OGG-01028 Incompatible Record

本文提供了解决Oracle GoldenGate OGG-01028错误的具体步骤,适用于未损坏的trail文件场景。介绍了如何使用logdump工具定位故障点,并通过调整RBA值来恢复Extract或Replicat进程。

摘要生成于 C知道 ,由 DeepSeek-R1 满血版支持, 前往体验 >

由于rep端异常关机或者rep端的mgr没有正常关机导致的trail文件不完整。

查询mos

How to recover from an OGG-01028 Incompatible Record if the trail is not corrupt (Doc ID 1507462.1)


Oracle GoldenGate - Version 9.5_EA and later
Information in this document applies to any platform.
GOAL

To recover from error: OGG-01028 Incompatible record in /ggtrail/GGODSCF/dirdat/cf000325, rba 19018 (getting header).

when it is known that the trail file is intact.

This applies to both extract data pumps and replicats


FIX

If a trail is not corrupt, a pump or replicat can be restarted by noting the point of failure (trail number and RBA) indicated in the report and discard file. Please do not attempt this if you are not familiar with reading these reports.

This should be done on transaction boundaries or with RESTARTCOLLISIONS enabled. If you do not understand this, do not do this yourself; please have support assist you.



>logdump
logdump> log to mycase.txt
logdump> open (/ggtrail/GGODSCF/dirdat/cf000325) <<<--- the trail in the report
logdump> ghdr on
logdump> pos (RBA 19018) <<<--- the RBA in the report 
logdump> n
this will give you a bad header message

logdump> sfh prev
this gives you the header of the previous record start,write down the RBA value <<<--- If it's the transaction boundary or only DML in transaction

logdump> count
if this finishes Ok and gives you a count of tables and records, the trail is OK and you can use the RBA we saved for the alter later
the trail is known to be undamaged
if this does not finish with the count, you have a bad trail and must use another recovery method, contact support.
logdump> exit

You now have a history of what you did in file mycase.txt and a written record of the RBA to use to ALTER the extract data pump or replicat

ggsci> alter extract xxx, extseqno < the existing sequence number>, extrba 
ggsci> start

实际我敲count后出现“Bad record found at (RBA xxxxxx)”

然后我pos到这个rba 敲n后

一直都是bad record

scanforendtrans

scanforheader 

这两个命令都是bad record ,此时认为后面的记录都坏掉了,将rep进程指到下一个trail文件。


<think>我们正在处理一个无线AP无法上线的问题,用户询问如何使用命令`displayaponline-fail-recordtroubleshooting`来查看上线失败记录。根据之前的对话,我们已经讨论了AP无法上线的排查步骤和常见原因。现在用户希望查看具体的上线失败记录,这是一个非常具体的操作命令。注意:用户提供的引用[1]和[2]似乎与当前问题关联不大,引用[1]是关于VRF中ARP表项的问题,引用[2]是关于丢包的可能原因。因此,我们主要参考之前对话中关于AP无法上线的排查步骤,并针对用户当前的问题进行解答。在华为AC(接入控制器)上,`displayaponline-fail-recordtroubleshooting`命令用于显示AP上线失败的故障排查记录。该命令会输出AP上线失败的原因,帮助管理员快速定位问题。使用步骤:1.登录AC的命令行界面。2.执行命令:`displayaponline-fail-recordtroubleshooting[ap-macap-mac|ap-nameap-name]`可以指定AP的MAC地址或名称,如果不指定,则显示所有AP的上线失败记录。输出解析:命令输出的信息通常包括:-AP的MAC地址和名称-上线失败的原因(例如:认证失败、IP地址冲突、版本不匹配等)-失败时间-建议的解决措施常见失败原因及对应措施(基于之前讨论的常见原因):1.**认证失败**:检查AP的预共享密钥(PSK)或SN码是否与AC配置一致。2.**IP地址冲突**:检查AP获取的IP地址是否与其他设备冲突,确保DHCP服务器分配地址正常。3.**版本不匹配**:AP与AC的软件版本不兼容,需要升级或降级AP/AC的版本。4.**网络不可达**:AP与AC之间的网络连通性问题,检查路由、防火墙、VLAN配置等。5.**License不足**:AC的License数量不足以注册新的AP,需要购买并安装新的License。示例输出(模拟):```APMAC:00e0-fc12-3456APName:AP-1FailureReason:Authenticationfailed.Thepre-sharedkeyisincorrect.Time:2023-10-0514:30:25Suggestion:Checkthepre-sharedkeyconfigurationontheAPandAC.```因此,用户可以通过该命令快速定位到具体AP的上线失败原因,然后根据建议措施进行修复。注意:不同版本的AC可能命令输出略有差异,请以实际设备输出为准。如果命令没有输出记录,说明近期没有AP上线失败,或者该AP没有尝试上线。此时可以检查AP是否已经正常上线,或者检查网络连接是否正常。如果用户需要进一步排查,可以结合之前提供的排查步骤(如检查网络连通性、配置等)进行。相关问题:1.如何使用命令行查看AP的当前状态?2.如何更新AP的软件版本?3.如何检查AC的License使用情况?4.如何配置AP的预共享密钥?5.如何为AP配置正确的VLAN?</think>### 查看AP上线失败记录的方法 在华为/华三等AC设备上,使用 **`display ap online-fail-record troubleshooting`** 命令可查看AP上线失败的详细诊断记录。该命令会输出关键错误原因、时间戳和修复建议,是排查AP无法上线的核心工具。 --- ### **执行步骤与输出解析** 1. **登录AC命令行界面** ```bash <AC> display ap online-fail-record troubleshooting [ap-mac MAC地址 | ap-name AP名称] ``` - 可选参数:指定特定AP(按MAC或名称),不指定则显示所有失败记录。 2. **关键输出字段解析** | 字段 | 说明 | 典型错误示例 | |---------------------|----------------------------------------------------------------------|---------------------------------------| | `AP MAC` | 失败AP的物理地址 | 00e0-fc12-3456 | | `Failure Time` | 失败发生的时间戳 | 2023-10-05 14:30:25 | | `Failure Phase` | 失败阶段(如发现AC、建立隧道、认证等) | CAPWAP Tunnel Establishment Failed | | `Error Code` | 错误代码(直接定位问题类型) | 4303 (AC资源不足) | | `Reason` | **核心字段**:详细失败原因 | DHCP IP conflict / License expired | | `Suggested Action` | 修复建议 | Check DHCP pool / Add AP licenses | 3. **常见错误原因与应对**(基于输出中的`Reason`字段) - **`AC discovery failed`** - 原因:AP无法发现AC的IP地址 - 措施:检查AC的`capwap source-ip`配置,确认AP与AC间路由可达[^1]。 - **`Authentication failure (PSK mismatch)`** - 原因:AP与AC的预共享密钥不匹配 - 措施:在AC上执行`ap-auth-mode mac-auth psk cipher 密钥`同步配置。 - **`Insufficient license resources`** - 原因:AC授权AP数量不足 - 措施:`display license`查看剩余配额,申请新License[^1]。 - **`DHCP IP conflict detected`** - 原因:AP获取的IP与其他设备冲突 - 措施:检查DHCP服务器日志,隔离冲突IP[^2]。 --- ### **高级排查技巧** 1. **结合日志深度分析** 若命令输出信息不足,追加查看AC的详细日志: ```bash <AC> display logbuffer | include "MAC of AP" ``` 2. **抓包验证CAPWAP流程** 当显示`CAPWAP tunnel failed`时,在AP接入的交换机端口抓包: ```wireshark filter: udp.port == 5246 || udp.port == 5247 // CAPWAP控制/数据端口 ``` - 检查Discovery Request/Response报文是否交互正常。 --- ### **典型故障案例** > **输出记录示例** > ``` > AP MAC: 00e0-fc76-8921 > Failure Time: 2023-10-05 10:22:31 > Error Code: 4309 > Reason: AP version incompatible with AC. (AC: V200R019, AP: V200R017) > Suggested Action: Upgrade AP to V200R019 via FTP. > ``` > **解决**:通过`ap-update mode ftp`将AP版本升级至与AC一致。 ---
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值