ ] bge1
[ ] bge2
[ ] bge3
--------------------------------------------------------------------------------
Esc-2_Continue Esc-6_Help
选择主网卡接口 在我们的安装例子中，使用上下箭头键移动光标，移动到bge0处，按空格键选中该网卡，，因此按Esc-2键继续安装
- DHCP for bge0 ----------------------------------------------------------------
Specify whether or not this network interface should use DHCP to configure
itself. Choose Yes if DHCP is to be used, or No if the network interface is
to be configured manually.
NOTE: DHCP support will not be enabled, if selected, until after the system
reboots.
Use DHCP for bge0
-----------------
[ ] Yes
[X] No
q Identify This System qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
On the next screens, you must identify this system as networked or
non-networked, and set the default time zone and date/time.
If this system is networked, the software will try to find the information
it needs to identify your system; you will be prompted to supply any
information it cannot find.
> To begin identifying this system, press F2.
qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
F2_Continue F6_Help
该提示告诉安装人员，要开始定义系统的名字，网络及掩码，时区及时间
按Esc-2键继续安装；
- Network Connectivity ---------------------------------------------------------
Specify Yes if the system is connected to the network by one of the Solaris
or vendor network/communication Ethernet cards that are supported on the
Solaris CD. See your hardware documentation for the current list of
supported cards.
Specify No if the system is connected to a network/communication card that
is not supported on the Solaris CD, and follow the instructions listed under
Help.
Networked
---------
[X] Yes
[ ] No
--------------------------------------------------------------------------------
Esc-2_Continue Esc-6_Help
安装程序提示系统是否连接了网络？使用上下箭头键移动，在合适的位置停止后，按空格键， 选中该选项；在我们的安装中，需要网络功能，因此按Esc-2键继续安装；
- Configure Multiple Network Interfaces ----------------------------------------
Multiple network interfaces have been detected on this system. Specify all
of the network interfaces you want to configure.
Note: You must choose at least one interface to configure.
Network interfaces
------------------
[X] bge0
[ ] bge1
[ ] bge2
[ ] bge3
--------------------------------------------------------------------------------
Esc-2_Continue Esc-6_Help
选择主网卡接口 在我们的安装例子中，使用上下箭头键移动光标，移动到bge0处，按空格键选中该网卡，，因此按Esc-2键继续安装
- DHCP for bge0 ----------------------------------------------------------------
Specify whether or not this network interface should use DHCP to configure
itself. Choose Yes if DHCP is to be used, or No if the network interface is
to be configured manually.
NOTE: DHCP support will not be enabled, if selected, until after the system
reboots.
Use DHCP for bge0
-----------------
[ ] Yes
[X] No
扫一扫
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
