8139 DOS上网配置文件

最新推荐文章于 2023-04-23 13:58:17 发布

原创最新推荐文章于 2023-04-23 13:58:17 发布 · 2.9k 阅读

1 ·

CC 4.0 BY-SA版权

文章标签：

#dos #microsoft #network #each #file #disk

DOS/Win9x 专栏收录该内容

8 篇文章

订阅专栏

本文档介绍了在REALTEK RTL8139快速PCI适配器上设置Microsoft Network Client for DOS驱动程序的过程，包括驱动位置、示例配置文件，还详细说明了安装步骤，如运行SETUP.EXE、响应屏幕提示、添加适配器等。

摘要生成于 C知道，由 DeepSeek-R1 满血版支持，前往体验 >

REALTEK Help8139 Ver 1.10

               ==========     Start of File     ==========
   Microsoft Network Client 3.0 for MS-DOS

   Introduction:
   -------------
   This document describes the procedure to setup the Microsoft Network
   Client for DOS driver on REALTEK RTL8139 Fast PCI adapter.

   Location of Driver:   /NDIS2DOS/RTSND.DOS

   Sample Configuration Files:
    ---------------------------
     Ex1: [PROTOCOL.INI] (install creates this file)

          [network.setup]
          version=0x3110
          netcard=RTL8139,1,RTL8139,1
          transport=ms$ndishlp,MS$NDISHLP
          transport=ms$netbeui,MS$NETBEUI
          lana0=RTL8139,1,ms$netbeui
          lana1=RTL8139,1,ms$ndishlp

          [protman]
          DriverName=PROTMAN$
          PRIORITY=MS$NDISHLP

          [MS$NDISHLP]
          DriverName=ndishlp$
          BINDINGS=RTL8139

          [MS$NETBEUI]
          DriverName=netbeui$
          SESSIONS=10
          NCBS=12
          BINDINGS=RTL8139
          LANABASE=0

         [RTL8139]
         ; RTL8139 RPOTOCOL.INI SAMPLE
         DriverName=RTSND$
         EtherID=@52544C111111 ;This keyword is used to desinate a RTL8139
                                ;adapter by assigning its ethernet ID
                                ;when more than one adapters exist on one
                                ; system.

         BusNo=@00          ;This keyword is used to desinate a RTL8139
                            ;adapter by assigning it's PCI bus number
                            ;when more than one adapters exist on one
                            ; system.(must be used with 'DeviceNo' keyword)

         DeviceNo=@0A       ;This keyword is used to desinate a RTL8139
                            ;adapter by assigning it's PCI Device number
                            ;when more than one adapters exist on one
                            ; system.(must be used with 'BusNo' keyword)

         Medium= 100/10      ;This keyword is used to force RTL8139 adapter
                            ;to speed 10M or 100M mode. If not present,
                            ;the driver will auto-detect the speed.

   Installation Procedure :
   ----------------------
      Before you start with the installation procedure, make sure that the
      adapter is properly installed and configured. Similarly, Make sure
      that your Microsoft Network Client is properly installed.
      (If not, The installation utility SETUP.EXE is located on Microsoft
      Network Client v3.0 for MS-DOS Disk. Run SETUP.EXE from Disk and the
      SETUP program screen will appear, and You must complete each of the
      questions. These options are specific to your needs. The installation
      procedure will transfer files to a specific directory on the client
      and modify existing configuration files to fit your specific needs.)

1. Change to the Microsoft Network Client subdirectory, and run
SETUP.EXE

      2. The screen will display some infomation. Press <Enter> .
                            ;to speed 10M or 100M mode. If not present,
                            ;the driver will auto-detect the speed.

1. Change to the Microsoft Network Client subdirectory, and run
SETUP.EXE

2. The screen will display some infomation. Press <Enter> .

3. Responds to the screen prompts, selecting "Change Network
Configuration",then press <Enter>.

4. Move the highlight to "Add Adapter", press <Enter>.

5. Select "Network adapter not shown on list below ...".

6. Insert the Realtek RTL8139 driver diskette in floppy A,and
specify your pathname A:/NDIS2DOS ,then press <Enter>.

      7. Follow screen instructions to complete the process. Simply
         pressing <Enter> for each screen display will select the default
         options. Press <Enter> until you reach the display prompting you
         to reboot your system.

-- Jack Chen --

========== End of File ==========